LG WD-BABYLUV1 Service Manual ▷ View online
36
INLET VALVE
1
Disconnect the wiring receptacle.
2
Unscrew 2 screws from the back.
• Rating : 220/240V 50/60Hz
• Resistant : 3.5~4.5kΩ
• Resistant : 3.5~4.5kΩ
When reconnecting the connector
LOWER COVER
Open the lower cover cap by using coin and
pull out the lower cover to the arrow direction
after a screw is unscrewed.
pull out the lower cover to the arrow direction
after a screw is unscrewed.
VALVE #1 (MAIN)
VALVE #2 (PRE)
VALVE #2 (PRE)
White / Black - Black
Gray / White - Black
Gray / White - Black
DOOR
1
Open the door completely.
2
Remove the two screws from the hinge.
When removing the door assembly, it is
necessary to hold the bracket that is inner
of the cabinet cover.
necessary to hold the bracket that is inner
of the cabinet cover.
1
2
37
1
Take apart the cabinet gasket clamp.
2
Unscrew 2 screws from the cabinet cover.
4
Take apart the lower cover.
3
Open the lower cover cap and unscrew 1
screw inside.
screw inside.
1
Disassemble the control panel. (page 24)
2
Unscrew all the screws on the upper and lower
sides of the cabinet cover.
sides of the cabinet cover.
1
Take apart the tub gasket clamp.
2
Make sure that the drain hole of the gasket is
put beneath when reassembling the gasket.
put beneath when reassembling the gasket.
efer to the arrow mark on the tub cover.
GASKET ASSEMBLY
38
1
Remove the BACK COVER.
2
Unscrew the bolt to pull out the ROTOR
assembly.
assembly.
1
Disconnect the wiring connector.
2
Unscrew 6 bolts from the STATOR.
3
Remove the STATOR.
1
Pull out the hinge, pressing its snap.
2
Do not use the pulled-out hinge again. It may
be taken off during operation.
be taken off during operation.
ROTOR ASSEMBLY, STATOR ASSEMBLY, FRICTION DAMPER ASSEMBLY
Rotor
Bolt
(1)
Hinge,
Damper
Damper
(ROTOR ASSEMBLY)
(STATOR ASSEMBLY)
(DAMPER)
9a8a)
8a:a)
:a9a)
8a:a)
:a9a)
Note : Hook of connector (1) is on the backside
Motor Stator
89:
&RPPRQa+DaN)
&RPPRQa+EaN)
&RPPRQa+EaN)
Hall Sensor
Ha
Hb
Common
39
PUMP
1
Remove pump outlet hose.
2
Remove tub pump bellows.
3
Remove cap (Remaining Hose.)
4
Disconnect the wiring.
5
Unscrew 2 screws.
6
Remove the pump.
HEATER
1
Loosen the M6 heater nut to pull out the
heater.
heater.
CAUTION
When mounting the heater, be sure to insert
the heater into the heater clip on the bottom
of the tub.
the heater into the heater clip on the bottom
of the tub.
Tub Pump
Bellows
Bellows
Pump Outlet Hose
• Rating : 220~240V 1600W
• Resistant : 24.7~28.0Ω
• Resistant : 24.7~28.0Ω
• Rating : 220~240V 50HZ 30W
• Resistant : 160~177Ω
• Resistant : 160~177Ω
M6 heater nut
Click on the first or last page to see other WD-BABYLUV1 service manuals if exist.