DOWNLOAD Panasonic SA-PT860E / SA-PT860EB / SA-PT860EG Service Manual ↓ Size: 8.83 MB | Pages: 127 in PDF or view online for FREE

There may be differences in the display order on the menu screen and computer screen.
This unit cannot play files recorded using packet write.

Discs must conform to UDF 2.0.

Discs must conform to UDF bridge (UDF 1.02/ISO9660).
This unit does not support multi-session. Only the default session is played.

Discs must conform to ISO9660 level 1 or 2 (except for extended formats).
This unit supports multi-session but if there are many sessions it takes more time for play to start. Keep the nhd8mbe

of sessions to a minimum to avoid this.

* For E/EG only

WMA

.WMA
.wma

Compatible compression rate: between 48 kbps and 320 kbps
You cannot play WMA files that are copy-protected.
This unit does not support Multiple Bit Rate (MBR: an encoding process for audio content that 
produces an audio file encoded at several different bit rates).

MP3

.MP3
.mp3

This unit does not support ID3 tags.
Sampling frequency and compression rate:

DVD-RAM, DVD-R/RW: 11.02, 12, 22.05, 24 kHz (8 to 160 kbps), 44.1 and 48 kHz (32 to 320 kbps)
CD-R/RW: 8, 11.02, 12, 16, 22.05, 24 kHz (8 to 160 kbps), 32, 44.1 and 48 kHz (32 to 320 kbps)

JPEG

.JPG
.jpg
.JPEG
.jpeg

JPEG files taken on a digital camera that conform to DCF Standard (Design rule for Camera File 
system) Version 1.0 are displayed. 

Files that have been altered, edited or saved with computer picture editing software may not be 
displayed.

This unit cannot display moving pictures, MOTION JPEG and other such formats, sti d::l pictures other
than JPEG (e.g. TIFF), or play pictures with attached audio.

*MPEG4

.ASF
.asf

You can play MPEG4 data [conforming to SD VIDEO specifications (ASF standard)/MPEG4 (Simple 
Profile) video system/G.726 audio system] recorded with Panasonic SD multi cameras or DVD 
recorders with this unit.
The recording date may differ from that of the actual date.

*DivX

.DIVX
.divx
.AVI
.avi

Plays all versions of DivX

fi

 video (including DivX

fi

6) [DivX video system/MP3, Dolby Digital or MPEG 

audio system] with standard playback of DivX

fi

 media files. Functions added with DivX Ultra are not 

supported.
DivX files greater than 2 GB or have no index may not be played properly on this unTd4t.
This unit supports all resolutions up to maximum of 720k 480 (NTSC)/720k 576 (PAL).
You can select up to 8 types of audio and subtitles on this unit.

25

The service modes can be activated by pressing various button combination on the main unit and remote control unit.

Below is the summary for the various modes for checking:

Main unit buttons

Remote control unit buttons

Application

Note

[STOP]

[0]

Error code check.

(Refer to the section
“8.2.1. Service Mode
Table 1” for more
information.)

[5]

Jitter checking.

[PAUSE]

Initial setting of laser drive current.

[FUNCTIONS]

DVD laser drive current check.

(Refer to the section
“8.2.2. Service Mode
Table 2” for more
information.)

[3]

CD laser drive current check.

[6]

Region display and mode.

[SOUND]

CPPM/CRM keys check.

[7]

Micro-processor firmware version check.

(Refer to the section
“8.2.3. Service Mode
Table 3“ for more
information.)

[

]

Initialization of the player (factory setting is restored).
Used after replacement of Micro-processor (DV5 LSI) IC,
FLASH ROM IC (IC8651), EEPROM IC (IC8611) and DVD
Module P.C.B.

[OK]

DVD Module P.C.B. reset.

[8]

DVD Module P.C.B. firmware version check.

(Refer to the section
“8.2.4. Service Mode
Table 4“ for more
information.)

[

]

Timer 1 check.

[

]

Timer 1 reset.

[

]

Timer 2 check.

[

]

Timer 2 reset.

An error code will be canceled if a power supply is turned OFF.

*1: CPPM is the copy guard function beforehand written in the disk for protection of copyrights.

*2: CEC is the consumer electronic control used for high-level user control of HDMI-connected devices.

*3: HDCP is the specification developed to control digital audio & video contents transmission for DVI or HDMI connections.

By pressing various button combinations on the main unit and remote control unit, you can activate the various service modes for
checking.

     • 

• 

• 

• 

Due to the limitations of the no. characters that can be shown on the FL Display, the “FL Display” button on the remote
control unit can be used to show the two display pages. (Display 1 / Display 2).

     • 

• 

• 

• 

Refer to Section 7.1 for the section on “Remote Control Key Buttons Operations”.

26

Initial setting of

laser drive

current 

Jitter check

Jitter check.
Jitter rate is measured and displayed.  
Measurement is repeatedly done in 
the cycle of one second. Read error 
counter starts from zero upon mode 
setting. 
When target block data failed to be 
read out, the counter advances by one 
increment. When the failure is caused 
by minor error, it may be corrected 
when retried to enable successful 
reading. 
In this case, the counter advances by 
one. When the error persists even 
after retry, the counter may jump by 
two or more.

FL Display sequence:
Display 1    2.

Jitter rate is shown in decimal notation to one 
place of decimal.
Focus drive value is shown in hexadecimal 
notation.

(Display 1)

Jitter rate

Jitter check
mode

(Display 2)

Lead
Error
Counter

Focus Drive 
Value

Press [POWER] or [STOP]
button to exit.

In STOP (with disc inside 
tray) mode, press [STOP] 
button on the main unit, 
and [5] button on 
the remote control unit, 
after Display 1 appears, 
then press [PLAY].

Press [FL Display] on 
remote control unit for next
page (FL Display).

Error code

check 

Error code check
The latest error code stored in the 
EEPROM IC is displayed.

Note: Refer to "Section 8.3 DVD Self
Diagnostic Function-Error Code" for 
more detailed information on the error 
codes.

Error code (play_err) is expressed in the 
following convention.
Error code = 0 x DAXX is expressed: 

DVDnn U12

Error code = 0 x DBXX is expressed: 

DVDnn H12

Error code = 0 x DXXX is expressed: 

DVDnn F123

Error code = 0 x 0000 is expressed: 

DVDnn F---

* "xx" denotes the error code

F / H / U

Cancelled automatically 
5 seconds later.
To exit, press [POWER]
button on main unit or 
remote control.

In STOP (no disc) mode, 
press [STOP] button on the 
main unit, and [0] button on 
the remote control unit. *With 
pointing of cursor up and 
down on display.

Press [FL Display] on 
remote control unit for next
page (FL Display) on values
of laser drive current.

Cancelled automatically 
5 seconds later.

In STOP (no disc) mode, 
press [STOP] button on the 
main unit, and [PAUSE] 
button on the remote 
control unit.

Initial setting of laser drive current. 
Initial current value for the DVD laser 
and CD laser is separately saved in 
the EEPROM IC.

FL Display sequence:
Display 1    2.

The value denotes the current in decimal 
notation.

The above example shows the initial current 
is XXXmA and YYYmA for CD laser and 
DVD laser respectively when the laser is 
switched on.

(Display 1)

Laser current
measurement 
mode

(Display 2)

CD
Laser 

DVD Laser 

FL Display

Key Operation

Front Key

Item

Description

Mode Name

27

FL Display

Key Operation

Front Key

Item

Description

Mode Name

CD laser drive 

current 

measurement

Press [FL Display] on 
remote control unit for next
page. (FL Display)

Cancelled automatically 
5 seconds later.

In STOP (no disc) mode, 
press [STOP] button on 
the main unit, and [3] 
button on the remote 
control unit.

The value denotes the current in decimal 
notation.

The above example shows the initial current is 
XXXmA and the measured value is YYYmA.

DVD laser 

drive current 

measurement

CD laser current 
measurement mode

(Display 1)

CD
laser initial
value

CD laser
value

(Display 2)

Press [FL Display] on 
remote control unit for next
page (FL Display) on values
of dvd drive current. 

Cancelled automatically 
5 seconds later.

In STOP (no disc) mode, 
press [STOP] button on the 
main unit, and 
[FUNCTIONS] button on 
the remote control unit.

The value denotes the current in decimal 
notation.

The above example shows the initial current 
is XXXmA and the measured value is 
YYYmA.

DVD laser current 
measurement mode

(Display 1)

DVD 
Laser 
Initial Value

DVD 
Laser 
Value

(Display 2)

DVD laser drive current measurement. 
DVD laser drive current is measured 
and the result is displayed together 
with the initial value stored in the 
EEPROM IC.
After the measurement, DVD laser 
emission is kept on. It is turned off 
when POWER key is switched off.

FL Display sequence:
Display 1    2.

CD laser drive current measurement.
CD laser drive current is measured 
and the result is displayed together 
with the initial value stored in the 
EEPROM IC.
After the measurement, CD laser 
emission is kept on. It is turned off 
when POWER key is switched off.

FL Display sequence:
Display 1    2. 

Region code display, TV broadcasting
system & the model no. information.

Note: Refer to Figure 8.1 for "Video
Design Information".

Region display

Cancelled automatically 
5 seconds later.

In STOP (no disc) 
mode, press [STOP] 
button on the main unit, 
and [6] button on the 
remote control unit.

N: no PAL / P: PAL

Model
No.
Information

N: NTSC / 6: PAL60

Region No.: 0-8

CPPM/CRM

Keys Check

Cancelled automatically 
5 seconds later.

In STOP (no disc) 
mode, press [STOP] 
button on the main unit, 
and [SOUND] button on 
the remote control unit.

0: NG
1: OK

0: NG
1: OK

CPPM/CRM refers to the Content 
Protection for Recordable Media and 
Pre-Recorded Media. It displays the 
existence of the keys as "1" or "0".
OK: Existing of keys.
NG: Non existing of keys.

28