DOWNLOAD JBL SPYRO (serv.man3) Service Manual ↓ Size: 7.74 MB | Pages: 72 in PDF or view online for FREE

 

Page 15 of 62 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IECEN 60065F 

                                                             TRF originator BEAB 

 

 

Coil formers and partition walls > 0,4 mm 

 

N 

14.3.4.2 

Class I transformers, with basic insulation and 
protective screening only if all 7 conditions of 
14.3.4.2 are met 

 N 

14.3.4.3 

Separating transformers with at least basic 
insulation 

 N 

14.3.5.1 

Class II transformers have adequate insulation 
between hazardous live parts and accessible parts 
(double or reinforced insulation) 

 N 

 

Coil formers and partition walls > 0,4 mm 

 

N 

14.3.5.2 

Class I transformers have adequate insulation 
between hazardous live parts and accessible 
conductive parts or those conductive parts or 
protective screens connected to a protective earth 
terminal 

 N 

 

Winding wires connected to protective earth have 
adequate current-carrying capacity 

 N 

14.4 

High voltage components 

No component operating at 
voltages exceeding 4 kV. 

N 

 

High-voltage components and assemblies: 
U > 4 kV (peak) separately approved 

 N 

 

Component meets category V-1 of IEC 60707 

 

N 

14.4.1 

High voltage transformers and multipliers tested as 
part of the submission 

 N 

14.4.2 

High voltage assemblies and other parts tested as 
part of the submission 

 N 

14.5 Protective 

devices 

 

N 

 

Protective devices used within their ratings 

 

N 

 

External clearances and creepage distances meet 
requirement of clause 13 for the voltage across the 
device when opened 

 N 

14.5.1.1 

a) Thermal cut-outs separately approved 

No thermal cut-outs provided. 

N 

 

b) Thermal cut-outs tested as part of the 
submission 

 N 

14.5.1.2 

a) Thermal links separately approved 

No thermal links provided. 

N 

 

b) Thermal links tested as part of the submission 

 

N 

14.5.1.3 

Thermal devices re-settable by soldering 

No such components provided. 

N 

14.5.2.1 

Fuse-links in the mains circuit according to IEC 
60127 

No such components provided. 

N 

14.5.2.2 

Correct marking of fuse-links adjacent to holder ... :  

N 

 

Page 16 of 62 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IECEN 60065F 

                                                             TRF originator BEAB 

 

14.5.2.3 

Not possible to connect fuses in parallel ............... :  

N 

14.5.2.4 

Not possible to touch hazardous live parts when 
replacing fuse-links without the use of a tool ......... :

 N 

14.5.3 

PTC-S thermistors comply with IEC 60730-1 

No such components provided. 

N 

 

PTC-S devices (15 W) category V-1 or better 

 

N 

14.5.4 Circuit 

protectors 

have adequate breaking capacity 

and their position is correctly marked 

No such components provided. 

N 

14.6 Switches 

No 

switches controls > 0,2A , 

35 Vpeak a.c. or 24 Vdc 

N 

14.6.1 a) 

Separate testing to IEC 61058 including: 

10 000 operations 

Normal pollution suitability 

Resistance to heat and fire level 3 

and 

V-0 compliance with annex G, G.1.1 

 N 

14.6.1 b) 

Tested in the apparatus: 

 

N 

 

Switch controlling > 0.2A with open contact  
voltage > 35 V (peak)/24 V dc complying with 
14.6.3, 14.6.4 and V-0 in annex G, G.1.1 

 N 

 

Switch controlling > 0.2A with open contact  
voltage < 35 V (peak)/24 V dc complying with 
14.6.3 and V-0 in annex G, G.1.1 

 N 

 

Switch controlling < 0.2A with open contact  
voltage > 35 V (peak)/24 V dc complying with  
14.6.4 and V-0 in annex G, G.1.1 

 N 

14.6.2 

Switch tested to 14.6.1 b) constructed to IEC 
61058-1 subclause 13.1 and has making/breaking  
action independent of speed of actuation 

 N 

14.6.3 

Switch tested to 14.6.1 b) compliant with IEC 
61058-1 subclause 16.2.2 d) and  m) not attaining 
excessive temperatures in use 

 N 

14.6.4 

Switch tested to 14.6.1 b) has adequate dielectric 
strength 

 N 

14.6.5 

Mains switch controlling mains socket outlets 
additional tests to IEC 60058-1 

 N 

 

Socket outlet current marking correct 

 

N 

14.7 

Safety interlocks 

No safety interlocks provided. 

N 

 

Safety interlocks to 2.8 of IEC 60950 

 

N 

14.8 

Voltage setting devices 

No voltage setting device 

N 

 

Page 17 of 62 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IECEN 60065F 

                                                             TRF originator BEAB 

 

 

Voltage setting device not likely to be changed 
accidentally 

 N 

14.9 

Motors 

No motors provided. 

N 

14.9.1 

Endurance test on motors 

 

N 

 

Motor start test 

 

N 

 

Dielectric strength test 

 

N 

14.9.2 

Not adversely affected by oil or grease etc. 

 

N 

14.9.3 

Protection against moving parts 

 

N 

14.9.4 

Motors with phase-shifting capacitors, three-phase 
motors and series motors meet clause. B.8, B.9 
and B.10 of IEC 60950, Annex B 

 N 

14.10 Batteries 

None 

N 

14.10.1 

Batteries mounted with no risk of accumulation of 
flammable gases 

 N 

14.10.2 

No possibility of recharging non-rechargeable 
batteries 

 N 

14.10.3 

Recharging currents and times within 
manufacturers limits 

 N 

 

Lithium batteries discharge and reverse currents 
within the manufacturers limits 

 N 

14.10.4 

Battery mould stress relief 

No special battery 

N 

14.10.5 

Battery drop test 

 

N 

14.11 

Optocouplers 

No such components 

N 

 

Optocouplers comply with Cl. 8 

 

N 

 

 N 

14.12 

Surge suppression varistors 

No such components 

N 

 

Comply with IEC 61051-2 

 

N 

 

Not connected between mains and accessible 
parts except for earthed parts of permanently 
connected apparatus 

 N 

 

Complies with the current pulse, fire hazard and 
thermal stress requirements of 14.12 

 N 

 

 

Page 18 of 62 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IECEN 60065F 

                                                             TRF originator BEAB 

 

 
 

15 TERMINALS 

P 

15.1.1 

Mains plug, appliance inlet, interconnection 
couplers and mains socket-outlet meet the 
appropriate standard 

Powered 18 Vd.c. by certified 
adaptor 

N 

15.1.2 

Connectors for antenna, earth, audio, video or data: 

P 

 

No risk of insertion in mains socket-outlets 

No risk of insertion in mains 
socket-outlets 

P 

 

No risk of insertion into audio or video: outlets 
marked with the symbol of 5.2 

None N 

15.1.3 

Output terminals of a.c. adaptors or similar devices 
not compatible with household mains socket-
outlets 

- No output terminals od supply 
apparatus. 
- Powered 18 Vd.c. by certified 
adaptor 

N 

15.2 

Provision for protective earthing 

N 

 

Accessible conductive parts of Class I equipment 
reliably connected to earth terminal, within 
equipment 

No protective earthing 

N 

 

Class I supply equipment with non-hazardous live 
output voltage: output circuit not connected to 
earth 

 N 

 

Protective earth conductors correctly coloured 

 

N 

 

Equipment with non-detachable mains cord 
provided with separate protective earth terminal 
near mains input 

 N 

 

Protective earth terminal resistant to corrosion 

 

N 

 

Earth resistance  test: < 0,1 

Ω at 25 A ................... :  N 

15.3 

Terminals for external flexible cords and for 
permanent connection to the mains supply 

Powered 18 Vd.c. by certified 
adaptor 

N 

15.3.1 

Adequate terminals for connection of permanent 
wiring 

 N 

15.3.2 

Reliable connection of non-detachable cords: 

 

N 

 

Not soldered to conductors of a printed circuit 
board 

 N 

 

Adequate clearances and creepage distances 
between connections should a wire break away 

 N 

 

Wire secured by additional means to the conductor  

N 

15.3.3 

Screws and nuts clamping conductors have 
adequate threads: ISO 261, ISO 262 or similar 

 N