DOWNLOAD LG 42SL90-UA (CHASSIS:LA92S) Service Manual ↓ Size: 5.7 MB | Pages: 44 in PDF or view online for FREE

4) HDMI IV [C/S: 1D9A] 

EDID Block 0, Bytes 0-127 [00H-7FH] 
Block Type: EDID 1.3 

EDID Block 1, Bytes 128-255  [80H-FFH] 
Block Type: CEA EDID Timing Extension Version 3 

5) RGB [C/S: 36FF] 

EDID Block 0, Bytes 0-127 [00H-7FH] 
Block Type: EDID 1.3 

* don’t push The INSTOP KEY after completing the function

inspection.    

5.1.1 Overview

•W/B adj.: Objective & How-it-works
- Objective: To reduce each Panel’s W/B deviation
- How-it-works: When R/G/B gain in the OSD is at 192, it
means the panel is at its Full Dynamic Range. In order to
prevent saturation of Full Dynamic range and data, one of
R/G/B is fixed at 192, and the other two is lowered to find the
desired value.

5.1.2 Equipment

1) Color Analyzer : CA-210 (NCG: CH 9 / WCG: CH12 /LED
Module:CH14)
2) Adjustment Computer (During auto adj., RS-232C protocol
is needed)
3) Adjustment R/C
4) Video Signal Generator MSPG-925F 720p/216Gray
(Model:217, Pattern:78)
-> Only when internal pattern is not available
• Color Analyzer Matrix should be calibrated using CS-1000

5.1.3 Equipment connection map

• Protocol
<Command Format>

- LEN: Number of Data Byte to be send
- CMD: Command
- VAL: FOS Data
- CS: Checksum of sent Data
- A: Acknowledge
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]

- 13 -

Color Analyzer

Computer

RS-232C

# Pattern Generator

* If TV internal pattern is used,not needed

Signal Source

Probe

RS-232C

RS-232C

START     6E    A     50    A

      LEN    A    03    A

      CMD    A    00    A

      VAL    A    CS    A

STOP 

• RS-232C Command used during auto-adjustment

Ex) wb 00 00 -> Begin white balance auto-adj.

wb 00 10 -> Gain adj.
ja 00 ff -> Adj. data
jb 00 c0
...
...
wb 00 1f -> Gain adj. complete
*(wb 00 20(Start), wb 00 2f(End)) -> Off-set adjustment

wb 00 ff -> End white balance auto-adjustment

• Adj. Map 

- Applied models: models with LA92S Chassis 

5.1.4 Adjustment method

5.1.4.1 Auto adjustment method

1) Set TV in adj. mode using POWER On Key

2) Zero calibrate probe then place it on the center of the

Display

3) Connect Cable(RS-232C)
4) Select mode in adj. Program and begin adj.
5) When adj. is complete (OK Sign), check adj. status per

mode (Warm, Medium, Cool)

6) Remove probe and RS-232C cable to complete adj.

- Adj. must begin w/ command “Wb 00 00”, and end w/”wb 00

ff” and adjustment offset if needed.

5.1.4.2 Manual adj. method

Dynamic contrast : off
Dynamic color : off
OPC : Off
Energy saving mode : Off

5.1.4.3 Adjustment 

1) Set TV Picture Mode to Standard and in Advanced

Control, set Dynamic Contrast and Color ‘Off’, OPC ‘OFF’. 

2) Set TV in adj. mode using POWER On Key 
3) Press ADJ key ->  EZ adjust using adj. R/C 
4) Using CH + / - KEY, select 10.TEST PATTERN then press

Enter to place in HEAT RUN mode  and wait for 30
minutes. 

5) Zero calibrate the probe of Color Analyzer, then place it on

the center of LCD module within 10 cm of the surface. 

6) Press ADJ key  7. White-Balance then press the cursor to

the right (KEY

)

(When 

is pressed Full White internal pattern will be

displayed)

7) One of R Gain / G Gain / B Gain should be fixed at 192,

and the rest will be lowered to meet the desired value. 

8) Adj. is performed in COOL, MEDIUM, WARM 3 modes of

color temperature 

• Adjustment condition and cautionary items

1) Lighting condition in surrounding area Surrounding lighting

should be lower than 10 lux.

Try to isolate adj. area into dark surrounding.

2) Probe location

- Color Analyzer (CA-210) probe should be within 10cm

and perpendicular of the module surface (80°~ 100°)

- B/L on should be checked using no signal or Full white

Pattern

- 14 -

CMD

ID DATA

Explanation

wb 

00 

00 

Begin White Balance adj.

wb

00 

ff

End White Balance adj. 

(internal pattern disappears)

- 15 -

5.1.5 Reference 

(White Balance adj. coordinate and color temperature)

• Luminance: Full white 216 Gray
• Standard color coordinate and temperature using CS-1000

• Standard color coordinate and temperature using CA-210(CH 09) 

5.2.1 Overview

America due to rating

• Applied model: LA92S Chassis applied None USA

Model(Canada, Mexico)

5.2.2 Method

1) Press ADJ key on the Adjustment R/C, then select Country

Group Menu

2) Depending on destination, select KR or US, then on the

lower option, select US, CA, MX. Selection is done using  +,
- KEY

Step 1) Turn on TV
Step 2) Press EYE key of Adj. R/C
Step 3) Cover the Eye Q II sensor on the front of the using

your hand and wait for 6 seconds

Step 4) Confirm that R/G/B value is lower than 10 of the “Raw

Data (R: G: B: )” .

If after 6 seconds, R/G/B value is not lower than 10,
replace Eye Q II sensor

Step 5) Remove your hand from the Eye Q II sensor and wait

for 6 seconds

Step 6) Confirm that “B. Light(xxx)” value increases from 0.

If change is not seen, replace Eye Q II sensor

< step 2>                     < step 3>                   < step 4>

< step 5>                  < step 6>

After final inspection, press In-Stop key of the Adj. R/C and
check that the unit goes to Stand-by mode.  

6.1 Method

- Check that Power Cord is fully inserted to the set

(If loose, re-insert)

- Unit w/ fully inserted power cord and A/V arrives to the auto-

check process.

- Connect D-terminal AV JACK TESTER
- Auto CONTROLLER(GWS103-4) ON
- Perform GND TEST
- If NG, Buzzer will sound to inform the operator
- If OK, changeover to I/P check automatically

(Remove CORD,A/V from AV Jack Box)

- Perform I/P test
- If NG, Buzzer will sound to inform the operator
- If OK, Good lamp will lit up and the stopper will allow the

pallet to move on to next process.

6.2 Checkpoint

NEUTRAL

• LEAKAGE CURRENT: At 0.5mArms

Coordinate 

Mode 

x y 

Temp uv

∆

Cool 0.269±0.002 0.273±0.002 13000K 0.0000

Medium 0.285±0.002  0.293±0.002 

9300K 

0.0000

Warm 0.313±0.002  0.329±0.002  6500K  0.0030

Green Eye-Check 

Sensor Data:

      1 

Backlight:     0

 

O.K 

Green Eye-Check 

Sensor Data:   215 

Backli ght :     100 

Coordinate 

Mode 

x y 

Temp uv

∆

Cool 0.269 0.273  13000K  0.0000

Medium 0.285  0.293 

9300K 

0.0000

Warm 0.313  0.329 

6500K  0.0030

- 16 -

300

500

510

310

560

120

122

200

801

540

530

803

802

550

810

910

920

900

400

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These

parts are identified by       in the Schematic Diagram and EXPLODED VIEW. 

It  is  essential  that  these  special  safety  parts  should  be  replaced  with  the  same  components  as

recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. 

Do not modify the original design without permission of manufacturer.

A2

LV1

A10

LV2

A23

305