LG 60PY3RF-TB (CHASSIS:PP7AA) Service Manual ▷ View online
- 5 -
V
Module Specification
Market
Broadcasting system
Receiving system
Video Input (2EA)
Video Output (1EA)
S-Video Input (1EA)
Component Input (2EA)
RGB Input (1EA)
HDMI Input (2EA)
Audio Input (5EA)
Audio Output (2EA)
1
2
3
4
5
6
7
8
9
10
11
No
Item
Specification
Remark
PAL-D/K, B/G, I, NTSC-M
Upper Heterodyne
PAL-D/K, B/G, I, NTSC-M
PAL-D/K, B/G, I, NTSC-M
PAL-D/K, B/G, I, NTSC-M
Y/Cb/Cr, Y/ Pb/Pr
RGB-PC,
RGB-DTV
HDMI-PC
HDMI-DTV
PC Audio(1EA), Component(2EA), AV(2EA)
AV(1EA) ,Variable Audio Out(1EA)
L/R Input
L/R Output
- 6 -
ADJUSTMENT INSTRUCTION
1. Application Object
These instructions are applied all of the 60” PLASMA TV,
PP7AA
PP7AA
Chassis.
2. Note
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
(3) The adjustment must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.
there is no specific designation.
(4) The input voltage of the receiver must keep 100-220V~,
50/60Hz.
(5) Before adjustment, execute Heat Run for 30 minutes.
3. Adjustment items
3.1. PCB assembly adjustment items
(1) Channel memory.
- Download the channel data from BOM to EEPROM by
using LGIDS.
(2) Option adjustment following BOM.
- Tool Option1
- Tool Option2
- Area Option
- Tool Option2
- Area Option
3.2. SET assembly adjustment items
(1) Auto AV1 Color Balance
(2) Adjustment of White Balance
(3) Auto Component Color Balance adjustment
(2) Adjustment of White Balance
(3) Auto Component Color Balance adjustment
- standard equipment : MSPG925FA
(4) Auto RGB Color Balance adjustment
- standard equipment : MSPG925FA
4. EDID
* Caution
(1) Use the proper signal cable for EDID Download.
- Analog EDID : Pin3 exists.
- Digital EDID : Pin3 exists.
- Digital EDID : Pin3 exists.
(2) Never connect HDMI & DVI-D & DVI-A Cable at the same
time.
(3) Use the proper cables below for EDID Writing.
4-1. EDID Data
4-2. Data
(1) 60PY3RF-TB ANALOG(128Byte).
- BLOCK1 (128Byte).
(2) 60PY3RF-TB HDMI1(256Byte).
- BLOCK1 (128Byte).
- BLOCK2 (128Byte).
PP7AA(PP7AB)
PP7AA(PP7AB)
(Fig. 1)
Item
Manufacturer ID
Version
Revision
Condition
GSM
Digital : 1
Digital : 3
Hex Data
1E6D
01
03
For RGB EDID
For HDMI EDID
1
2
3
4
5
1
2
3
4
5
- 7 -
(3) 60PY3RF-TB HDMI2(256Byte).
- BLOCK1(128Byte).
- BLOCK2(128Byte).
=> Detail EDID Options are below(1,2,3,4,5)
1. Product ID
2. Serial No : Controlled on production line.
3. Month, Year : Controlled on production line.
3. Month, Year : Controlled on production line.
ex) Monthly: '11' => '0B'
Year : '2006' => '10'
4. Model Name : model name.
5. Checksum (7EH) -> Changeable by total EDID data.
5. ADC Calibration
6. Adjustment of AV
:
Mandatory point : All models are adjusted twice of NTSC and
PAL in AV mode.
6-1. Required Equipment
(1) Remote controller for adjustment.
(2) MSPG-925FS Pattern Generator (Which has Video Signal:
(2) MSPG-925FS Pattern Generator (Which has Video Signal:
7 Color Bar Pattern shown in Fig. 2).
1) Model: 202 / Pattern: 65
1) Model: 202 / Pattern: 65
- Case 1) TA Model : PAL-BGDHI (composite signal)
2) Model: 207 / Pattern: 65
- Case 2) MA Model : NTSC_J (composite signal)
6-2. Method of Auto AV Color Balance
(PAL_BGDHI)
(1) Input the Video Signal: 7 Color Bar signal into AV3.
(2) Set the PSM to Dynamic mode in the Picture menu.
(2) Set the PSM to Dynamic mode in the Picture menu.
(3) Press IN-START key on R/C for adjustment.
(4) Press the
G
(Vol. +) key to operate the set, then it becomes
automatically.
(5) After downloading complete, the ‘OK’ word appears.
(6) Auto-RGB OK means the adjustment is completed.
(6) Auto-RGB OK means the adjustment is completed.
6-3. Method of Auto AV Color Balance
(NTSC_J)
(1) Input the Video Signal: 7 Color Bar signal into AV3.
(2) Set the PSM to Dynamic mode in the Picture menu.
(2) Set the PSM to Dynamic mode in the Picture menu.
(3) Press IN-START key on R/C for adjustment.
(4) Press the
G
(Vol. +) key to operate the set, then it becomes
automatically.
(5) After downloading complete, the ‘OK’ word appears.
(6) Auto-RGB OK means the adjustment is completed.
(6) Auto-RGB OK means the adjustment is completed.
60PY3RF-TB
(ANALOG)
60PY3RF-TB
(HDMI)
Product ID
Product ID
Model Name
EDID table
59C3
5AC3
Hex
C359
C35A
Dec
50009
50010
C359
C35A
Model Name
MSPG925FS
Component
RGB-PC
AV
ADC
Model : 60
(1024*768 60Hz)
Pattern : 65
Model:215(720P)
Pattern : 65
* 720P/50Hz
7 Color Bar
PAL
INPUT SELECT AV1
Model : 202
(PAL-BGDHI)
Pattern : 65
* PAL 7 Color Bar
- System control RS-232 Host should be “PC“ for adjustment.
(Fig. 2)
(Fig. 2)
- 8 -
7. Adjustment of Component
7-1. Required Equipment
(1) Remote controller for adjustment.
(2) MSPG-925FS Pattern Generator. (Which has 720p/50Hz
(2) MSPG-925FS Pattern Generator. (Which has 720p/50Hz
YPbPr output Pattern shown in Fig. 3)
-> Model : 215 / Pattern : 65
-> Model : 215 / Pattern : 65
7-2. Method of Auto Component Color Balance
(1) Input the Component 720p/50Hz 7 Color Bar(MSPG-
925FS model:215, pattern:65) signal into Component.
(2) Set the PSM to Dynamic mode in the Picture menu.
(3) Press IN-START key on R/C for adjustment.
(4) Press the
G
(Vol. +) key to operate the set, then it becomes
automatically.
(5) After downloading complete, the ‘OK’ word appears.
(6) Auto-RGB OK means the adjustment is completed.
(6) Auto-RGB OK means the adjustment is completed.
8. Adjustment of RGB
8-1. Required Equipment
(1) Remote controller for adjustment.
(2) MSPG-925FS Pattern Generator ( Which has XGA
(2) MSPG-925FS Pattern Generator ( Which has XGA
[1024*768] 60Hz 1/2 black & white pattern shown in Fig. 4 )
8-2. Method of Auto RGB Color Balance
(1) Input the PC 1024x768 @ 60Hz 1/2 black & white pattern
(MSPG-925FS, Model:60, Pattern:65) into RGB. (using D-
sub to D-sub cable)
sub to D-sub cable)
(2) Set the PSM to Dynamic mode in the Picture menu.
(3) Press IN-START key on R/C for adjustment.
(4) Press the
G
(Vol. +) key to operate the set, then it becomes
automatically.
(5) After downloading complete, the ‘OK’ word appears.
(6) Auto-RGB OK means the adjustment is completed.
(6) Auto-RGB OK means the adjustment is completed.
9. White Balance
* Notice
- Before white balance,press the In-start key 2times and do
the reset like Fig1.
- Use the cortez inner pattern(216 gray pattern)
- To enter White-balance mode,press the IN-START key 2times.
- To enter White-balance mode,press the IN-START key 2times.
9-1. TEST Equipment
(1) Color Analyzer ( CA-210)
(2) PC(for communication through RS-232C) -> UART Baud
(2) PC(for communication through RS-232C) -> UART Baud
rate : 115200
(3) Pattern Generator (MSPG-925FA etc. )
9-2. Color Temperature & Color Coordinates
Setting
(1) When adjusting the Color Temperature of LCD, Color
Analyzer CA-210(Matrix should be corrected through CH9
of CS-1000) should be used.
of CS-1000) should be used.
(2) Adjust the Color Temperature based below adjustment
color coordinates.
(3) Even if CH9 of CA-210 is corrected with Matrix, there may
be many character of Module and Filter.
(4) Therefore Refer to the below Color Coordinates Target.
O
Standard Color Temperature & Color Coordinates Using CS-1000.
O
LCD Color Temperature & Color Coordinates Target Using
CA-210(CH 9)
* Target Value of Brightness, Color Coordinates, Color Temperature
Brightness : High Light : MIN 240 Cd/m2 (32 WXGA, AUO)
Brightness : High Light : MIN 240 Cd/m2 (32 WXGA, AUO)
MIN 240 Cd/m2 (37 WXGA, AUO)
MIN 240 Cd/m2 (42 WXGA,UXGA, LPL)
MIN 240 Cd/m2 (47 UXGA, LPL)
MIN 240 Cd/m2 (42 WXGA,UXGA, LPL)
MIN 240 Cd/m2 (47 UXGA, LPL)
Color-Coordinate :
High Light : Cool :X ; 0.276 ±0.002, Y ; 0.283 ±0.002
Warm : X ; 0.313 ±0.002, Y ; 0.329 ±0.002
Color Temperature : 11,000K±500K(Cool), 6,500K ±500K(Warm)
- System control RS-232 Host should be “PC” for adjustment.
(Fig. 3)
(Fig. 4)
COOL
WARM
11,000k
6,500k
Temp
Temp
Temp
0.276
0.313
0.283
0.329
Color Temperature
Color Coordinate
x
y
0.283±0.002
0.329±0.002
11000K
6500K
0.000
0.003
0.276±0.002
0.313±0.002
COOL
WARM
Mode
Temp
uv
Click on the first or last page to see other 60PY3RF-TB (CHASSIS:PP7AA) service manuals if exist.