DOWNLOAD LG WT-E1275TP Service Manual ↓ Size: 2.31 MB | Pages: 71 in PDF or view online for FREE

SNAP RING.

Loosen the 6 fixing screws on the stator. 
(Lower 

upper position screws)

Check the direction of SNAP RING.
(The handle of snap  ring is toward to rotor and

stator.)

Preventing fallen the stator, tighten with one hand and
then loosen the last screw.

For assembly take care lead wire’s state,

it produce a noise and cut attach the rotor.

Loosen 14 Fixing screws on the Bearing Housing
ASM and pull up it.

Hall Sensor

Stator Housing

Water Guide

• To use the CHECK PROGRAM (QC TEST MODE),while pressing the  WATER LEVEL&WATER TEMP. buttons,

press the POWER button.Do not deposit any laundry in the wash tub while in this mode.   

• In QC TEST MODE all LEDs are on and press START(PAUSE) button to check over the following items.

1

2

3

4

5

6

7

8

9

10

Initial state

Press once

Press twice

Press 3 times

Press 4 times

Press 5 times

Press 6 times

Press 7 times

Press 8 time

Press 9 time

• 

Water level frequency is on
DISPLAY in the condition of no
water in TUB.

• Auto OFF

• All LEDS ON.

64~70 DISPLAY.

(The meaning of 64~70 number is

26.4~27.0kHz really)

The display differ from function.

• Laundry amount test.
• After detecting laundry amount 

the number of pulse is on the DISPLAY.

• COLD water ON.

• HOT water ON.

• SOFTENER INLET water ON.

• If the LID is opened, [DOOR OPEN]

is on the DISPLAY. In that case, close the
LID.

• DRAIN PUMP on.

• After detecting atmosphere temperature

the number is on the display

• After detecting IPM’s heat sink

temperature is the number is on the
DISPLAY.

•          this means 240V
• The display voltage twice rating voltage

(110~127V only)

• All LEDs off.

Many washing problems involve poor soil & stain removal, residues of lint and scum,
and fabric damage. For satisfactory washing results, follow these instructions.

• Use correct amount of detergent for load size, amount of soil and

water hardness.

• Use warm or hot water for normal soil.

Different water temperature may be required according to soil
type. (refer to page 12)

• Reduce load size.
• Wash with Jean or Soak(Turbo) & Jean wash cycle for heavy

soiled laundry.

• Separate heavily soiled items from lightly soiled ones.
• Pretreat stain and heavy soil according to directions shown on

page 11.

• Rub the stain with bar soap. Wash.
• Do not overfill fabric softener dispenser and do not pour liquid

fabric softener directly onto fabric. 
See page 14 for more instructions.

• Keep the recommendations against Scrud(waxy buildup). (refer

to scrud page14.)

• Use correct amount of detergent for load size, amount of soil and

water hardness.

• To restore discolored load of whites, use rust remover safe for

fabric.

• Install nonprecipitating water softener or an iron filter in your

water supply system for an ongoing problem.

• Before washing, run water for a few minutes to clear lines.

• Wash lint givers eg towels, flannelette sheets, separately from lint

collectors eg synthetic fabrics and remove tissues in pockets
before wash. See page 11 for sorting and caring before loading.

• Do not overload the washer

• Do not overload the washer.
• Some detergents need to be pre-dissolved, check the detergent

instructions. Try pre-dissolving the detergent.

• Increase water temperature using hot water safe for fabric.
• Use proper amount of detergent.

• Never pour chlorine bleach directly on fabric. 

See page 13 for adding liquid bleach.

• Fasten zippers, hooks, and buckles.
• Remove objects in pockets. See page 11 for caring before

loading.

• Do not overload the washer.

Poor soil
removal

• Not enough detergent
• Wash water temperature

too low.

• Overloading the washer
• Incorrect wash cycle
• Incorrect sorting
• Do not pretreat stain

• Undiluted fabric softener

dispensed directly onto
fabric

• A buildup caused by the

interaction of fabric
softener and detergent can
flake off and mark clothes

• Not enough detergent

• Iron or manganese in

water supply, water pipes,
or water heater

• Incorrect sorting
• Tissues left in pocket
• Overloading the washer

• Overloading the washer
• Undissolved detergent
• Use too much detergent

• Incorrect use of chlorine

bleach.

• Unfastened zippers,

hooks, buckles

• Ribs, tears and broken

threads

• Overloading the washer
• Degradation of fabric

Blue Stains

Holes, tears,
or snags

Black or gray
marks on
clothes

Yellow or
brown rust
stains

Lint

Residue or
detergent

For more detailed information for trouble shooting refer to page 37 to 45. 

• Water level does not

rise to the set level in
30 minutes.

• Water is not

completely drained in
12 minutes.

• Laundry unbalance

during spin.

• LID is opened in the

course of intermittent
spin, normal spin or
processing reservation.

WATER
SUPPLY

DRAINAGE

UNBALANCE

DOOR
OPEN

• Water faucet is closed?

• Water supply is interrupted.

• Inlet V/V is clogged with dirts.

• Connector has bad contact to

the inlet valve.

• Natural 4 pin connector has

bad contact to the P.W.B ASM.

• Is the drain hose located 

properly?

• Drain hose is folded or clogged

due to freeze or dirt.

• Bad Drain Pump part or

BLUE (WHITE) 3 pin connector to

the P.W.B ASM has bad 
connection.

• Laundry in the INNER TUB is filled

unevenly.

• Washer is tilted.

• Lid is opened during

intermittent spin or normal spin?

• Lid is opened while processing

reservation?

• Connector to the Reed S/W or

RED(ORANGE or PINK) 4 pin
connector

to the P.W.B ASM has bad 
connection.

• Open water faucet.

• Wait until water supply is

resumed.

• Clean or replace filter.

• Correct the connector contact.

• Same as above.

• Hung up drain hose at 0.9~1.2m

high. (For pump)

• Put the drain hose lower (For non-pump)
• Unclose the foreign objects within

drain hose.

• Replace drain pump or correct 

the connector contact.

• Try to fill laundry uniformly in the

inner tub.

• Adjust the leg.

• Closed the lid.

• Closed the lid.

• Correct the connector contact.

• Check and replace Lead Wire Asm.