DOWNLOAD LG 32LC7D (CHASSIS:LA73E) Service Manual ↓ Size: 14.71 MB | Pages: 45 in PDF or view online for FREE

- 13 -

7. EDID(The Extended Display 

This is the function that enables “Plug and Play".

1) PC, Jig for adjusting DDC. (PC serial to D-sub

Connection equipment)

2) S/W for writing DDC(EDID data write & read)
3) D-Sub cable
4) Jig for HDMI Cable connection

1) Set devices as below and turn on the PC and JIG.
2) Open S/W for writing DDC (EDID data write & read).

(operated in DOS mode)

O

EDID for HDMI-1 (DDC (Display Data Channel) Data)

EDID Block 0 table =

EDID Block 1 table =

O

EDID for HDMI-2 (DDC (Display Data Channel) Data)

EDID Block 0 table =

EDID Block 1 table =

O

EDID for RGB-PC

EDID Block 0 table =

  0   |  00  FF  FF  FF  FF  FF  FF  00  1E  6D  01  00  01  01  01  01

 10  |  00  11  01  03  80  73  41  96  0A  CF  74  A3  57  4C  B0  23

 20  |  09  48  4C  2F  CE  00  31  40  45  40  61  40  01  01  01  01

 30  |  01  01  01  01  01  01  66  21  50  B0  51  00  1B  30  40  70

 40  |  36  00  C4  8E  21  00  00  1E  0E  1F  00  80  51  00  1E  30

 50  |  40  80  37  00  C4  8E  21  00  00  1C  00  00  00  FD  00  38

 60  |  4B  1F  3C  09  00  0A  20  20  20  20  20  20  00  00  00  FC

 70  |  00  4C  47  20  54  56  0A  20  20  20  20  20  20  20  01  98

  0  |  02  03  16  F1  46  84  05  03  02  20  22  23  15  07  50  66

 10  |  03  0C  00  10  00  80  01  1D  00  72  51  D0  1E  20  6E  28

 20  |  55  00  C4  8E  21  00  00  1E  01  1D  80  18  71  1C  16  20

 30  |  58  2C  25  00  C4  8E  21  00  00  9E  8C  0A  D0  8A  20  E0

 40  |  2D  10  10  3E  96  00  C4  8E  21  00  00  18  8C  0A  D0  8A

 50  |  20  E0  2D  10  10  3E  96  00  13  8E  21  00  00  18  00  00

 60  |  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00

 70  |  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  25

  0  |  00  FF  FF  FF  FF  FF  FF  00  1E  6D  01  00  01  01  01  01

 10  |  00  11  01  03  80  73  41  96  0A  CF  74  A3  57  4C  B0  23

 20  |  09  48  4C  2F  CE  00  31  40  45  40  61  40  01  01  01  01

 30  |  01  01  01  01  01  01  01  1D  00  72  51  D0  1E  20  6E  28

 40  |  55  00  C4  8E  21  00  00  1E  01  1D  80  18  71  1C  16  20

 50  |  58  2C  25  00  C4  8E  21  00  00  9E  00  00  00  FC  00  4C

 60  |  47  20  54  56  0A  20  20  20  20  20  20  20  00  00  00  FD

 70  |  00  38  4B  1F  3C  09  00  0A  20  20  20  20  20  20  01  66

  0  |  02  03  16  F1  46  84  05  03  02  20  22  23  15  07  50  66

 10  |  03  0C  00  20  00  80  8C  0A  D0  8A  20  E0  2D  10  10  3E

 20  |  96  00  C4  8E  21  00  00  18  8C  0A  D0  8A  20  E0  2D  10

 30  |  10  3E  96  00  13  8E  21  00  00  18  00  00  00  00  00  00

 40  |  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00

 50  |  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00

 60  |  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00

 70  |  00  00  00  00  00  00  00  00  00  00  00  00  00  00  00  B3

  0  |  00  FF  FF  FF  FF  FF  FF  00  1E  6D  01  00  01  01  01  01

 10  |  00  11  01  03  68  73  41  96  0A  CF  30  A3  57  4C  B0  23

 20  |  09  50  4E  A1  08  00  01  01  01  01  01  01  01  01  01  01

 30  |  01  01  01  01  01  01  66  21  50  B0  51  00  1B  30  40  70

 40  |  36  00  C4  8E  21  00  00  1E  0E  1F  00  80  51  00  1E  30

 50  |  40  80  37  00  C4  8E  21  00  00  1C  00  00  00  FD  00  38

 60  |  4B  1F  3C  09  00  0A  20  20  20  20  20  20  00  00  00  FC

 70  |  00  4C  47  20  54  56  0A  20  20  20  20  20  20  20  00  D0

LCD TV SET

(or Digital Board)

- 14 -

(1) Purpose: to reduce the difference in color temperature

among modules

(2) Principal: A module is in full dynamic range when RGB

Gain on OSD is 192. To adjust the white balance without
causing full dynamic range and full data, fix one of RGB
Gains at 192 and control the other two by reducing them
from 192.

(1) Color Analyzer : CA-110  or CA-210

(2) Automatic adjustor (with automatic adjustment necessity

and the RS-232C communication being possible)

(Automatic Adjustment)

Use the internal pattern to adjust White Balance. The pattern
is automatically given when the automatic adjustment device
is connected or when a user presses ADJ on the remote
controller to start Ez Adjust and then selects 6.White-Balance.

* Requirements for Automatic Adjustment

(1) The illuminance of surroundings

10 lux or less; preventing light in surroundings as much as
possible

(2) The location of the Probe

1) For PDP: place the color analyzer (CA-110, CA-210)

close to the surface of a module and start the
adjustment.

2) For LCD: place the color analyzer (CA-110, CA-210)

close to the surface of a module within 10 cm and keep
the probe of the color analyzer at 80° to 100° angle from
the surface of a module.

(3) Aging time

1) Once Aging is started, keep the power on without power

supply interruption for at least 15 minutes for heat run.

2) For PDP, use the internal pattern to adjust White

Pattern.

3) For LCD, use NO SIGNAL or Full White Pattern to

ensure the backlight is turned on.

(Automatic Adjustment)

(1) Turn on the POWER ON(

Â

) of the remote controller to set

the adjustment and then start the automatic adjustment or
set the Baud Rate to 115200.Â) of the remote controller to 

(2) Start the adjustment from “wb 00 00” and complete it at

“wb 00 ff”. (Adjust the offset if necessary)

wb 00 00 the automatic adjustment of White Balance is
started.
wb 00 10 adjusting gain (internal pattern appears) is
started.
ja 00 ff adjusting data
jb 00 c0
...
wb 00 1f adjusting gain is completed.
Adjust the offset (from wb 00 20 to wb 00 2f) if necessary.
wb 00 ff the automatic adjustment of White Balance
(internal pattern disappears) is completed.

C A -100+

C O L O R

A N A L Y Z E R

T Y P E ; C A -100+

F u l l W h i t e P at t er n

R S-232C

Connection Diagram of Automatic Adjustment

- 15 -

(Automatic Adjustment)

LA73E Chassis Model All]

(Manual Adjustment)

Required Equipment :  CA-210 

(1) Enter ‘Ez - Adjust’ by pressing ADJ KEY on the Service

Remote Control.

(2) Select "9. TEST PATTERN" using CH +/- Key and HEAT

RUN at least 30 minutes by pressing the ENTER Key.

(3) Zero Calibrate of the Color Analyzer, then attach sensor to

LCD module surface when you adjust.

(4) Select ‘6. White-Balance’ of ‘Ez - Adjust’ by pressing the

ADJ KEY on the Service R/C. Then enter adjustment mode
by pressing the Right KEY (G) .
(The internal pattern of full white appears by pressing G)

(5) The adjustment is conducted in three levels of color

temperature; COOL, MEDIUM, and WARM.

* Color temperature: Cool, Medium, Warm

(1) When R Gain is fixed at 192,

Control G Gain and B Gain by reducing them from 192.

(2) When B Gain is fixed at 192,

Control R Gain and G Gain by reducing them from 192.

(3) When G Gain is fixed to 192,

Control R Gain and B Gain by reducing them from 192.

Fix one of three Gains (R Gain, G Gain, and B Gain) at 192
and control the other two by reducing values from 192 to
prevent it from increasing.

(When RGB Gains are all 192, the module is in full dynamic
range.)

USB Download enables quick response to S/W upgrading and
helps to configure the panel to the latest updates.

(1) Before starting USB download, ensure that the power is

turned off and the display is turned on.

(2) Once the USB memory stick containing the upgraded file

is connected to the USB port on the main board, the
following picture appears on the screen.

(3) Check the current version at [Current TV Software Version

Information] and the target version at [New Found TV
Software Version Information]. Press Enter on the remote
controller to confirm the upgrade.

(4) The following picture shows the downloading in progress.

Once the download is completed, the power is
automatically turned on and off. (Otherwise, please turn the
power on and off)

(5) Once the download is completed, remove the USB

memory stick from the USB port. Press IN-START on the
remote controller to check the upgraded S/W version at the
top of the screen while the display is turned on.

R Gain

G Gain

B Gain

R Cut

G Cut

B Cut

jg

jh

ji

Cool

ja

jb

jc

Mid

RS-232C COMMAND

[CMD ID DATA]

CENTER

(DEFAULT)(Decimal)

jd

je

jf

00

00

00

192

192

192

Warm

Min

Max

(Deci

mal)

64

64

64

Cool

64

64

64

Mid

64

64

64

Warm

   

Do not plug off.

Press EXIT to cancel the upgrade.

<S/W Upgrade Screen>

The software upgrade is now in progress.

Until the whole process if completed, please.

- Do not remove the memory card from the slot.

- Do not plug off.

Reading the file---Done

Upgrading---Done

The TV will restart automatically in 0 seconds.

<Downloading in progress Screen>

- 16 -

No

RGB DTV

Yes

Adaptiv e Picture  Mode

¥Audio Outp ut 
10W*2

¥Freeze No

Oth ers

Phase, Siz eAdjust

DOS70,VGA60,S

VGA60,

XGA60,WXGA60,

SXGA60

RGB In  (15 Pin)

Yes

Auto Nav igation (Link)

Yes

BBE

Yes

SRS Trusur round TX

Yes(2D)

Enhance d Noise  Reductio n

USE scalie r On/Off OSD Menu

Yes

XD Engine

Use B rief Inf o

O(PSIP)

Progr am Gui de Type

1 RF

1 RF(Air  /Cable)

RF

Remark

Broadcom

Feature

- Prouct Brief spec