LG 60PX950N-ZA / 60PX960-ZA (CHASSIS:PD02D) Service Manual ▷ View online
- 5 -
V
Model General Specification
No
Item
Specification
Remarks
1
Market
Albania, Austria, Belgium, Bosnia, Bulgaria,
36 Country
Coratia, Czech, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Ireland,
Italy, Kazakhstan, Latvia, Lithuania,
Luxembourg, Morocco, Netherlands, Norway,
Poland, Portugal, Romania, Russia, Serbia,
Slovenia, Spain, Sweden, Slovakia,
Switzerland, Turkey, Ukraine, UK
2
Broadcasting system
1) PAL/SECAM BG
EU (PAL Market)
2) PAL/SECAM DK
3) PAL
Ⅰ
/
Ⅱ
4) SECAM L/L’
5) DVB T
6) DVB C
DVB C(Only Sweden, Finland)
3
Receiving system
Analog : Upper Heterodyne
Digital : COFDM
4
Scart Jack (1EA)
PAL, SECAM
Scart 1 Jack is Full scart and support
RF-OUT(Analoge), MNT-OUT
5
Video Input (1EA)
PAL, SECAM, NTSC
Side AV
6
Component Input (1EA)
Y/Cb/Cr, Y/ Pb/Pr
rear
7
RGB Input
RGB-PC
Analog (D-Sub 15Pin)
8
HDMI Input (4EA)
HDMI-PC
HDMI1/DVI, HDMI2, HDMI3, HDMI4
HDMI-DTV
9
Audio Input (3 EA)
RGB/DVI Audio, Component, AV
L/R Input
10
SPDIF Out(1 EA)
SPDIF Out
11
USB(2 EA)
For SVC, S/W Download, X-Studio, DivX
12
Bluetooth
Bluetooth Phone(JPEG, MP3),
Profile : A2DP, BIP, FTP, GAVDP, HSP, OPP
Bluetooth Headset(mono, stereo)
13
Ethernet LAN
- 6 -
ADJUSTMENT INSTRUCTION
1. Application Range
This spec sheet is applied to all of the PD02D chassis.
2. Specification
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
(3) The adjustment must be performed in the circumstance of
25 °C ± 5 °C of temperature and 65 % ± 10 % of relative
humidity if there is no specific designation.
humidity if there is no specific designation.
(4) The input voltage of the receiver must keep 100 V ~ 240
V, 50 / 60 Hz.
(5) The receiver must be operated for about 5 minutes prior to
the adjustment when module is in the circumstance of over
15 °C
15 °C
- In case of keeping module is in the circumstance of 0 °C,
it should be placed in the circumstance of above 15 °C
for 2 hours
for 2 hours
- In case of keeping module is in the circumstance of below
-20 °C, it should be placed in the circumstance of above
15 °C for 3 hours,.
15 °C for 3 hours,.
O
After RGB Full White in HEAT-RUN Mode, the receiver
must be operated prior to the adjustment.
must be operated prior to the adjustment.
O
Enter into HEAT-RUN MODE
1) Press the POWER ON KEY on R/C for adjustment.
2) OSD display and screen display PATTERN MODE.
- Set is activated HEAT run without signal generator in this
2) OSD display and screen display PATTERN MODE.
- Set is activated HEAT run without signal generator in this
mode.
- Single color pattern ( WHITE ) of HEAT RUN MODE uses
to check panel.
- Caution : If you turn on a still screen more than 20
minutes (Especially digital pattern, cross hatch pattern),
an after image may be occur in the black level part of the
screen.
an after image may be occur in the black level part of the
screen.
3. PCB assembly adjustment
method
Caution: Using ‘power on’ button of the control R/C power on TV.
3-1 MAC Address and CI+ Key.
* Connect TV SET and PC which download MAC Address
Writing program by RS232C-Cable
(1) Start “MAC+CIKeyl.exe” Program and Click (3) Button to
connect TV and PC.
(2) Click (4) to download MAC Address.
(3) Click (5) to download CI+ Key.
(4) When download succeed, you can see “OK” on (6)
(3) Click (5) to download CI+ Key.
(4) When download succeed, you can see “OK” on (6)
* Each Chassis has it’ own MAC Address. Please be careful of
download.
3-2. Ping TEST
* This test is to check Network operation.
(1) Press "Power on" button of a service R/C.(Baud rate :
(1) Press "Power on" button of a service R/C.(Baud rate :
115200 bps)
(2) Connect RS232-C Signal Cable.
(3). Connect LAN cable to MAIN PCB Assembly.
(4) When network operates normally, you can see “OK”.
(3). Connect LAN cable to MAIN PCB Assembly.
(4) When network operates normally, you can see “OK”.
3-3. ADC Adjustment
O
Auto-control adjustment protocol(RS-232C)
(1) Adjustment of RGB
1) Convert to PC in Input-source.
2) Signal equipment displays
2) Signal equipment displays
Output Voltage: 700 mVp-p
Impress Resolution XGA (1920 x 1080 @ 60Hz)
Model : 225 in Pattern Generator
Pattern : 65 in Pattern Generator
Pattern : 65 in Pattern Generator
(MSPG-925 SERISE)
3) Adjust by commanding AUTO_COLOR_ADJUST
(2) COMPONENT input ADC
V
Convert to Component in Input-source.
V
Signal equipment displays
Impress Resolution 480i
MODEL: 209 in Pattern Generator(480i Mode)
PATTERN : 65 in Pattern Generator
PATTERN : 65 in Pattern Generator
(MSPG-925 SERISE)
Impress Resolution 1080i
MODEL: 225 in Pattern Generator(1080P Mode)
PATTERN: 65 in Pattern Generator
PATTERN: 65 in Pattern Generator
(MSPG-925 SERISE)
3-4. Insert Tool OPTION
and Model Name download.
(1) Press IN_START key on R/C to insert Tool OPTION
(2) On the “ Tool Option ”, Insert Tool Option by a number key
(3) Press the ENTER(
(2) On the “ Tool Option ”, Insert Tool Option by a number key
(3) Press the ENTER(
V
)
(4) Press ENTER(
V
) again.
(5) Select “OK to Download” by using
F
/
G
(VOL +/-) and press
G
(VOL +)
3-5. EDID(The Extended Display
Identification Data) download
(1) Press the ADJ KEY on R/C and enter EZ ADJUST.
(2) Select “5.EDID D/L” by using
(2) Select “5.EDID D/L” by using
D
/
E
(CH +/-) and press
ENTER(
V
).
(3) Select “Start” and press navigation key(
G
).
(4) EDID download is executed automatically.
(5) Press EXIT key on R/C
(5) Press EXIT key on R/C
* Caution
- Don t connect HDMI & D-sub Cable when the user
download EDID .
* Edid data and Model option download(RS232)
* EDID DATA
(1) Analog RGB
(2) HDMI 1
- 7 -
Model
Tool
Tool
Tool
Tool
Tool
Name
Value 1
Value 2
Value 3 Value 4 Value 5
50PX950N-ZA 37536
31279
54920
22892
2866
60PX950N-ZA 49824
31279
54920
22892
2866
50PX960-ZA
37536
31279
54920
22892
2866
60PX960-ZA
49824
31279
54920
22892
2866
- 8 -
a. Vender ID
3-6. Confirmation
(1) Press ‘InStart’ Key on Factory SVC Remote Controller.
And MUST check ADC & EDID ADJ status is OK.
4. SET assembly adjustment method
* Caution : Each PCB assembly must be checked by check JIG
set. (Because power PCB Assembly damages to PDP
Module, especially be careful)
Module, especially be careful)
4-1.POWER PCB Assembly Voltage
adjustment (Va/Vs Voltage Adjustment)
Test equipment : D.M.M 1EA
Connection Diagram for Measuring : refer to fig.4
Adjustment method
Connection Diagram for Measuring : refer to fig.4
Adjustment method
(1) Va adjustment
1) Connect + terminal of D. M.M. to Va pin of P811,
connect -terminal to GND pin of P811.
2) After turning VR502,voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top
(deviation; ±0.5V)
(deviation; ±0.5V)
(2) Vs adjustment
1) Connect + terminal of D. M..M. to Vs pin of P811,
connect -terminal to GND pin of P811.
2) After turning VR901, voltage of D.M.M adjustment as
same as Vs voltage which on label of panel right/top
( deviation ; ±0.5V)
( deviation ; ±0.5V)
4-2. Download Serial number (RS-232C)
V
Press “Power on” key of service R/C.
(Baud rate : 115200 bps)
(Baud rate : 115200 bps)
V
Connect RS232 Signal Cable to RS-232 Jack.
V
Write Serial number by use RS-232.
V
Must check the serial number at the Diagnostics of SET UP
menu.
(Refer to below ‘6.SET INFORMATION’).
menu.
(Refer to below ‘6.SET INFORMATION’).
4-3. Adjustment of White Balance
Required Equipment
O
Remote controller for adjustment
O
Color Analyzer ( CS-1000, CA-100,100+,CA-210 or same
produc: CH 10 (PDP)
produc: CH 10 (PDP)
* Please adjust CA-210, CA-100+ by CS-1000 before
measuring
O
Auto W/B adjustment instrument(only for Auto adjustment)
O
9 Pin D-Sub Jack(RS232C) is connected to the AUTO W/B
EQUIPMENT.
EQUIPMENT.
Before Adjust of White Balance, Please press POWER ONLY
key
Adjust Process will start by execute RS232C Command.
key
Adjust Process will start by execute RS232C Command.
O
Color temperature standards according to CSM and Module
O
CS-1000/CA-100+/CA-210(CH 10) White balance
adjustment coordinates and color temperature.
adjustment coordinates and color temperature.
* Manual W/B process (using adjusts Remote control)
Please Adjust in AV 1 MODE, Turn off Energy Saving Mode.
(1) Enter ‘PICTURE RESET’ on Picture Mode, then turn off
Fresh Contrast and Fresh colour in Advanced Control
(2) After enter Service Mode by pushing “ADJ” key,
(3) Enter White Pattern off of service mode, and change off ->
(3) Enter White Pattern off of service mode, and change off ->
on.
(4) Enter “W/B ADJUST” by pushing “
G
” key at “3. W/B
ADJUST”.
* Gain Max Value is 192. So, Never make any Gain Value over
192 and please fix one Value on 192, between R, G and B.
* Auto-control interface and directions
(1) Adjust in the place where the influx of light like floodlight
around is blocked. (Illumination is less than 10ux).
(2) Measure and adjust after sticking the Color Analyzer (CA-
100+, CA210 ) to the side of the module.
(3) Aging time
After aging start, keep the Power on (no suspension of
power supply) and heat-run over 5 minutes
power supply) and heat-run over 5 minutes
INOUT
HEX
HDMI1
10
HDMI2
20
HDMI3
30
HDMI4
40
INOUT
C/S
HDMI1
C62C
HDMI2
C61C
HDMI3
C60C
HDM4
C6FC
CSM
PLASMA
Cool
11000K
Medium
9300K
Warm
6500K
CSM
Color Coordinate
Temp
±Color Coordinate
x
y
Cool
0.276
0.283
11000K
0.002
Medium
0.285
0.293
9300K
0.002
Warm
0.313
0.329
6500K
0.002
Min
Tpy
Max
R-GAIN
0
192
192
G-GAIN
0
192
192
B-GAIN
0
192
192
Click on the first or last page to see other 60PX950N-ZA / 60PX960-ZA (CHASSIS:PD02D) service manuals if exist.