LG LWG0760AHG_AHN_AHE Service Manual ▷ View online
—14—
3. INSTALLATION
3.1 SELECT THE BEST LOCATION
1.To prevent vibration and noise, make sure the unit
is installed securely and firmly.
2.Install the unit where the sunlight does not shine
directly on the unit.
3.The outside of the cabinet must extend outward for
at least 11" and there should be no obstacles, such
as a fence or wall, within 20" from the back of the
cabinet because it will prevent heat radiation of the
condenser.
Restriction of outside air will greatly reduce the
cooling efficiency of the air conditioner.
as a fence or wall, within 20" from the back of the
cabinet because it will prevent heat radiation of the
condenser.
Restriction of outside air will greatly reduce the
cooling efficiency of the air conditioner.
4.Install the unit a little slanted so the back is slightly
lower than the front (about
1
/
2
"). This will help force
condensed water to the outside.
5.Install the unit from the bottom about 30"~60"
above the floor level.
All side louvers of the cabinet must remain
exposed to the outside of the structure.
exposed to the outside of the structure.
AWNING
COOLED AIR
HEAT
RADIATION
30"~60"
ABOUT
1
/
2
"
Over 20"
FENCE
Figure 18
CAUTION
3.2 HOW TO INSTALL
SUGGESTED TOOL REQUIREMENTS
PREPARATION OF CHASSIS
1. Before installing the room air conditioner, please
install the knob. (If it is not fixed on the unit.)
2. Remove the screws which fasten the cabinet at
both sides and at the back.
3. Slide the unit from the cabinet by gripping the base
pan handle and pulling forward while
bracing the cabinet.
bracing the cabinet.
4. Slide the air conditioner into the case.
Reinstall the 2 screws removed earlier on each side
of the case.
of the case.
CAUTION: The power cord must be connected to an independent
circuit. The green wire must be grounded.
Shipping
screws
SCREWDRIVER(+, -), RULLER, KNIFE, HAMMER, PENCIL, LEVEL
Figure 19
Figure 20
Figure 21
—15—
5. Stuff the foam between the top of the unit and the
wall to prevent air and insects from getting into the
room.
room.
6. Attach the front grille to the case by inserting the
tabs on the grille into the slots on the front of the
case. Push the grille in until it snaps into place.
case. Push the grille in until it snaps into place.
When you detach the front grille from the case,
push the grille to your right side and pull it toward
you.
push the grille to your right side and pull it toward
you.
7. Lift the inlet grill and secure the front grille with a
screw. Lower the inlet grille into place.
(In case of some models, you can secure the front grille
from the right side or lower side.)
(In case of some models, you can secure the front grille
from the right side or lower side.)
3.3 HOW TO USE THE
REVERSIBLE INLET GRILLE
1. If you want to pull out the filter upward, open the
inlet grille slightly. Turn inside out the front grille.
Disassemble the inlet grille from the front grille with
separating the hinged part by inserting a "—" type
screw-driver tip.
Rotate the inlet grille 180 degrees and insert the
hooks into the lower holes of front grille.
Then, insert the filter (See Figure 26, 27)
Disassemble the inlet grille from the front grille with
separating the hinged part by inserting a "—" type
screw-driver tip.
Rotate the inlet grille 180 degrees and insert the
hooks into the lower holes of front grille.
Then, insert the filter (See Figure 26, 27)
Inlet Grille
Figure 24
Figure 25
Figure 26
Figure 27
Figure 22
Figure 23
—16—
2. Attach the front grille to the cabinet by inserting the
tabs on the grille into the tabs on the front of the
cabinet. Push the grille in until it snaps into place.
(See Figue 28)
cabinet. Push the grille in until it snaps into place.
(See Figue 28)
3. Lift the inlet grille and secure it with a type A screw
through the front grille.
(See Figure 29)
(See Figure 29)
4. If you want to pull out the filter downward, use the
reversible inlet grille without change.
(The grille is already assembled for that way.)
(The grille is already assembled for that way.)
Figure 28
Figure 29
4. TROUBLESHOOTING GUIDE
4.1 OUTSIDE DIMENSIONS
unit: mm(inch)
353(13
7
/
8
")
470(18
1
/
2
")
525(20
11
/
16
")
—16—
2. Attach the front grille to the cabinet by inserting the
tabs on the grille into the tabs on the front of the
cabinet. Push the grille in until it snaps into place.
(See Figue 28)
cabinet. Push the grille in until it snaps into place.
(See Figue 28)
3. Lift the inlet grille and secure it with a type A screw
through the front grille.
(See Figure 29)
(See Figure 29)
4. If you want to pull out the filter downward, use the
reversible inlet grille without change.
(The grille is already assembled for that way.)
(The grille is already assembled for that way.)
Figure 28
Figure 29
4. TROUBLESHOOTING GUIDE
4.1 OUTSIDE DIMENSIONS
unit: mm(inch)
353(13
7
/
8
")
470(18
1
/
2
")
525(20
11
/
16
")
Click on the first or last page to see other LWG0760AHG_AHN_AHE service manuals if exist.