LG WD-BABYLUV1 Service Manual ▷ View online
8
Use spanner to remove transit bolts.
3
Confirm the distance between the appliance and the wall.
4
The tap connection and hose connection must be parallel.
5
Without removal of transit bolts
Spin noise
and
shaking
.
X 4 EA
Transit bolts
More than 2cm
If the distance is less than 2cm,
the water supply hose will
the water supply hose will
kink
or
fold
.
1. Normal Tap without thread &
screw
type inlet hose.
1.
Unscrew the fixing screw to
attach the tap.
attach the tap.
2.
Push the connector up till the
rubber packing is in tight contact
with the tap. Then tighten the 4
screws.
rubber packing is in tight contact
with the tap. Then tighten the 4
screws.
3.
Push the water supply hose
vertically upwards so that the
rubber packing within in the hose
can adhere completely to the tap
and then tighten it by screwing it
to the right.
vertically upwards so that the
rubber packing within in the hose
can adhere completely to the tap
and then tighten it by screwing it
to the right.
1.
Untighten the upper connector
screw.
screw.
2.
Push the upper connector up
till the rubber packing is in
tight contact with the tap. Then
tighten the 4 screws.
till the rubber packing is in
tight contact with the tap. Then
tighten the 4 screws.
3.
Connect the water supply hose
to the middle connector, pushing
the plate down.
to the middle connector, pushing
the plate down.
In case the diameter of the tap
is large remove the guide plate.
is large remove the guide plate.
Turn the middle connector not to
have water leaked.
have water leaked.
Make sure that the rubber seal is
inside the hose connector.
To separate the water supply
hose from the middle connector
shut off the tap.
Then pull the inlet hose down,
pushing the plate down.
Make sure that there are no
kinks in the hose and that it is
not crushed.
2. Normal Tap without thread &
one touch
type inlet hose (Single inlet models)
Upper
Connector
Connector
Fixing screw
Guide plate
Connector
Rubber packing
Upper
Connector
Connector
Rubber packing
Upper
Connector
Connector
Plate
Water supply
hose
hose
Rubber seal
Hose connector
Upper
Connector
Connector
Middle
connector
connector
Rubber
packing
packing
Upper
Connector
Connector
Fixing screw
Middle
connector
connector
Rubber
packing
packing
Upper
Connector
Connector
Plate
Water supply
hose
hose
9
Connect Drain Hose.
6
Connect power plug.
7
If the drain hose is not installed properly, the unit will not drain properly.
This allows water to back flow into the unit which can cause odors.
Refer to Owner Manual for proper drain hose installation.
The odor could also be coming from the home’s drain to which the drain hose is attached.
This allows water to back flow into the unit which can cause odors.
Refer to Owner Manual for proper drain hose installation.
The odor could also be coming from the home’s drain to which the drain hose is attached.
In this type of drain hose installation, the odor could be coming from the standpipe.
This odor can come up the drain hose and into the unit.
Pour a cup or two of bleach or vinegar down the home drain
and let it sit for 24 hours before running another cycle.
This will help eliminate odor from the home drain.
If a cycle is started too soon after doing this, it will not help the issue.
This odor can come up the drain hose and into the unit.
Pour a cup or two of bleach or vinegar down the home drain
and let it sit for 24 hours before running another cycle.
This will help eliminate odor from the home drain.
If a cycle is started too soon after doing this, it will not help the issue.
Connect the power plug to the wall outlet.
Avoid connecting several electric devices,
it may be the cause of a fire.
it may be the cause of a fire.
about 100 cm
about 145 cm
about 105 cm
Laundry tub
Max. 100cm
min. 60cm
Max. 100cm
min. 60cm
Retainer
Tie
strap
Hose
min. 60 cm
max. 100 cm
10
Check the horizontality with a level (Gage).
8
1 Step
If washing machine legs are loose or not screwed, then
screw up
with the spanner wrench.
Using the level, level the washing machine from front to back and side to side.
2 Step
Using the spanner wrench to adjust leg for
horizontality
and try for
Diagonal test
.
3 Step
Perform a Rinse and Spin with some clothing in the machine.
To do this, put 2~3kg of clothing in the unit, power on the unit, press the Rinse and Spin
button, and then start. When the unit reaches the spin cycle, watch for vibrations.
If the unit is vibrating, make small adjustments to the leg until they subside. (Try 2Step again)
To do this, put 2~3kg of clothing in the unit, power on the unit, press the Rinse and Spin
button, and then start. When the unit reaches the spin cycle, watch for vibrations.
If the unit is vibrating, make small adjustments to the leg until they subside. (Try 2Step again)
4 Step
Tighten
the lock nut against the base of the machine to
lock
the
position leg
.
Lower the foot until there is no gap between floor and foot.
And only use
And only use
adjustment rubber
when difference at the leg adjustment is more than
10mm
.
Place your right hand on the back, right corner and your left hand on the front,
left corner of the unit, then attempt to rock the unit from corner to corner.
Then, move your right hand to the front, right side and your left hand to the
back, left corner and attempt to rock the unit from corner to corner.
If the unit is level, it will not rock. However, if the unit is not level, it will rock.
If the unit rocks, it will be necessary to adjust the leveling feet of the unit.
Adjust the foot under the hand that is on the front of the machine.
left corner of the unit, then attempt to rock the unit from corner to corner.
Then, move your right hand to the front, right side and your left hand to the
back, left corner and attempt to rock the unit from corner to corner.
If the unit is level, it will not rock. However, if the unit is not level, it will rock.
If the unit rocks, it will be necessary to adjust the leveling feet of the unit.
Adjust the foot under the hand that is on the front of the machine.
How to perform a diagonal test:
A level
Higher
Tighten
Adjustable feet
Diagonal test
Tighten
Adjustable feet
Higher
Tighten
Adjustable feet
Lower
Lock nut
10mm
Adjustable bolt
Tighen the lock nut
4620ER3001B
(Gray)
(Gray)
for Wooden floors
Rubber Cup
4620ER3001A
(Black)
(Black)
for Tile floors
Test operation
9
11
1
Preparation
for washing.
for washing.
・Connect the power plug to the
outlet.
・Connect the inlet hose.
2
Press the power button.
3
Press the START/PAUSE
button.
button.
6
Check the water heating.
・Press “Temp.” button,
the present temperature will
be displayed.
be displayed.
・Check if the drum rotates
clockwise and counterclockwise.
5
Check automatic reverse turn.
4
Check the water supply.
・Check if water is supplied through
the detergent dispenser.
7
Check drain and spin.
・Power off and then power on.
Turn on Spin lamps after pressing
the Start/Pause button and Start
the machine again.
the Start/Pause button and Start
the machine again.
・Check drain and spin.
・Power off and then power on.
・Check if the door can be opened
・Check if the door can be opened
after Door Lock lamp turns off.
8
Power off and open the door.
9
Water removal.
・If SVC is needed during check,
remove the remaining water by
pulling out the hose cap.
pulling out the hose cap.
・In case of cotton program.
Click on the first or last page to see other WD-BABYLUV1 service manuals if exist.