JBL ON STAGE 200ID EMC - CB Certificate ▷ View online
- Page 56 of 63 -
Report
No.
98323
IEC 60950-1:2005 / EN 60950-1:2006
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IECEN60950_1C
2.5
TABLE: limited power sources
N
Circuit output tested: See below
Measured Uoc (V) with all load circuits
disconnected: See below
disconnected: See below
I
sc
(A)
VA
Measuring position
Meas.
Limit
Meas.
Limit
supplementary information:
2.10.2
TABLE: determination of operating voltage measurement
⎯
Location
Component
From
To
Peak Voltage (Vac) RMS Voltage (Vac) Comments
supplementary information:
2.10.3 and
2.10.4
2.10.4
TABLE: Clearance and creepage distance measurements
N
Clearance (cl) and creepage
distance (cr) at/of/between:
distance (cr) at/of/between:
U peak
(V)
U r.m.s.
(V)
Required cl
(mm)
cl
(mm)
Required cr
(mm)
cr
(mm)
supplementary information:
- Page 57 of 63 -
Report
No.
98323
IEC 60950-1:2005 / EN 60950-1:2006
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IECEN60950_1C
Copy of PCB, layout of tracing (not to scale):
2.10.5
TABLE: Distance through insulation measurements
N
Distance through insulation (DTI) at/of:
U peak
(V)
U rms
(V)
Test
voltage
(Vac)
Required DTI
(mm)
DTI
(mm)
supplementary information:
- Page 58 of 63 -
Report
No.
98323
IEC 60950-1:2005 / EN 60950-1:2006
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IECEN60950_1C
4.3.8 TABLE:
Batteries
N
The tests of 4.3.8 are applicable only when appropriate battery
data is not available
data is not available
Is it possible to install the battery in a reverse polarity position?
Non-rechargeable batteries
Rechargeable batteries
Discharging
Charging
Discharging
Reversed
charging
Meas.
current
Manuf.
Specs.
Specs.
Un-
intentional
charging
Meas.
current
Manuf.
Specs.
Specs.
Meas.
current
Manuf.
Specs.
Specs.
Meas.
current
Manuf.
Specs.
Specs.
Max.
current
during
normal
condition
current
during
normal
condition
Max.
current
during
fault
condition
current
during
fault
condition
Test results:
Verdict
- Chemical leaks
- Explosion of the battery
- Emission of flame or expulsion of molten metal
- Electric strength tests of equipment after completion of tests
supplementary information:
- Page 59 of 63 -
Report
No.
98323
IEC 60950-1:2005 / EN 60950-1:2006
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IECEN60950_1C
4.5
TABLE: Thermal requirements
P
Supply voltage (V) .....................
90V / 50Hz
264V / 60Hz
⎯
Maximum measured temperature T of
part/at::
part/at::
T (
°C)
Allowed
T
max
(
°C)
Supplied 1KHz sine wave for speakers in computer speaker system and obtain 1/8 Maximum non-clipped
output power, & charging Ipod (500mA 5V)
output power, & charging Ipod (500mA 5V)
Adaptor enclosure
45.1
48.5
80.3
Plug part of adaptor enclosure
32.5
32.7
80.3
PCB under IC U5
79.4
86.2
90.3
L2 81.4
88.7
115.3
PCB near Q5
70.5
74.6
90.3
C13 69.6
74.9
90.3
External enclosure of speaker
57.6
62.1
80.3
External enclosure near Ipod socket
40
40.8
80.3
External enclosure near on/off switch
41.3
43.5
80.3
Ambient 25.5
25.3
--
Having a specified maximum ambient temperature of 40°C, the maximum temperatures are calculated
based upon a (minimum) test temperature of 25.3°C. Temp. limits are adjusted according to Cl. 1.4.12.3.
Temperature limits include less 10K for thermocouple measurement method.
based upon a (minimum) test temperature of 25.3°C. Temp. limits are adjusted according to Cl. 1.4.12.3.
Temperature limits include less 10K for thermocouple measurement method.
Temperature T of winding:
t
1
(°C)
R
1
(
Ω)
t
2
(°C)
R
2
(
Ω)
T (
°C)
Allowed
T
max
(
°C)
Insulatio
n class
supplementary information:
Click on the first or last page to see other ON STAGE 200ID service manuals if exist.