DOWNLOAD Panasonic CS-A18GKD / CU-A18GKD / CS-A24GKD / CU-A24GKD Service Manual ↓ Size: 9.99 MB | Pages: 70 in PDF or view online for FREE

37

• Indoor Fan Speed can be set using remote control.

• When set to Auto Fan Speed, the fan speed is adjusted between maximum and minimum setting as shown in the table.

- Fan speed rotates in the range of Hi, Me and Lo-.
- Deodorizing Control will be activated.

Speed

CS-A24GKD

CS-A18GKD

Cool, Dry

Heat

S Hi

Hi

1650

1430

Hi

1570

1400

Me

Me

1480

1320

Lo+

Lo

1380

1270

Lo

1280

1190

Lo-

Lo-

1070

980

S Lo

S Lo

830

760

SS Lo

300

300

Q SHi

Q Hi

1550

1330

Q Hi

1470

1300

Q Me

Q Me

1380

1220

Q Lo

1280

1170

Q Lo

1180

1090

38

• Auto Fan Speed during Cooling operation:

1. Indoor fan will rotate alternately between off and on as shown in below diagram.
2. At the beginning of each compressor start operation, indoor fan will increase fan speed gradually for deodorizing purpose.
3. For the first time the compressor operate, indoor fan will be switched to Hi fan speed from Lo- after 70 seconds from the

start of compressor. This cause the room temperature to achieve the setting temperature quickly.

4. During compressor stop, indoor fan will operate at Lo- for the beginning 20 seconds to prevent higher volume of refrigerant

in liquid form returning to the compressor.

5. After the compressor at turn off condition for 3 minutes, indoor fan will start to operate at Lo- to circulate the air in the

room. 
This is to obtain the actual reading of the intake air temperature.

6. For the resume of compressor operation, indoor fan will operate at Me fan speed to provide comfort and lesser noise

environment, after 70 seconds from the restart of compressor.

• Auto Fan Speed during Soft Dry operation:

1. Indoor fan will rotate alternately between off and Lo-.
2. At the beginning of each compressor start operation, indoor fan will increase fan speed gradually for deodorizing purpose.
3. When compressor at turn off condition for 6 minutes, indoor fan will start fan speed at Lo- to circulate the air in the room.

This is to obtain the actual reading of intake air temperature.

• Auto Fan Speed during Heating operation.

1. Indoor fan will rotate in the range of SLo 

→ Me according to the heat exchanger temperature.

39

• Manual fan speed adjustment can be carried out by using the Fan Speed selection button at the remote control.
• There are 3 types of fan speed settings: Lo, Me, Hi.

• There is 2 speed for outdoor fan motor. Outdoor fan speed can be changed to Hi or Lo according to outdoor temperature.
• For Cooling or Soft Dry operation when outdoor temperature reaches to 31

°C (Hi-speed), 29°C (Lo-speed).

• For Heating operation when outdoor temperature reaches to 13.5

°C (Hi-speed), 15.5°C (Lo-speed)

• When the air conditioner is turned on, the compressor and the outdoor fan will operate simultaneously.
• Likewise, both compressor and outdoor fan will stop at the same time if the unit is turned off.

• When the vertical airflow direction is set to Auto using the

remote control, the louver swings up and down as shown in
the diagram.

• When stopped with remote control, the discharge vent is

reset, and stop at the closing position.

• During Cooling operation or Soft Dry operation, indoor fan

motor may stop to rotate at certain periods. At that condition,
the louver will stop swinging and rest at the upper limit.

Cooling and Soft Dry Operation

• When the piping air temperature reaches 38°C, the
• louver is changed from upper to lower limit. When the
• piping air temperature falls to 35°C, the louver is changed

from lower to upper limit.

Heating Operation

• When the vertical airflow direction is set to Manual using the remote control, the automatic airflow is released and the airflow

direction louver move up and down in the range shown in the diagram.

• The louver can be adjusted by pressing the button to the desired louver position.
• When stopped with remote control, the discharge vent is reset, and stop at the closing position.

Cooling and Soft Dry Operation

Heating Operation

40

• When the horizontal airflow direction is set to Auto using the

remote control, the vanes swings left and right for Cooling
and Soft Dry (0°-44°), Heating (8°-36°) as shown in the
diagram.

• When stopped with remote control, the discharge vane is

reset, and stop at the reset position.

• During Cooling operation or Soft Dry operation, indoor fan

motor may stop to rotate at certain periods. At that condition,
the vane will stop swinging and rest at 22° angle.

• During Heating operation, the piping air temperature

reaches 38°C, the vanes swings left and right. When the
piping air temperature falls to 35°C, the vanes will stop
swing and rest at 22°.

• When the horizontal airflow direction is set to Manual using

the remote control, the automatic airflow is released and the
airflow direction vane move left and right in the range shown
in the diagram.
The louver can be adjusted by pressing the button to the
desired vane position.

• When stopped with remote control, the vanes is reset, and

stopped at reset position.