DOWNLOAD LG TS-H076JSA0 / S07LHK Service Manual ↓ Size: 46.33 MB | Pages: 118 in PDF or view online for FREE

Model
TS-H076JSA0 S07LHK
Pages
118
Size
46.33 MB
Type
PDF
Document
Service Manual
Brand
Device
Air Conditioner
File
ts-h076jsa0-s07lhk.zip
Date

LG TS-H076JSA0 / S07LHK Service Manual ▷ View online

8
mm
inch
kg.m
Ø6.35
1/4
1.8
Ø9.52
3.8
4.2
Ø12.7
1/2
5.5
Ø15.88
5/8
6.6
Ø19.05
3/4
6.6
Outside diameter
Torque
Tape the drain hose and the connecting cable.
• Connecting cable
Indoor unit installation
■ 
Hang the indoor unit from the hooks at the top of
the installation plate.
■ 
Insert the spacer etc. between the indoor unit and
the installation plate and separate the bottom of
the indoor unit from the wall.
Route the indoor tubing and the drain hose to the
required piping hole position.
A
Insert the piping, drain hose, and the connecting
cable into the piping hole.
B
D
E
Insert the connecting cable into the indoor unit.
■ 
Don't connect the cable to the indoor unit.
Make a small loop with the cable for easy connection
later.
C
Drain pipe
Connecting cable
Bundle the piping and drain hose together by
wrapping them with vinyl tape for enough to cover
where they fit into the rear piping housing section.
Installation plate
Spacer
Indoor unit
8cm
Connecting the pipings to the indoor unit and
the drain hose to drain pipe.
Align the center of the pipes and sufficiently
tighten the flare nut by hand.
Tighten the flare nut with a wrench.
F
Wrap the insulation material around the
connecting portion.
■ 
Overlap the connection pipe heat insulation and the
indoor unit pipe heat insulation material. Bind them
together with vinyl tape so that there is no gap.
G
Plastic bands
Insulation material
Indoor unit tubing
Flare nut
Pipes
Wrench
Indoor unit tubing
Connection pipe
Flare nut
Open-end wrench (fixed)
Vinyl tape
Adhesive
Drain hose
Indoor unit drain hose
(narrow)
When extending the drain hose at the indoor unit,
install the drain pipe.
For left rear piping 
Wrap with vinyl tape
Drain hose
Pipe
Vinyl tape(wide)
ENGLISH
9
Installation Information (For left piping)
• Good case
For left piping. Follow the instruction below.
■ 
Press on the upper side of clamp. ( )
■ 
Unfold the tubing to downward slowly. ( )
■ 
Bend the tubing to the left side of chassis.
Vinyl tape(narrow)
Connection
pipe
Connecting cable
Indoor 
unit piping
Pipe
Vinyl tape
(wide)
Wrap with vinyl tape
Wrap the area which accommodates the rear
piping housing section with vinyl tape.
Drain hose
Vinyl tape(narrow)
Pipe
Wrap with 
vinyl tape(wide)
Bundle the piping and drain hose together by
wrapping them with cloth tape over the range
within which they fit into the rear piping housing
section.
Reroute the pipings and the drain hose across
the back of the chassis.
Set the pipings and the drain hose to the back of
the chassis with the tubing holder.
Hook the edge of tubing holder to tap on chassis
and push the bottom of tubing holder to be
engaged at the bottom of chassis.
H
Indoor unit installation 
Remove the spacer.
Ensure that the hooks are properly seated on the
installation plate by moving it left and right.
J
Drain hose
Connecting
cable
Piping for
passage through
piping hole
Tubing holder
I
Press the lower left and right sides of the unit against
the installation plate until the hooks engage into their
slots(clicking sound).
CAUTION
Page of 118
Display

Click on the first or last page to see other TS-H076JSA0 / S07LHK service manuals if exist.