LG SW6D2 Service Manual ▷ View online
Motor type
2-pole single phase shadding coil motor
Power consumption
70W
Motor output
20W
Lift head of draining
1m
Wash Tub
Material
Polypropylene resin
Spin timer
5min. clock system of mechanical type
S.D.Basket Revolution
50Hz : 1,350rpm
60Hz : 1,500rpm
Motor type
4-pole single phase condenser induction motor
Power Consumption
110-120V~, 60Hz
130W
220-240V~, 50/60Hz
130W
110-127V/220V~, 60Hz 220V~,50Hz
150W/130W
Motor output
40W
Wash tub
Material
Polypropylene resin
Wash timer
15min. clock system of mechanical type
Pulsator Revolution
120rpm
Motor type
4-pole single phase condenser induction motor
Power Consumption
110-120V~,60Hz
250W
220-240V, 50/60Hz
220W
110-127V/220V~, 60Hz 220V~,50Hz
250W/190W
Motor output
90W
MODEL WP-710N/WP-720N/EW-1003T-C
Dimensions (WxDxH)
725x420x905mm
Net weight
25kg
26.5kg
Power source Single AC 110V~120V, 60Hz
AC 120V, 60Hz
AC 220V, 50Hz
AC 240V, 50Hz
AC 220V, 50Hz
AC 240V, 50Hz
Dual AC 110-127 / 220V, 50/60 Hz
AC 110/120V, 50Hz
-4-
2. SPECIFICATIONS
WASH SIDE
SPIN SIDE
DRAIN PUMP (WP-710NP)
WP-710NP/WP-720NP
AC
22
0
~240
V, 50/60 Hz
-5-
3. CONTROLS LOCATION
(1) Control panel
(2) Washing cover
(3) Overflow filter
(4) Wash tub
(5) Pulsator
(6) Spin dryer cover
(2) Washing cover
(3) Overflow filter
(4) Wash tub
(5) Pulsator
(6) Spin dryer cover
Spinning will stop if the cover is
opened during operation.
Spinning will not start unless the
cover is closed.
opened during operation.
Spinning will not start unless the
cover is closed.
(7) Safety cover-2
(8) Spin dryer basket
(9) Safety cover-1
(10) Earth wire
(8) Spin dryer basket
(9) Safety cover-1
(10) Earth wire
(only for models with a two-prong plug)
(11) Drain hose
(12) Power cord
(12) Power cord
CONTROL PANEL
WP-720N(P)
WP-710N(P)/EW-1003T-C
(1) Water inlet
(2) Wash timer : Select the desired time for washing or rinsing.
(3) Drain selector
(2) Wash timer : Select the desired time for washing or rinsing.
(3) Drain selector
• Model WP-710N/720N : Select “WASH&RINSE” for washing and rinsing, and “DRAIN” to drain the wash tub.
• Model WP-710NP/720NP : Select “WASH&RINSE” for washing and rinsing with an overflow drain,
• Model WP-710NP/720NP : Select “WASH&RINSE” for washing and rinsing with an overflow drain,
and “DRAIN” to drain the wash tub, and “OFF” to turn off the drain pump.
(4) Spin timer : This timer determines the spinning time.
1
2
3
4
5
3
0
0
6
9
12
15
OFF
OFF
(pump model)
SPIN TIMER
DRAIN SELECTOR
WASH TIMER
OFF
DRAIN
WASH•RINSE
2
1
DO
N'
T R
OTA
TE
D
O
N
'T
R
O
TA
TE
3
4
DO
N'T
RO
TATE
1
2
3
4
5
3
0
0
6
9
12
15
OFF
OFF
(pump model)
SPIN TIMER
DRAIN SELECTOR
WASH TIMER
OFF
DRAIN
WASH•RINSE
2
DO
N'
T R
OTA
TE
D
O
N
'T
R
O
TA
TE
3
4
DO
N'T
RO
TATE
1
2
3
4
5
11
(for pump model)
1
6
7
8
9
10
11
12
-6-
4. DISASSEMBLY INSTRUCTIONS
4-1. Panel Assembly Replacement
1. Remove the screws fastening the back cover
and remove the back cover. (Fig.1)
2. Remove the vinyl tape fastening the lead wires
closed connector to the tub and disconnect the
lead wires. (Fig.2)
3. Disconnector the plunger valve strap from the rod.
(Fig.3)
4. Open the spin dryer cover and the safety cover-2,
and pull up and remove safety cover-1 in the
direction of the arrow. (Fig.4).
Fig.1
NOTE
Before attempting to service or adjust any part of
the washing machine, disconnect the electrical
power supply from the wall outlet.
Fig.2
Fig.3
5. Remove the screws fastening the panel. (Fig.5).
1
2
Fig.5
6. Remove the panel in the direction of the arrow.
(Fig.6).
Fig.6
Fig.4
-7-
To assemble the drain select arm to the switchbody,
reverse the disassembly procedure.
Fig.12
Fig.13
7. Remove the panel base assembly. (Fig.7).
Drain Select Arm Replacement
1. Pull out the knob for the drain selector.
2. Disconnect the plunger valve strap from the drain
select arm (Fig.12).
3. Lift the drain select arm in the direction of arrow and
at the same time rotate the drain select arm in the
direction of the white arrow until the hook of the drain
select arm matches the groove of the switch body.
To assemble the panel assembly, reverse the
disassembly procedure.
Timer Replacement
1. Disconnect the lead wires of the timers
2. Pull out the knob. (Fig.8)
3. Remove the screws fastening the switch body
and remove the switch body. (Fig.9).
Fig.
7
Fig.
10
Fig.8
NOTE
• When replacing the panel
base assembly,
fix the plunger valve strap properly.
• Securely solder connecting lead wires , or used
connectors and insulate
w
ell to prevent
Fig.9
Spin timer
Wash timer
4. Remove the timer by pushing the claw holding the
timer in the direction of the arrow.
Fig.
11
To assemble the timers to the switch body, reverse
the disassembly procedure.
overheating.
Click on the first or last page to see other SW6D2 service manuals if exist.