DOWNLOAD JBL CINEMA SOUND 3 (serv.man2) Service Manual ↓ Size: 1.98 MB | Pages: 95 in PDF or view online for FREE

 
 

Report No. JSH006110139-001 

Page 64 of 94  

 
16.1 Severity Level and Performance Criterion 

16.1.1 Test level 

 

Level 

Test field strength V/m 

 

1 

 

1 

2 

 

3 

3 

 

10 

 

X 

Special 

 
Note: 1. X is an open test level, this level may be given in the product specification. 
          2. The gray row is the selected test level. 

 

16.1.2 Performance Criterion   

 

   Performance 

criterion 

 

 
 

Report No. JSH006110139-001 

Page 65 of 94  

16.2 Block diagram of test setup 
 

 
 
16.3 Test Setup and Test Procedure 
 

16.3.1 Test setup 

 

 

The test was conducted in an anechoic chamber which is 7m in length, 5m in width and 3m in 

height   to  maintain a uniform field of sufficient dimensions with respect to the EUT, and also in 
order to  comply with various national and international laws prohibiting interference to radio 
communications. 

  

 

 

For the table top EUT, the equipment is placed in the test facility on a non-conducting table 

0.8m high. 
 

For the floor standing EUT, the equipment is placed in the test facility on a non-conducting 

support 0.1m high. 
 

The EUT was placed on the uniform calibrated plane which is 3V/m EM field. 

 
 

Unshielded parallel wire was used during the test. 

 

 

 

Wire is left exposed to the electromagnetic field for a distance of 1m form the EUT. 

Power 

Antenn
a mask

   
       Table 

amplifier 

Signal 

EUT 

Field probe 

Field 

Optical 

Filte

 
 

Report No. JSH006110139-001 

Page 66 of 94  

16.3.2 Test procedure 

 
 

The EUT was arranged and connected according to its functional requirements 

 

Before testing, the intensity of the established field strength have been checked by placing the 

field sensor at a calibration grid point, and with the field generating antenna and cables in the same 
positions as used for the calibration, the forward power needed to give the calibrated field strength was 
measured. 
 

Spot checks was made at a number of calibration grid points over the frequency range 80MHz 

to 1000MHz, both polarizations was checked. 
 

After calibration, the EUT is initially placed with one face coincident with the calibration 

plane. 
 

The frequency range is swept from 80MHz to 1000MHz, with the signal 80% amplitude 

modulated  

with a 1 kHz sinewave, pausing to adjust the r.f. signal level.  

 
 

The dwell time at each frequency was 3s so as that the EUT to be exercised and be able to 

respond. 
 

The step size was 1% of the fundamental with linear interpolation between calibrated points. 

 

Test was performed with the generating antenna facing each of the four sides of the EUT. 

 

Both horizontal and vertical polarization was conducted. 

16.3.3 Photo for test set-up 

           none 

 
16.4 Test Protocol 
 

 Temperature 

 

 :23

°C  

 Relative 

Humidity :34% 

 

Test no.: 

 
 

Frequency 

(MHz) 

Polarization Test 

level 

V/m 

Exposed 
location 

Result Comment 

1 
 

80-1000 

H & V 

3 

Front side 

Pass 

 

2 
 

80-1000 

H & V 

3 

Back side 

Pass 

 

3 900 

H&V 

3 Front/Back 

Pass 

 

 
 

 

  

 
 None

 

 

 
 

Report No. JSH006110139-001 

Page 67 of 94  

 

 
17.1 Severity Level and Performance Criterion 
 

17.1.1 Test level 

Level 

Open-sircuit test voltage +/-10% 

kV 

1 0.5 

2 

1.0 

3 

2.0 

4 4.0 

  X* 

Special 

 

Notes: 1.”X” is an open class. This level can be specified in the product  Specification 
            2. The gray rows are the selected level. Class 2 is applied to Phase to Phase (L-N) 
               Class 3 is applied to Phase to PE (L-PE),(N-PE)

 

 

17.1.2 Performance Criterion

 

 

 

Performance criterion B.