DOWNLOAD LG LWG0760AHG_AHN_AHE Service Manual ↓ Size: 2.87 MB | Pages: 60 in PDF or view online for FREE

—6—

1. Open the lnlet grille upward or downward.
2. Remove the screw which fastens the front grille.
3. Pull the front grille from the right side.
4. Remove the front grille.
5. Re-install the component by referring to the

removal procedure, above.(See Figure 1)

1. After disassembling the FRONT GRILLE, remove

the 2 screws which fasten the cabinet at both
sides.

2. Remove the 2 screws which fasten the cabinet at

back.

3. Pull the base pan forward. (See Figure 2)
4. Remove the cabinet.
5. Re-install the component by referring to the

removal procedure, above.

1. Disconnect the unit from the power source.
2. Remove the front grille. (Refer to section 2.1.1)
3. Remove the cabinet. (Refer to section 2.1.2)
4. Remove the screw which fastens the control box

cover.

5. Remove the housing which connects motor wire

in the control box.

6. Remove the 3 leads from the compressor.

(Refer to section 2.3.1)

7.Discharge the capacitor by placing a 20,000

ohmresistor across the capacitor terminals.

8. Remove the 2 screws which fasten the control

box.(See Figure 3)

9. Pull the control box forward completely.

10. Re-install the components by referring to the

removal procedure, above. (See Figure 3)
(Refer to the circuit diagram found on page 24 in
this manual or on the control box.)

— Before the following disassembly, POWER SWITCH set to OFF and disconnect the power cord.

—7—

1. Remove the front grille. (Refer to section 2.1.1)

2. Remove the cabinet. (Refer to section 2.1.2)

3. Remove the control box. (Refer to section 2.1.3)

4. Remove the 3 screws which fasten the brace.

5. Remove the brace.

6. Remove the 2 screws which fasten the evaporator.

7. Move the evaporator forward and pulling it upward

slightly. (See Figure 4)

8. Move the evaporator to the left carefully. 

9. Pull out the hook of orifice by pushing the tabs and

remove it. (See Figure 5)

10. Remove the clamp with a hand plier which

secures the blower.

11. Remove the blower.
12. Remove the 4 screws which fasten the air guide

from the barrier.

13. Move the air guide backward, pulling out from the

base pan.

14. Re-install the components by referring to the

removal procedure, above. 

1. Remove the cabinet. (Refer to section 2.1.2)

2. Remove the brace (Refer to section 2.2.1)

3. Remove the 3 screws which fasten the condenser.

4. Move the condenser to the left carefully.

5. Remove the clamp which secures the fan.

6. Remove the fan and then pull out the shroud. 

(See Figure 6)

7. Re-install by referring to the removal procedure. 

—8—

1. Remove the cabinet. (Refer to section 2.1.2)

2. Remove the nut which fastens the terminal cover.

3. Remove the terminal cover. (See Figure 7)

4. Remove all the leads from the overload protector.

5. Remove the overload protector.

6. Re-install the component by referring to the

removal procedure, above. 

1. Remove the cabinet. (Refer to section 2.1.2)

2. Discharge the refrigerant system using a Freon

TM

Recovery System.
If there is no valve to attach the recovery system,
install one (such as a WATCO A-1) before venting
the Freon

TM

. Leave the valve in place after 

servicing the system.

3. Remove the overload protector. (Refer to section

2.3.1)

4. After purging the unit completely, unbraze the

suction and discharge tubes at the compressor
connections.

5. Remove the 3 nuts and the 3 washers which 

fasten the compressor.

6. Remove the compressor. (See Figure 8)

7. Re-install the components by referring to the

removal procedure, above.

—9—

1. Remove the control box. (Refer to section 2.1.3)
2. Remove the knobs and the screw which fasten

control panel from control box.

3. Remove the screw which located in the front.
4. Open the bottom side of control box.
5. Remove the screw and the clamp which fastens the

capacitor.

6. Disconnect all the leads of capacitor terminals.
7. Re-install the components by referring to the

removal procedure, above. (See Figure 9)

1. Remove the control box. (Refer to section 2.1.3)
2. Open the control box. (Refer to section 2.3.3)
3. Disconnect the grounding screw from the control

box.

4. Disconnect the 2 receptacles.
5. Remove a screw which fastens the clip cord. 

(See Figure 10)

6. Remove the power cord. 
7. Re-install the component by referring to the above

removal procedure, above.
(Use only one ground-marked hole      for ground
connection.)

8. If the supply cord of this appliance is damaged, it

must be replaced by the special cord. (The 
special cord means the cord which has the same
specification marked on the supply cord attached at
the unit.)

1. Remove the control box. (Refer to section 2.1.3)
2. Open the control box. (Refer to section 2.3.3)
3. Remove the 2 screws which fasten the thermostat.
4. Disconnect 2 leads of thermostat terminals.
5. Remove the thermostat.
6. Re-install the components by refereing to the  above

removal procedure. (See Figure 11)

1. Remove the control box. (Refer to section 2.1.3)
2. Open the control box. (Refer to section 2.3.3)
3. Remove the 2 screws which fasten the rotary switch.
4. Disconnect all the leads of the rotary switch terminals.
5. Remove the rotary switch.
6. Re-install the components by referring to the  above

removal procedure. (See Figure 12)