LG WT-D182VG Service Manual ▷ View online
Note
7
(NORMAL TAB WITHOUY THREAD & ONE TOUCH TYPE INLET HOSE.)
One Touch Type
Separate Middle connector from Water Supply Hose
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and
the Pressing Handle that is attached to the
Water Supply Hose while pressing them.
1
Fixing Connectors to the Tap
Push the upper connector up till the rubber packing is in tight
contact with the tap.
Then tighten the 4 screws.
3
Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the Upper
and Middle Connectors.
Tighten the connectors by holding one connector
and twist middle connector to the right.
4
Connecting Middle Connector and Water Supply Hose
Press down the pressing rod of the Water
Supply Hose which was separated from middle
connector(refer to Step1) and then join it to
the middle connector.
5
Checking the water leakage
After connecting the hose, open the tap to
check for any water leakage.
In case of water leakage, close the tap and start
again from step 1.
If you skip step1, it may cause water leakage.
6
Conector
Medio
Etiqueta Fija
Manija de Presión
Barra de Presión
Barra de Presión
Manguera de Suministro de Agua
Empaque de Caucho
Tornillo
Etiqueta Fija
Empaque de Caucho
Placa Guía
Conector
Conector
Etiqueta Fijada
Conector
Medio
Conector
Medio
Conector
Manguera de Suministro de Agua
Barra de Presión
Manija de Presión
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the tap can
be placed in the middle.
In case the tap is large.
If the tap diameter is too large or is square,
open the 4 screw and take out the guide
plate and follow step 1.
2
Fixed Stiicker
Pressing Handle
Pressing Rod
Pressing Rod
Water Supply Hose
Middle connector
Rubber packing
Screw
Fixed sticker
Guide plate
Connector
Connector
Rubber packing
Connector
Middle
Connector
Pressing handle
Middle
Connector
Fixed sticker
Pressing rod
Water Supply Hose
8
Caution
1
Attach the water supply hose to the tap.
Screw Type
Push the water supply hose up so that the rubber
packing within the hose can adhere completely to
the tap.
packing within the hose can adhere completely to
the tap.
2
Connect the water supply hose to the tap.
Connect the water supply hose to the tap and then tighten
it by screwing it to the right.
it by screwing it to the right.
3
Check water leakage.
Connecting Water Supply Hose to the machine
After connecting the hose, open the tap to
check for any water leakage.
check for any water leakage.
• Connect the water supply hose to intel valve
of the washing machine, and then lock it by
turning the hose connecting part.
turning the hose connecting part.
• Check to see if there is a rubber seal inside
the connector.
For the cold water (1valve) model, Do not connect to the hot water supply.
It will damage your clothes.
It will damage your clothes.
9
1
Fit the end of the drain hose to the outlet of the drain pump and tighten the clamp.
Pump Model
Non-Pump Model
0.9~1.2m
Cable Tie
Cable Tie
0.9~1.2m
2
Firmly insert the free end of the drain hose into the drain opening of your home.
Make sure the soft rubber end is completely inside the drain opening.
Make sure the soft rubber end is completely inside the drain opening.
• If the water valves and drain are built into the wall,fasten the drain hose to one of the water hoses
with the cable tie (ribbed side on inside).
• If your drain is a standpipe,,fasten the drain hose to the standpipe with the cable tie provided.
1
Before connecting
Ensure that the hose clip is set as indicated here.
2
Connect the Elbow Hose
Push the elbow hose toward the body of the washing machine.
3
Place the Drain Hose
To change the direction of the hose,pull out the elbow hose and change
the direction.Repeat Step 2.
the direction.Repeat Step 2.
2-3. CONNECT THE DRAIN HOSE
WARNING
• The washer should never be installed or stored in a location subject to freezing temperatures.
If the washer was exposed to freezing temperatures prior to installation,allow it to stand at room
temperature for several hours before use.Damage to the water lines and internal mechanisms of
the washer can result.
• Water supply pressure must be between 14.5 psi and 116 psi ((100 ~800kPa)If the water supply
pressure is more than 116 psi,a pressure reducing valve must be installed.If you have
uncontrolled water temperature and pressure you should fit a temperature and pressure relief
valve
to ensure that water temperature and water pressure remain within the safe limits.Consult a
plumber or electrician if you are unable to adjust water temperature and or pressure.Failure to
do so can result in damage to the machine.
• Plug the power cord of washer into a properly grounded outlet..Failure to do this can result in
shock or serious injury.
The discharge height should be approximately 0.9~1.2m from the floor.
NOTE
10
3. OPERATING INSTRUCTION
3-1. IDENTIFICATION OF PARTS
POWDER AND LIQUID
DETERGENT BOX
DETERGENT BOX
WATER
SUPPLY HOSE
Make sure the
water does not
leak.
SUPPLY HOSE
Make sure the
water does not
leak.
POWER PLUG
If the supply cord is
damaged, it must be
replaced by the
manufacturer or its
service agents or
similarly qualified
person in order to
avoid a hazard.
If the supply cord is
damaged, it must be
replaced by the
manufacturer or its
service agents or
similarly qualified
person in order to
avoid a hazard.
Multi Clean Filter
DRAIN HOSE
for pump model
for pump model
Check if the drain
hose is hung up
before operating the
washing machine.
BASE
FUNCTION
SELECTOR
SELECTOR
TUB
START/PAUSE
BUTTON
Use to start or
stop the washing
machine
temporarily.
BUTTON
Use to start or
stop the washing
machine
temporarily.
ADJUSTABLE LEGS
Use to level the washing
machine for correct
balance & spin
operation.
Use to level the washing
machine for correct
balance & spin
operation.
DRAIN HOSE
for non pump
model
for non pump
model
BODY
Click on the first or last page to see other WT-D182VG service manuals if exist.