DOWNLOAD LG 32LG700H (CHASSIS:LA80A) Service Manual ↓ Size: 7.21 MB | Pages: 41 in PDF or view online for FREE

- 9 -

This specification sheet is applied for all of the LCD TV with
LA80A chassis.

(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation
transformer will help protect test instrument.

(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of

25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.

(4) The input voltage of the receiver must keep 100~120V,

50/60Hz.

(5) The receiver must be operated for about 5 minutes prior to

the adjustment.

* After RGB Full White in HEAT-RUN Mode, the receiver

must be operated prior to the adjustment.

* Enter into HEAT-RUN MODE

1) Press the POWER ON KEY on R/C for adjustment.
2) OSD display and screen display 100% full WHITE
PATTERN.

* Set is activated HEAT run without signal generator in this

mode. 

* Single color pattern (RED / BLUE / GREEN) of HEAT

RUN MODE uses to check panel. 

* Caution: If you turn on a still screen more than 20

minutes (Especially digital pattern, cross hatch pattern :
13CH), an after image may be occur in the black level
part of the screen.

(1) Connect port(3) with Power Code 
(2) Connect jack(1) with PTC Micom.
(3) Connect USB Cable to the computer 
(4) Download Program execution (SAP Configuration) 

* Notice!

Because PTC Download JIG has internal memory, it can
save download files using download program (SAP
Configuration). Push the START button (4) after file saving,
then it execute download. 

(SAP Configuration)

(1) Select HCS12
(2) Target Frequency Settings : 

1) Checking the factor -> Use Specified Target

Frequency…, Unsecured target….

2) Insert Target Bus Frequency -> 7372800

(3) Specify Algorithm: 9S12dt128_128k .12P
(4) Specify S Record: select download file. 
(5) Checking factor: Erase Device, Blank Check Device,

Program Device, Verify Device 

* Notice!

Don’t check other checking boxes. You must follow fig.

(6) Push the ‘Save Image to Cyclone PRO’ button, files

transfer from PC to the Download JIG.

4. Start button

3. Power

1. Connect to Micom port of TV board.

2. Connect to computer.

3

4

 

1

2

5

6

- 10 -

- Using equipment : PC, download JIG cable(Alter Byteblaster cable)

(1) Connect the JIG cable between computer and Main

board(P1500)

(2) Connect the power cable of Main board and Turn on the

Main power.

(3) Launch the download program(QuartusII 6.1 programmer)

in the Computer.

(4) Setting the environment feature of the download program

(5) Click  the “Add File...” menu and select the download

file(dvi_12to24.pof) in your PC.

(6) Check the “Program/Configure” and “Verify” box and then

click “Start” button

(7) Without any problem, you can see the normal status of the

progress bar

Main B/D

JIG cable(CPLD D/L)

 

- 11 -

- System control RS-232 Host should be “PC” for adjustment.

Refer to the “6.1.2 Procedure of Adjustment” and adjust
three items of ADC on PCB Ass’y level through the RS-
232C.

** ADC adjustment RS232C Protocol Ver 1.0

* Baud Rate : 115,200 bps
* RS232C Host : PC
* echo : None

(1) Requirement for Adjustment

- Pattern Generator : MSPG-925FA
- Adjust 480i Comp1(Model : 209, Pattern : 65)
- Adjust 1080p Comp1 / RGB(Model : 225, Pattern : 65)

(2) Adjustment Procedure

- ad 00 00  Entering ADC Adjustment Mode
- kb 00 04  Component1 Input Change
- ad 00 10  Adjust 480i Comp1
- kb 00 06  RGB-DTV Input Change
- ad 00 10  Adjust 1080p Comp1/RGB
- ad 00 90  Finish adjustment

For downloading the MAC address which be allotted on each
LAN Card.

(1) Adjustment Method

1) Connecting the TV set and the PC which has MAC

Address Writing program through the RS232C cable.

2) Editing the mac address.txt

(Inserting start MAC address at top low.

Inserting start MAC address at bottom low.
Launch MAC Address Writing program and set just like
below picture. - (1)

3) Click the LOAD button for reading the MAC address.- (2)

(SAVE : Saving the current MAC Address

CLEAR : Initializing the space which insert MAC Address.

4) Click the “MAC Address writing” button to write current

MAC Address.- (3)

5) In case of being downloaded normally, you can see the

“OK” message in the window. - (4)

6) In case of being downloaded normally, MAC address

increased one by one automatically. So the next set, just
click the “MAC Address writing” button after connecting
the port.

(Whenever be finished, the program saves the MAC
Address in “mac address.txt” file automatically.)

* For confirm works normally the LAN card through PING TEST.

(1) Adjustment Method (PCB Ass’y Level)

1) Connecting the LAN to Ass’y and then turn on the Power.

(Default IP Setting is “Automatic setting” and allocated
the IP from Router each Power ON time automatically.)

2) Press the ADJ Key in the adjustment remote controller.
3) Press the “11. ACAP PING TEST” in EZ ADJUST menu

to check the Network works well. 

In case of normal status, you can see the “Network is
normal” message. 
And abnormal case, you can see “Network is not normal”
message.

480i Component

1080p Component / RGB

MSPG-925FA

Model No : 209

Pattern No : 65

Model No : 225

Pattern No : 65

Procedure

Command

Set Act

1. Entering ADC mode ad 00 00 d 00 OK00x

2. Input change

kb 00 01

b 00 OK01x (Adjust RF and Video)

kb 00 04

b 00 OK04x (Adjust 480i Comp1)

kb 00 06  b 00 OK06x (Adjust 1080p Comp1/RGB)

3. Start ADC

ad 00 10

4. Result return

OKx (Success)

NGx ( Fail )

5. Data read

( main)

(main)

ad 00 20 000000000000000000000000007c007b006dx

( sub )

(Sub)

ad 00 21 000000070000000000000000007c00830077x

6. Data confirm

ad 00 99 NG 03 00x (Fail)

NG 03 01x (Fail)

NG 03 02x (Fail)

OK 03 03x (Success)

7. Finish ADC

ad 00 90 d 00 OK90x

 

( 1) 

(2) 

(3) 

(4) 

- 12 -

(2) Adjustment Method (Ass’y Line Level)

1) Connecting the LAN port in SET to the PC which has the

PING Test program through a Cross LAN Cable. (PC
LAN IP setting : 12.12.2.3)

2) Launch the PING Test program and confirm the program

Setting.

(Checking the TV’s IP is set 12.12.2.2 in program. Don’t
check the Modem.)

3) Press the Power Only Key in the adjustment remote

controller. (Setting the TV IP)

4) Click the “RUN” button of program, and then program

display “OK” or “NG” like a below picture.

* For clear the IP setting after the adjustment, press the

INSTOP button.

(1) Required Equipment

- Remote controller for adjustment 
- AV Pattern Generator: 801GF(802B, 802F, 802R), Master

(MSPG-925FA), etc

(Which has 480i/1080p Horizontal 100% Color Bar
Pattern with 0.7±0.1 Vpp level. See Fig. 1)

- It is very import to use correct adjustment pattern like

Fig.1.

(2) Method of Adjusting 480i Comp1, 1080p Comp1 / RGB

Color Balance

1) Checking the connection of TV set and Pattern

Generator. 

-> MSPG-925FA, Model No : 209,  Pattern No: 65 

2) Set the TV source to Component and input the 100%

Horizontal Color Bar Pattern(HozTV31Bar), and finally
select picture mode to ‘Normal’(standard).

3) After receiving the signal, Press ADJ key on R/C for

adjustment.

4) Select the 1. Adjust 480i Comp1 and press the 

G

(Vol. +)

or Enter key operate to set, and then it becomes
automatically.

5) “ADC Component1 Success” means completed

adjustment.

6) If abnormal case, TV display the message “ADC

Component1 480i Fail”

7) Checking the connection of TV set and Pattern Generator.

-> MSPG-925FA, Model No : 225,  Pattern No: 65

8) Set the TV source to Component and input the 100%

Horizontal Color Bar Pattern(HozTV31Bar) of 1080p
mode, and finally select picture mode to ‘Normal’
(standard).

9) After receiving the signal, Press ADJ key on R/C for

adjustment

10) Select the 2. Adjust 1080p Comp1 / RGB and press

the 

G

(Vol. ±) or Enter key operate to the set, and then

it becomes automatically

11) In case of normal status “ADC Component1 Success”

means completed adjustment.

And abnormal status “ADC Component1 1080p Fail”

12) After adjusting the Comp1, TV source will be changed

RGB DTV mode. 

Then Adjustment will be automatically done.

13) “ADC RGB 1080p Success” means completed

adjustment.

14) After finish adjustment, press the ADJ key and quit the

adjustment menu.

(1) Required Test Equipment

1) Adjusting PC with S/W for writing EDID Data.
2) A Jig for EDID Download
3) Cable: Serial (9Pin or USB) to D-sub 15Pin cable, D-sub

15Pin cable, DVI to HDMI cable.

(2) Setting of device

1) When input HDMI EDID data through RGB or HDMI

jack, writing 8bits of the data at every turn with “DDC2B”
protocol.

<Fig. 1. Adjust Pattern : 480i/ 1080p 60Hz pattern>

<Fig. 4 Connection Diagram of DDC download>