DOWNLOAD LG WF-D1617DD Service Manual ↓ Size: 3.69 MB | Pages: 54 in PDF or view online for FREE

For more detailed information for trouble shooting refer to page 39 to 49.

ERROR

WATER

SUPPLY 

DRAINAGE

UNBALANCE

DOOR

OPEN

WATER LEVEL
dose not rise to
the set level in 30
minutes.

"NO INLE"

lamp blinks

Water is not
completely
drained in 12
minutes.

Laundry
unbalance during
spin.

LID is opened in
the course of
intermittent spin,
normal spin or
processing
reservation.
SIGNAL
continuously
ringing. 

]DOOR OPEN ^

lamps blinks.

Water faucet is closed?
Water supply is interrupted.

Inlet V/V is clogged with
dirts.
Connector has bad contact
to the inlet valve.
BLUE 6 pin connector has
bad contact to the P.W.B
ASM.

Is the drain hose located
properly?
Drain hose is folded or
clogged due to freeze or dirt.
Bad Drain Pump part or
BLUE (WHITE) 3 pin
connector to the P.W.B ASM
has bad connection.

Laundry in the INNER TUB
is filled unevenly.

Washer is tilted.

Lid is opened during
intermittent spin or normal
spin?
Lid is opened while
processing reservation?
Connector to the Lid S/W or
NATURAL 6pin connector to
the P.W.B ASM has bad
connection.

Open water faucet.
Wait until water supply is
resumed.
Clean or replace filter.
Correct the connector
contact.
Same as above.

Hung up drain hose at
0.9~1.2m high.
Unclose the foreign objects
within drain hose.
Replace Drain Motor or
correct the connector
contact.

Try to fill laundry uniformly
in the inner tub.

Adjust the leg.

Closed the lid.

Closed the lid.

Correct the connector
contact.
Check and replace Lead
Wire Asm.

ERROR DECISION

BASIS

CAUSE FOR ERROR

OCCURRENCE

REMEDY

ERROR

OVER

FLOODING

ERROR

PRESSURE

SENSOR

MOTOR

ERROR

Water Pressure
Switch is off.

Check water leakage or
whether the drain hose is
hung on to drainage which is
0.9 m obove from floor.
Check blockage of air hole
or air tube.
Check &repair air leakage at
the air hole of outer tub the
air tube or connection parts.

Connector the PRESSURE
S/W ASM or BLUE 4 pin
connector to P.W.B ASM has
bad connection.
PRESSURE S/W is bad. (In
the initial state of QC TEST
MODE, the number on the
DISPLAY is less than 60 or
more than 104)

Connector the HALL Sensor
or Natural 6 Pin connector
to P.W.B ASM had bad
connection .
Connector the stator ASM,
and YELLOW 3 Pin or
Natural 6 Pin connector to
P.W.B ASM had bad
connection
Hall sensor is bad.
Locked by Bearing Housing

Hang drain hose which is
minimum 0.9m above from
floor.
Replace pressure sensor
switch
Remove the foreign objects
in pressure sensor switch

Correct the connector
contact.

Replace PRESSURE S/W
ASM.

Correct the connect contact.
Change Stator ASM.
Change Bearing Housing
ASM.
Change P.W.B ASM.
Change Stator ASM.

ERROR DECISION

BASIS

CAUSE FOR ERROR

OCCURRENCE

REMEDY

Where, what & how to check?

Result of Check

Possible Cause

How to repair & settle

1. Check whether connection between the

plug and the electrical is poor

2. Measure voltage of the electrical.

1. Measure resistance between both ends

of the power supply cord with both the
plug pins short-circuited.

2. Check whether every connector in the

bundle of connectors has a good
connection.

3. Check resistance of every wire to find

out a open wire.

1. Check resistance with power relay

switch turned on

2. Check the secondary voltage of the

transfomer.

3. Check whether the fuse is open.

If there are no defects in the above, 
it should be defect of the controller.

Poor

Around rating

0 V 

Less than 1

¥

Male & female
connectors separated

¥

Less than 0.5

More than 1.0 

10~14 V

0 V

Open

Over 120% voltage
than rating check

Change the controller if all
the electrical parts have no
defects.

Defect of the electrical

No defect

Defect of household
power supply

No defect

Open circult of the power
supply cord

Poor connection

Wire is opened.

No defect

Poor contact

No defect

Coil is open

Defect of the fuse

Change the electrical.

Call for power supply
company

Change the power supply
cord.

Remove the cause to give
strain and reconnect
them.

Change the lead wire

Change the AUTO OFF
Switch

Change the
transfomerformer.

Change the fuse.
CAUTION
Check the fuse rating
AC100~127V:125V 12A
AC220~240V:250V 6A

Where, what & how to check?

Result of Check

Possible Cause

How to repair & settle

1. Measure mains voltage at the wall outlet

2. Meaure voltage at the extended outlet

that the washer is plugged in if the
extended outlet is used and voltage at
the electrical outlet is normal in the
above.

1. Defect of LED.
2. Defect of LED driving circuit.
3. Defect of micom.

Less than 85% of the
rating

Less than 85% of the

rating

Low voltage

The dia of the lead wire is
smaller or many loads are
connected at the same
outlet

Defect of controller.

Change the controller.

To explain that it is
caused by low voltage in
electric supply and
recommend using a
transfomer if voltage has
been continuously low.

To use a transfomer
having a enough capacity
if using a transfomer.

Where, what & how to check?

Result of Check

Possible Cause

How to repair & settle

1. Measure voltage of the outlet that the

washer is plugged into during wash and
spin.

2. Reset symptom happens at specific time

zone repeatedly.

3. Check whether a transfomerlent power

cut happens. (Fluorescent lamp is
transfomeriently blinked)

1. If mains voltage and the drain motor

have no defects a defect of the controller
is highly possible.

Less than 80% of the
rating.

Mains voltage is too low
or size of a lead wire is
too small.

External noise inrushed.

Explain that it is caused
by low voltage in electric
mains and recommend
using a suitable size of
leads.

Explain it is caused by
using environment.
(It happens when
equipment with high
frequency is used
around)

Explain it is a problem of
electric supply
environment.

Change the controller.