LG WT-80PV Service Manual ▷ View online
3-5. Safety Reed Switch
●
This reed switch system may differ from the old one. The reed switch is in PC board module
and works through contacting with magnets inside lid switch. It would not work until lid is
closed and current is passed through.\
and works through contacting with magnets inside lid switch. It would not work until lid is
closed and current is passed through.\
●
Do not place any magnetic object on the machine, which may lead to operation error.
3-6. Intelligence perception
●
Seven intelligence perception including unbalance, measurement, water level, door openness,
water temperature , water hardness and detergent density
● Unbalance perception may differ from that of old models. It percepts unbalance through
motor rotate speed of DD motor sensor under “SPIN” and abnormal operation.
3-7.10 Section level
● 10 section water level
● The water level can be adjusted manually with a cycle of
[7→8→9→10→1→2→3→4→5→6→7…] according to requirements as
the button is pressed.
● The water level can be adjusted manually with a cycle of
[7→8→9→10→1→2→3→4→5→6→7…] according to requirements as
the button is pressed.
Water
level/detergent
level/detergent
Water level
9
4. Identification of Parts
POWER DETERGENT
AND SOFTNER BOX
FILTER
BLEACH DISPENSER
*FUNCTION SLECTOR
*STAINLESS TUB
START/PAUSE
ADJUSTABLE LEGS
WATER SUPPLY
HOSE
●Make sure the water
does not leak~
POWER PLUG
●
If the supply cord
is damaged, it must
be replaced by the
qualified person.
is damaged, it must
be replaced by the
qualified person.
Holder can be fixable
*DRAIN HOSE
●Check if the drain hose
is hang up before
operating the washing
machine.
*MUTE BASE
10
5-2. Connecting Water Supply Hose
●
Connecting Water Supply Hose to the machine
Check to see if there is a black rubber seal inside the
connector. If not, it would cause water-leakage.
Hose
Rubber seal
Inlet valve
Connect the water supply hose to inlet valve of the
washing machine vertically.
washing machine vertically.
Connect the water supply hose to inlet valve of the
washing machine, and then lock it by turning the hose
connecting part.
washing machine, and then lock it by turning the hose
connecting part.
●Connecting Water Supply Hose to water tap
Separate connector from the Water Supply Hose by
pulling the Pressing Rod and the Pressing Handle that
is attached to the Water Supply Hose.
●
pulling the Pressing Rod and the Pressing Handle that
is attached to the Water Supply Hose.
●
If the tap diameter is too large , remove the guide plate
inside。
Connector
Press
Press
Water
Untighten the 4 screws on the upper connector and
turning the down connector to leave space about 3
screws between the two connectors.
turning the down connector to leave space about 3
screws between the two connectors.
If the tap diameter is too large,
remove the guide plate inside.
Upper-con
Guide
3 screws
Down-con
11
Adjust four screws on connectors to make sure that the
two screws near the wall are in tight contact with
outside of water tap.
The screws close to the wall should
be screwed beforehand.
Water tap
Push the upper connector up till the rubber packing
can adhere completely to the tap (Attention: Do not
remove the rubber packing).
Turning two screws to be in tight contact with water
tap. Then tighten the 2 screws.
Turn the lower connector to be in tight contact with
the upper one (Loose connection will cause the water
leakage). Make sure the clearance between the two
connectors is less than 3mm.
Confirmation
<3mm
<3mm
Connector
module
module
12
Click on the first or last page to see other WT-80PV service manuals if exist.