DOWNLOAD LG 47LH85 (CHASSIS:LA92F) Service Manual ↓ Size: 39.68 MB | Pages: 76 in PDF or view online for FREE

5.2.1 Overview

• W/B adj. Objective & How-it-works

- Objective: To reduce each Panel’s W/B deviation
- How-it-works: When R/G/B gain in the OSD is at 192, it

means the panel is at its Full Dynamic
Range. In order to prevent saturation of
Full Dynamic range and data, one of
R/G/B is fixed at 192, and the other two is
lowered to find the desired value. 

5.2.2 Equipment

1) Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12)
2) Adj. Computer(During auto adj., RS-232C protocol is

needed)

3) Adjust Remocon
4) Video Signal Generator MSPG-925F 720p/216-Gray

(Model:217, Pattern:78)

-> Only when internal pattern is not available

• Color Analyzer Matrix should be calibrated using CS-1000

5.2.3 Equipment connection 

5.2.4 Adj. Command (Protocol)

- LEN : Number of Data Byte
- CMD : Command
- VAL : Value of FOS Data
- CS : Checksum
- A : Acknowledge
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX}

• RS-232C Command(Automatic adjustment)

Ex)  wb 00 00 : Start Auto-adjustment of white balance.

wb 00 10 : Start Gain Adjustment (Inner pattern) 
ja 00 ff : Adjustment data
jb 00 c0 : 
…
…
wb 00 1f : End of Gain adjustment

* (wb 00 20(start), wb 00 2f(end)) -> In the case of Off-

set adjustment
wb 00 ff : End of white balance adjustment

• Adjustment Map

- 13 -

Co lo r An alyzer

 

Co m p ut er

 

Pat t ern Gen erat o r

 

RS -232C 

RS -232C 

RS -232C 

Probe

Signal Source

* If TV internal pattern is used, not needed

Connection Diagram of Automatic Adjustment

START

6E

50

03

00

CS

LEN

CMD

VAL

STOP

A

A

A

A

A

A

A

A

RS-232C COMMAND

Meaning

[CMD    ID      DATA]

wb

00

00

White Balance adjustment start.

wb

00

10

Start of adjust gain (Inner white pattern)

wb

00

1f

End of gain adjust

wb

00

20

Start of offset adjust(Inner white pattern)

wb

00

2f

End of offset adjust

wb

00

ff

End of White Balance adjust(Inner pattern disappeared)

ITEM

Command

Data Range

Default

(Hex.)

(Decimal)

Cmd 1

Cmd 2

Min

Max

Cool

R-Gain

j

g

00

C0

TBD

G-Gain

j

h

00

C0

TBD

B-Gain

j

i

00

C0

TBD

R-Cut

TBD

G-Cut

TBD

B-Cut

TBD

Medium

R-Gain

j

a

00

C0

TBD

G-Gain

j

b

00

C0

TBD

B-Gain

j

c

00

C0

TBD

R-Cut

TBD

G-Cut

TBD

B-Cut

TBD

Warm

R-Gain

j

d

00

C0

TBD

G-Gain

j

e

00

C0

TBD

B-Gain

j

f

00

C0

TBD

R-Cut

TBD

G-Cut

TBD

5.3.1 Automatic Adjustment
1) The adjustment condition should be set by the Power On

key.

2) Perform the zero calibration of the Color Analyzer and

place the probe close to the display center.

3) Connect the communication cable (RS-232C).
4) Select the desired model of the adjustment program and

perform the adjustment.

5) After the adjustment is ended (check the OK sign), check

the adjustment condition for each mode of the set.
(Warm, Medium, Cool)

6) Disconnect the probe and the communication cable to end

the adjustment.

* The adjustment should be started with "wb 00 00" and

ended with "wb 00 ff", and the offset should be adjusted
when necessary.

5.3.2 Manual adj. method
1) Set TV in Adj. mode using POWER ON
2) Press the ADJ of the R/C to enter into ‘EZ-ADJUST’.
3) Select ‘10.TEST PATTERN’ with the CH +/- key and press

the Enter key for 30 minutes or longer to perform the heat
run.

4) Perform the zero calibration of the Color Analyzer and fix

the sensor with the 10cm or less distance at the center of
the LCD module surface when adjusting.

5) Press the ADJ of the R/C to select ‘7.White-Balance’ of the

Ez-Adjust and press the right arrow key(

G

) to enter into the

adjustment mode. (As soon as you press ‘

G

’, the screen is

entered into the full white inner pattern.)

6) Fix one of the R/G/B gains to 192 and decrease the

remaining two gains to adjust not to exceed 192.

7) The adjustment is done at three white balances of Cool,

Medium and Warm

* Adjustment environment and reference

1) Environment illuminance

Adjust it to 10 LUX or less at the place where the light
source such as lamp should be blocked at maximum.

2) Probe location

: Maintain the Color Analyzer (CA-210) close to the

module surface by 10cm or less and keep the probe of
the Color Analyzer perpendicular to the module
surface (80°~ 100°).

3) Aging time

- Keep the power on after the aging start (with no power

off) to perform the heat run for 15 minutes or longer.

- Make sure that the back light is turned on by using no

signal and the full white pattern or others.

• Standard color coordinate and temperature using CS-

1000 (over 26 inch)

• Standard color coordinate and temperature using CA-

210(CH 9)

(1) Overview

- Option selection is only done for models in Non-USA

- Applied model: LA92A Chassis applied None USA

model(CANADA, MEXICO)

(2) Method

1) Press ADJ key on the Adj. R/C, then select Country

Group Menu

2) Depending on destination, select KR or US, then on the

lower Country option, select US, CA, MX. Selection is
done using +, - KEY

• TV

- Adjust directly if it's not a Wireless/Wired state 
- Adjust after changing to HDMI5 on the Wireless/Wired state

• Media-Box  

- Adjust on the Wireless/Wired state that is excepted the

HDMI5. 

- 14 -

Mode

Color Coordination

Temp

∆

UV

x

y

COOL

0.276

0.283

11000K

0.0000

MEDIUM

0.285

0.293

9300K

0.0000

WARM

0.313

0.329

6500K

0.0000

Mode

Color Coordination

Temp

∆

UV

x

y

COOL

0.276±0.002

0.283±0.002

11000K

0.0000

MEDIUM

0.285±0.002

0.293±0.002

9300K

0.0000

WARM

0.313+0.002

0.329±0.002

6500K

0.0000

- 15 -

Step 1) Turn on TV
Step 2) Press EYE key of Adj. R/C
Step 3) Cover the Eye Q II sensor on the front of the using

your hand and wait for 6 seconds

Step 4) Confirm that R/G/B value is lower than 10 of the

“Raw Data (R: G: B: )” .

If after 6 seconds, R/G/B value is not lower than 10,
replace Eye Q II sensor

Step 5) Remove your hand from the Eye Q II sensor and wait

for 6 seconds

Step 6) Confirm that “B. Light(xxx)” value increases from 0.

If change is not seen, replace Eye Q II sensor

< step 2>                         < step 3>                         < step 4>

< step 5>                        < step 6>

- Check that Power Cord is fully inserted to the set

(If loose, re-insert)

- Unit w/ fully inserted power cord and A/V arrives to the auto-

check process.

- Connect D-terminal AV JACK TESTER
- Auto CONTROLLER(GWS103-4) ON
- Perform GND TEST
- If NG, Buzzer will sound to inform the operator
- If OK, changeover to I/P check automatically

(Remove CORD,A/V from AV Jack Box)

- Perform I/P test
- If NG, Buzzer will sound to inform the operator
- If OK, Good lamp will lit up and the stopper will allow the

pallet to move on to next process.

NEUTRAL

• LEAKAGE CURRENT: At 0.5mArms

Green Eye-Check 

Sensor Data:

      1 

Backlight:     0

 

O.K 

Green Eye-Check 

Sensor Data:   215 

Backli ght :     100 

- 16 -

300

200

200T

810

803

804

400

520

540

805

900

550

802

530

801

121

120

510

570

500

560

310

700

710

770

780

790

720

730

750

740

760

A2

LV1

A10

LV2

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These

parts are identified by       in the Schematic Diagram and EXPLODED VIEW. 

It  is  essential  that  these  special  safety  parts  should  be  replaced  with  the  same  components  as

recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. 

Do not modify the original design without permission of manufacturer.

521