LG 47LH80YD (CHASSIS:LB91F) Service Manual ▷ View online
5.1. White Balance Adjustment
5.1.1 Overview
• W/B adj. Objective & How-it-works
- Objective: To reduce each Panel’s W/B deviation
- How-it-works
: When R/G/B gain in the OSD is at 192, it means the
- How-it-works
: When R/G/B gain in the OSD is at 192, it means the
panel is at its Full Dynamic Range. In order to prevent
saturation of Full Dynamic range and data, one of R/G/B
is fixed at 192, and the other two is lowered to find the
desired value.
saturation of Full Dynamic range and data, one of R/G/B
is fixed at 192, and the other two is lowered to find the
desired value.
5.1.2 Equipment
1) Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12)
2) Adj. Computer(During auto adj., RS-232C protocol is
2) Adj. Computer(During auto adj., RS-232C protocol is
needed)
3) Adjust Remocon
4) Video Signal Generator MSPG-925F 720p/216-Gray
4) Video Signal Generator MSPG-925F 720p/216-Gray
(Model:217, Pattern:78)
-> Only when internal pattern is not available
• Color Analyzer Matrix should be calibrated using CS-1000
5.1.3 Equipment connection
5.1.4 Adj. Command (Protocol)
- LEN : Number of Data Byte
- CMD : Command
- VAL : Value of FOS Data
- CS : Checksum
- A : Acknowledge
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX}
- CMD : Command
- VAL : Value of FOS Data
- CS : Checksum
- A : Acknowledge
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX}
• RS-232C Command(Automatic adjustment)
Ex) wb 00 00 : Start Auto-adjustment of white balance.
wb 00 10 : Start Gain Adjustment (Inner pattern)
ja 00 ff : Adjustment data
jb 00 c0 :
…
wb 00 1f : End of Gain adjustment
ja 00 ff : Adjustment data
jb 00 c0 :
…
wb 00 1f : End of Gain adjustment
* (wb 00 20(start), wb 00 2f(end)) -> In the case of Off-
set adjustment
wb 00 ff : End of white balance adjustment
wb 00 ff : End of white balance adjustment
• Adjustment Map
5.2. Adjustment of White Balance
5.2.1 Automatic Adjustment
1) The adjustment condition should be set by the Power On
key.
2) Perform the zero calibration of the Color Analyzer and
place the probe close to the display center.
3) Connect the communication cable (RS-232C).
4) Select the desired model of the adjustment program and
4) Select the desired model of the adjustment program and
perform the adjustment.
5) After the adjustment is ended (check the OK sign), check
the adjustment condition for each mode of the set.
(Warm, Medium, Cool)
(Warm, Medium, Cool)
6) Disconnect the probe and the communication cable to end
the adjustment.
* The adjustment should be started with "wb 00 00" and
ended with "wb 00 ff", and the offset should be adjusted
when necessary.
when necessary.
5.2.2 Manual adj. method
1) Set TV in Adj. mode using POWER ON
2) Press the ADJ of the R/C to enter into ‘EZ-ADJUST’.
3) Select ‘10.TEST PATTERN’ with the CH +/- key and press
2) Press the ADJ of the R/C to enter into ‘EZ-ADJUST’.
3) Select ‘10.TEST PATTERN’ with the CH +/- key and press
the Enter key for 30 minutes or longer to perform the heat
run.
run.
4) Perform the zero calibration of the Color Analyzer and fix
the sensor with the 10cm or less distance at the center of
the LCD module surface when adjusting.
the LCD module surface when adjusting.
5) Press the ADJ of the R/C to select ‘7.White-Balance’ of the
Ez-Adjust and press the right arrow key(
G
) to enter into the
adjustment mode. (As soon as you press ‘
G
’, the screen is
entered into the full white inner pattern.)
6) Fix one of the R/G/B gains to 192 and decrease the
remaining two gains to adjust not to exceed 192.
7) The adjustment is done at three white balances of Cool,
Medium and Warm
- 13 -
Co lo r An alyzer
Co m p ut er
Pat t ern Gen erat o r
RS -232C
RS -232C
RS -232C
Probe
Signal Source
* If TV internal pattern is used, not needed
Connection Diagram of Automatic Adjustment
START
6E
50
03
00
CS
LEN
CMD
VAL
STOP
A
A
A
A
A
A
A
A
RS-232C COMMAND
Meaning
[CMD ID DATA]
wb
00
00
White Balance adjustment start.
wb
00
10
Start of adjust gain (Inner white pattern)
wb
00
1f
End of gain adjust
wb
00
20
Start of offset adjust(Inner white pattern)
wb
00
2f
End of offset adjust
wb
00
ff
End of White Balance adjust(Inner pattern disappeared)
ITEM
Command
Data Range
Default
(Hex.)
(Decimal)
Cmd 1
Cmd 2
Min
Max
Cool
R-Gain
j
g
00
C0
TBD
G-Gain
j
h
00
C0
TBD
B-Gain
j
i
00
C0
TBD
R-Cut
TBD
G-Cut
TBD
B-Cut
TBD
Medium
R-Gain
j
a
00
C0
TBD
G-Gain
j
b
00
C0
TBD
B-Gain
j
c
00
C0
TBD
R-Cut
TBD
G-Cut
TBD
B-Cut
TBD
Warm
R-Gain
j
d
00
C0
TBD
G-Gain
j
e
00
C0
TBD
B-Gain
j
f
00
C0
TBD
R-Cut
TBD
G-Cut
TBD
* Adjustment environment and reference
1) Environment illuminance
Adjust it to 10 LUX or less at the place where the light
source such as lamp should be blocked at maximum.
source such as lamp should be blocked at maximum.
2) Probe location
: Maintain the Color Analyzer (CA-210) close to the
module surface by 10cm or less and keep the probe of
the Color Analyzer perpendicular to the module
surface (80°~ 100°).
the Color Analyzer perpendicular to the module
surface (80°~ 100°).
3) Aging time
- Keep the power on after the aging start (with no power
off) to perform the heat run for 15 minutes or longer.
- Make sure that the back light is turned on by using no
signal and the full white pattern or others.
• Standard color coordinate and temperature using CS-1000
• Standard color coordinate and temperature using CA-210(CH 10)
5.3 Option selection per country
(1) Overview
- Option selection is only done for models in Non-USA
- Applied model: LA92A Chassis applied None USA
model(CANADA, MEXICO)
(2) Method
1) Press ADJ key on the Adj. R/C, then select Country
Group Menu
2) Depending on destination, select KR or US, then on the
lower Country option, select US, CA, MX. Selection is
done using +, - KEY
done using +, - KEY
• TV
- Adjust directly if it's not a Wireless/Wired state
- Adjust after changing to HDMI5 on the Wireless/Wired state
- Adjust after changing to HDMI5 on the Wireless/Wired state
• Media-Box
- Adjust on the Wireless/Wired state that is excepted the
HDMI5.
5.4 EYE-Q Function Check
Step 1) Turn on TV
Step 2) Press EYE key of Adj. R/C
Step 3) Cover the Eye Q II sensor on the front of the using
Step 2) Press EYE key of Adj. R/C
Step 3) Cover the Eye Q II sensor on the front of the using
your hand and wait for 6 seconds
Step 4) Confirm that R/G/B value is lower than 10 of the
“Raw Data (R: G: B: )” .
If after 6 seconds, R/G/B value is not lower than 10,
replace Eye Q II sensor
replace Eye Q II sensor
Step 5) Remove your hand from the Eye Q II sensor and wait
for 6 seconds
Step 6) Confirm that “B. Light(xxx)” value increases from 0.
If change is not seen, replace Eye Q II sensor
< step 2> < step 3> < step 4>
< step 5> < step 6>
5.5 Wireless Pairing
(1) Overview
To set 1:1 connection from selecting the same Wireless
channel on the TV and Media-Box, and fixing Mac address.
channel on the TV and Media-Box, and fixing Mac address.
* Set this on the Wired (HDMI cable connection) state.
(2) Method
1) Press ADJ Key on the adjustment R/C and select “9.
Wirelesss Pairing” and access to the Manu with using the
ENTER key.
ENTER key.
2) Make to display “OK” on paired stauts of items by using F/
G , after select LRP Channel
3) Media-box turn off/on and then confirm connection of
Wireless, after remove HDMI cable
- 14 -
Mode
Color Coordination
Temp
∆UV
x
y
COOL
0.276
0.283
11000K
0.0000
MEDIUM
0.285
0.293
9300K
0.0000
WARM
0.313
0.329
6500K
0.0000
Mode
Color Coordination
Temp
∆UV
x
y
COOL
0.276±0.002
0.283±0.002
11000K
0.0000
MEDIUM
0.285±0.002
0.293±0.002
9300K
0.0000
WARM
0.313+0.002
0.329±0.002
6500K
0.0000
Green Eye-Check
Sensor Data:
1
Backlight: 0
O.K
Green Eye-Check
Sensor Data: 215
Backli ght : 100
- 15 -
6. USB S/W Download (option)
(1) Overview
USB Download is function for qickly service through S/W
upgrade and for S/W upgrade application that is necessary
adjust board.
upgrade and for S/W upgrade application that is necessary
adjust board.
(2) Methood
1. Put the USB Stick to the USB socket
2. Automatically detecting update file in USB Stick
2. Automatically detecting update file in USB Stick
- If your downloaded program version in USB Stick is Low, it
didn’t work.
But your downloaded version is High, USB data is
automatically detecting
automatically detecting
3. Show the message “Copying files from memory”
4. Updating is staring.
4. Updating is staring.
5. Updating Completed, The TV will restart automatically.
6. If your TV is turned on, check your updated version and Tool
6. If your TV is turned on, check your updated version and Tool
option. (explain the Tool option, next stage)
* If downloading version is more high than your TV have, TV
can lost all channel data. In this case, you have to
channel recover. if all channel data is cleared, you didn’t have
a DTV/ATV test on production line.
a DTV/ATV test on production line.
* After downloading, have to adjust TOOL OPTION again.
1. Push "IN-START" key in service remote controller.
2. Select "Tool Option 1" and Push “OK” button.
3. Punch in the number. (Each model has their number.)
4. Completed selecting Tool option.
2. Select "Tool Option 1" and Push “OK” button.
3. Punch in the number. (Each model has their number.)
4. Completed selecting Tool option.
7. Micom JIG Download
(1) Overview
In case of Weltrend Micom applied to TV main and Media-Box
main b/d, excuate upgrade by using the Download jig. becuase
USB download is impossible
main b/d, excuate upgrade by using the Download jig. becuase
USB download is impossible
(2) Method
1) Connect Computer and Jig, TV or Media Box.
2) Excuate Weltren MCU ISP program, and Load Download file.
2) Excuate Weltren MCU ISP program, and Load Download file.
3) When press F1 or Auto button, start download.
4) Confirm download is normal through Print .
5) Press “IN-START” on adjust R/C, Confirm S/W version.
4) Confirm download is normal through Print .
5) Press “IN-START” on adjust R/C, Confirm S/W version.
8. TOOL OPTION
(1) Overview
Adjust without adjustment equipment at option change, becuase
model name and specificaion displayed on menu.
model name and specificaion displayed on menu.
* Chage prohivition at pleasure.
(2) Method
1) Push "IN-START" key in service remote controller.
2) Select "Tool Option 1" and Push “Enter” Key.
3) "Tool Option 1" is changeable manu for Inch, Tool, Module
2) Select "Tool Option 1" and Push “Enter” Key.
3) "Tool Option 1" is changeable manu for Inch, Tool, Module
maker, Module revision.
Tool Option1: Inch, Tool, Maker, Module Rev.
Tool Option2: HDMI Count, HDMI Switch IC, Component Count,
Tool Option2: HDMI Count, HDMI Switch IC, Component Count,
S-Video, RCA AV Count, Scart Count
Tool Option3: EMF(JPEG,MP3), Divx, Bluetooth, Digital Eye,
Headphone, OPC, EPA, e-Manual, Audio Amp,
LED Type
LED Type
Tool Option4: Clear QAM, Local Dimming, THX, Digital Demod,
Analog Demod, THS Media Director
(3) Tool option setting.
MODEL
Display
opt1
opt2
opt3
opt4
47”
TV
33473
4168
548
4352
Media-Box
33473
4424
52132
4352
55”
TV
45761
4168
548
4352
Media-Box
45761
4424
52132
4352
- 16 -
BLOCK DIAGRAM_TV
S-Flash
(32Mb)
NTP3100L
(D-AMP)
X100
X-tal(12Mhz)
R
es
et
I2S
MCLK
For w
ireless
IR &
Local
KEY
24C16
DDR2 (1Gb
)
X900
X-tal(24
**)
NVRAM
24C512
EEPROM
DDR(512Mb
)
DDR(512Mb
)
DDR2(512Mb)
DDR2(512Mb)
NAND-F
lash
(512Mb)
L
G
E3159GV
S5
KIA7427F
For w
ired
&
General
L
G
E7329
Ursa
USB
RS-232
Onl
y
for serv
ice
W
T
61P8
Micom
MODULE
HDMI_2
HDMI_3
NO
T
F
O
R US
ER
Conn
ect to Rx b/
d
MAIN BLOCK-DIAGRAM
BLOCK DIAGRAM_TV
Click on the first or last page to see other 47LH80YD (CHASSIS:LB91F) service manuals if exist.