DOWNLOAD LG WF-D1617DD Service Manual ↓ Size: 3.69 MB | Pages: 54 in PDF or view online for FREE

• Use to set a delayed finishing

time. 

• The time increases when the

button is pushed.

• The following settings are

indicated as the button is pushed
3    4    5    ...11    12    14    16
...46    48    3 HOUR.

• To cancel delay time, turn the

power switch off.
(refer to page 24)

• Use for selecting wash program.
• This button allows you to  select 8

different programs for different kinds of
laundry and dirtiness.

• Program selections light up in sequence

as follows: FUZZY(Normal)    WOOL
QUICK WASH    JEANS    SMART

CLEANING    ECO SAVE

FAVORITE      TUB CLEAN

FUZZY(Normal) etc. Select the desired
program by pressing the button.

• Use to start or pause the

washing process. 

• Repeats start and pause by

pushing the button.

• It only operates in FUZZY Program.
• During being detected by the sensor, the LED flashes green, orange and red in turn. And, after detecting, the

LED lights a specific color according to the detecting condition as follows:  

If the current washing condition (Detergent quantity, Water Temperature, water quality, etc.) is determined as
better than the standard one, it optimizes the algorithm to save the energy by decreasing washing 
time/strength, and the LED automatically turns to red.  
If the current washing condition is determined as worse than the standard one, it optimizes the algorithm 
by increasing washing 
time/strength, and the LED automatically turns to orange.
If the current washing condition is determined as equal to the standard one, the algorithm has no change and
the LED turns to green.

• Use to turn the power on or off.
• Push again and power goes on or off 
• The power goes off automatically

about 10 seconds after the wash is
finished.

* Because the detecting ability of the sensor may be decreased by using it for a long time, periodically use  TUB

CLEAN course to clean the tub. (refer to page 23)

* Even if the water level is changed by the user in FUZZY(Normal) Program, the sensor will still work. The sensor

algorithm may differ according to models.

* The control panel may differ according to different models.

Used for normal loads, this mode
automatically selects the most
appropriate conditions and
completes the sequence in one
operation. The built-in sensor
detects the size of the load and the
ideal wash power and wash, rinse
and spin times are set accordingly.

• Add the appropriate

quantity of Detergent
as indicated by the
WATER LEVEL.
Or follow the
Detergent
manufacturer’s
instructions

• Use neutral Detergent

appropriate for the
laundry.

• When washing woolens

use a mild Detergent
recommended for
washing wool.

• Select the

WOOL
program on
the Control
panel.

• Add the appropriate

quantity of Detergent
as indicated by the
WATER LEVEL
Or follow the
Detergent 
manufacturer’s
instructions

• Select the

QUICK
WASH
program on
the Control
panel.

• Select the

JEANS
program on
the Control
panel.

• Select the 

SMART
CLEANING
program on the
Control panel.

• Spread

the jean
evenly in
the tub

Use this program for washing delicate
fabrics such as lingerie and woolens.
(wash only “water washable” clothes)
Before washing your woolens check
the care label for the washing
instructions.
(wash only water washable clothes)

Use this mode when washing
lightly soiled clothes for a short
time. The highly recommended
laundry amount is under 2.0kg.

Use Jean program when washing
Jeans of different sizes

Use this program to increaserinsing
performance.
This would include underwear and
baby clothes.
If someone has sensitive skin or
skin trouble,use this program.

• The pulsator rotates for

8 seconds to detect the
laundry load.

• Then the WATER

LEVEL and the amount
of Detergent to be
used will be shown and
water will be supplied.

• Water will be

supplied for 2
minutes after the
start of the wash to
supplement the
water the laundry
has absorbed.

• When the wash

program ends, the
buzzer will ring for
10 seconds before
the Power goes
off automatically.

• If water is already in the tub, or putting

wet laundry into the tub before starting will
increase the WATER LEVEL. 

• With lightweight bulky loads, WATER

LEVEL can be set low.  

• When setting the WATER LEVEL manually,

do not set to Medium to prevent damage to
laundry.

• Washing with HOT water may damage the

laundry (Water is set to cold automatically).
Ensure that the load is under 2kg.

• In order to avoid  damage to laundry, the

spin cycle may appear slow. This also
avoids wrinkles and clothing may still
contain some water. This is normal.

• When static pressure of water is more

than 2kg/cm

2

, the QUICK WASH course

will be within 19min.

Use this mode to wash normal clothes or thick and heavy clothes which are excessively dirty. 
SOAK mode can be used with FUZZY or JEAN or FAVORITE program.

Press the POWER (AUTO OFF) button to turn power on.

Press the PROGRAM button to select the washing program.

Press the WASH button, to select SOAK program.

Add the Detergent. 

Add the laundry and press the START/PAUSE button.

• Keep pressing the WASH button until the light turns on

‘SOAK’ and ‘WASH’ simultaneously as next image.

• SOAK program only works when socking time is 40, 50 or

60 minutes. 

• Add the appropriate quantity of Detergent as the Detergent

manufacture instruction.

• The WATER LEVEL will be shown and water will be supplied.

Close the lid. 

Finish

• Water will be supplied for 2 minutes after the start of the wash to

supplement the absorbed water by the laundry. 

• When the wash program ends, the buzzer will ring for

10seconds before the Power goes off automatically.

• Order of Soak-Wash timing

• Select soaking time 40minutes, 50minutes, or 60minutes (including washing time) by pressing the Wash

button repeatedly.  

• If necessary, select the times of Rinse and the time for Spinning by pressing the Rinse or Spin buttons till

you reach the desired times. 

Soak-Wash