DOWNLOAD LG 41532 Service Manual ↓ Size: 22.57 MB | Pages: 59 in PDF or view online for FREE

No.

Process

Explanation

A.

Intermittent
spin

• To reach the correct set speed, the motor rotates clockwise and

counterclockwise directions after spin process starts.

• If the water level frequency is lower than 23.0 kHz, a washer senses

suds and starts suds removal process.

B.

Rinse
spin

• In this process, the remaining water during washing process is

extracted and the selected speed is kept.

• Removing suds process is in active mode at this cycle.

C.

Remaining
spin

• After spin finishes, the drum rotates by remaining spin power until it stops.

Motor power is off.

• This process is overlapped with next process. 

D.

Rinse water
supply

• Water supply for rinse process

E.

Rinse

• Rinsing process.

F.

Last
drainage

• After spin finishes and power is not supplied to motor, the drum

rotates by remaining spin power

• If rinse hold is selected, the drainage is not proceeded after rinse

finishes.

G.

Disentangling

• The same as item 9.

H.

Intermittent spin • The same as item A.

I.

Main spin1

• The same as item B.

J.

Main spin2

• At the end of a main spin, the spin speed will reach the selected rpm.

K.

Remaining spin • The same with item C.

L.

Disentangling

• After spin finishes, disentangling starts to remove unbalanced

laundry.

M.

End

• After 'end' signal is displayed, it stays for 8 seconds and power is

automatically turned off. (Auto type door switch)

• After door switch is off, end signal is displayed in the case of

manual type and it takes around 2 minute to turn off door switch.

6. PROGRAM CHART

n

wo

d-l

oo

C

es

ni

R 

art

x

E

hs

erf

e

R 

ma

et

S

ezi

ti

na

S

ykl

u

B

g

ni

d

d

e

B/

02

1
00

6

02

4

02

1
02

4

02

4

06

02

4

06

3

~

02

7

4

02

1

02

1

95

56

42

32

02

99

57

58

45

42

67

87

91

19

54

07 21 51

o

W

t

u

ok

r

W

r

a

e

/l

a

mr

o

N

l

a

us

a

C

14

2

74

15

06

41

02

51

yt

u

D 

yv

a

e

H

n

a

el

C 

dl

o

C

75

7  

6  

74

25

50

1

ss

er

px

E

W

hs

a

hs

a

W 

d

n

a

H

l

o

o

W/

r

a

e

W 

di

K

ts

eti

h

W

eti

h

W

d

e

g

g

u

R

41

02

81

52

75

06

06

7. TEST MODE

7-1. SAFETY CAUTION

There's built-in AC 110V and DC power in output terminal of PWB assembly in common. Be careful electric
shock when disconnecting parts while trouble shooting. (Wear Electro Static Discharge gloves when working.)
After cutting off the power when changing PWB assembly, disconnect or assemble.
Be careful static when handling PWB assembly, and use Electro Static Discharge plastic pack when delivering
or keeping it. 

7-2. LOAD TEST MODE.

The washer must be empty and the controls must be in the off state. 
1. Press the SPIN SPEED and SOIL LEVEL buttons simultaneously.
2. Press the POWER       button, while the above condition. Then buzzer will sound twice.
3. Press the START/PAUSE      button repeatedly to cycle through the test modes.

7-3. HOW TO CHECK THE WATER LEVEL FREQUENCY

Press the WASH TEMP and DELAY START button simultaneously.

The digits indicate the water level frequency ( x.1 kHz ).

So, for example a display indicating 241: a Water level frequency of 241 x.1 kHz

=  24.1 kHz

NOTES:

RPM < 220 : RPM = display / RPM > 200 : RPM = display X 10
WATER LEVEL : o255 = empty / o248 = normal / o255 = tub clean

None

1 time 

2 times 

3 times 

4 times 

5 times 

6 times 

7 times 

8 times 

9 times 

10 times 

11 times 

12 times 

13 times 

14 times

Turns on all lamps.

Tumble clockwise.

Low speed Spin.

High speed Spin.

Inlet valve for prewash turns on.

Inlet valve for main wash turns on.

Inlet valve for Hot water turns on.

Inlet valve for bleach turns on.

Inlet valve for steam turns on.

Tumble counterclockwise.

Heater turns on for 3 seconds.

Circulation pump turns on.

Drain pump turns on.

Steam water level sensor operates.

Steam Heater turns on for 1.2 sec.

LOAD TEST MODE

rpm (42~50)

rpm (55~65)

rpm (110~117)

Water level frequency (0~255)

Water level frequency (0~255)

Water level frequency (0~255)

Water level frequency (0~255)

rpm (42~50)

Water temperature

Water level frequency (0~255)

SKIP

SKIP

SKIP

SKIP

f

of

15 times

There’s built-in AC 120V and DC power in output terminal of PWB assembly in common. Be careful
electric shock when disconnecting parts while trouble shooting. (Wear Electro Static Discharge gloves
when working.)
After cutting off the power when changing PWB assembly, disconnect or assemble.
Be careful static when handling PWB assembly, and use Electro Static Discharge plastic pack when
delivering or keeping it. 

8. TROUBLESHOOTING

8-1. SAFETY CAUTION

8-2. ERROR MODE SUMMERY

WATER INLET

ERROR

1

UNBALANCE 

ERROR

2

DRAIN

ERROR

3

OVER FLOW 

ERROR

4

PRESSURE 

SENEOR

ERROR

5

DOOR OPEN 

ERROR

6

HEATING 

ERROR

7

• Correct water level (246) is not reached within 8 minutes 

after water is supplied or it does not reach the preset water
level within 25 minutes.

• The load is too small.
• The appliance is tilted.
• Laundry is gathered to one side.
• Non distributable things are put into the drum.

• Door not all the way closed.
• Loose electrical connections at Door switch and PWB

Assembly.

• The DOOR SWITCH ASSEMBLY is out of order.

• Not fully drained within 10 minutes.

• The SENSOR SWITCH ASSEMBLY is out of order.

• The THERMISTOR is out order.

• Water is overflowing (water level frequency is over 213). 

If               is displayed, the drain pump will operate to drain
the water automatically.

If you press the START/PAUSE button when an error is displayed, any error except 

will

disappear and the machine will go into the pause status.
In case of 

,

,

if the error is not resolved within 20 sec., or the in case of other errors,

if the error is not resolved within 4 min., power will be turned off automatically and the error code will
blink. But in the case of 

, power will not be turned off.