DOWNLOAD Panasonic CS-C18GKD / CU-C18GKD / CS-C24GKD / CU-C24GKD Service Manual ↓ Size: 5.02 MB | Pages: 58 in PDF or view online for FREE

29

• Automatic operation can be set using remote control.
• This operation starts to operate with indoor fan at SLo speed for 25 seconds to judge the intake air temperature.
• After judged the temperature, the operation mode is determined by referring to the below standard.

• Then, the unit start to operate at determined operation mode, until it is switched off using remote control, with the setting

temperature as shown in below table.

• The setting temperature for all the operations can be changed one level up or one level down from the standard temperature as

shown in below table by pressing on the temperature up or temperature down button at remote control.

• The operation mode judging temperature and standard setting temperature can be increased by 2

°C permanently, by open the

circuit of JX1 at indoor electronic controller.

30

• When the thermo-off temperature (temperature which compressor stops to operate) is reached during:-

- Cooling operation - the compressor stops for 3 minutes (minimum) before resume operation.
- Soft Dry operation - the compressor stops for 6 minutes (minimum) before resume operation.

• If the operation is stopped by the remote control, the compressor will not turn on within 3 minutes from the moment operation

stop, although the unit is turn on again within the period.

• This phenomenon is to balance the pressure inside the refrigerant cycle.

• The compressor will start automatically if it has stopped for 7 minutes and the intake air temperature falls between the

compressor ON temperature (A) and compressor OFF temperature (B) during the period.

• This phenomenon is to reduce the built up humidity inside a room.

• Once the air conditioner is turned on, the compressor will not stop within 60 seconds in a normal operation although the intake air

temperature has reached the thermo-off temperature. However, force stop by pressing the OFF/ON operation button at the
remote control is permitted.

• The reason for the compressor to force operate at minimum 60 seconds is to allow the refrigerant oil run in a full cycle and return

back to the outdoor unit.

• If the temperature of the indoor heat exchanger falls below 2

°C continuously for 4 minutes or more, the compressor turns off.

The fan speed setting remains the same.

• This phenomenon is to protect the indoor heat exchanger from freezing and to prevent higher volume of refrigerant in liquid form

returning to the compressor.

• Compressor will restart again when the indoor heat exchanger temperature rises to 10

°C (Recovery).

• Restart control (Time Delay Safety Control) will be applied in this Control if the recovery time is too short.

31

• If the compressor is operating continuously for 5 minutes or longer and the temperature difference between intake air and indoor

heat exchanger is 2.5

°C or less for continuous 2 minutes, compressor will stop and restart automatically.

• Time Delay Safety Control is activated before the compressor restart.

• This is to prevent compressor from rotate reversely when there is an instantaneous power failure.

• When the compressor, outdoor fan motor and indoor fan motor are simultaneously started, the indoor fan motor will start to

operate at 1.6 second later.

• The reason of the difference is to reduce the starting current flow.

• Purpose is to prevent dew formation on indoor unit air discharge area.
• When room temperature is constant (±1°C) the following conditions occur for 30 minutes continuously, anti-dew formation will

activate:

- Remote Control setting temperature is less than 25°C.
- Compressor is on.
- Cooling operation mode.
- Indoor Fan motor operate at Low fan speed or QLo.

• This control is cancelled immediately when above condition is changed.
• Dew prevention is control by:

1. Increasing Air Flow Volume

a. Lo fan speed

Lo fan speed is changed to Lo+ after 30 min to prevent dew formation.

b. QLo fan speed

Dew formation may occurs at QLo cool, therefore QLo cool is operated only 1 hr 30 min (1 hr QLo, 30 min QLo +100
rpm). After that, it operates at QLo +180rpm (However Quiet LED remains on).

32

2. Norrowing

Vertical Airflow Direction
– During dew prevention control, Airflow Direction Auto-control angle change from 10° - 38° to 10° - 27° under

Cooling and Soft Dry operation mode.

– During dew prevention control, Airflow Direction Manual control angle change from 10°, 14°, 18°, 22°, 27° to

10°, 13°, 16°, 19°, 22° under Cooling and Soft Dry operation mode.

3. Narrowing

Horizontal Airflow Direction
– During dew prevention control, Airflow Direction Auto-control angle change form 0° - 44° to 14° - 30° under 

Cooling and Soft Dry operation mode.

– During dew prevention control, Airflow Direction Manual control angle change from 0°, 11°, 22°, 33°, 44° to

14°, 18°, 22°, 26°, 30° under Cooling and Soft Dry operation mode.