JBL AUTHENTICS L8 (serv.man2) EMC - CB Certificate ▷ View online
Report No.: EM201300650-1 Application No.: ZJ00032008 Page 33 of 42
4.5 RECEIVER SPURIOUS EMISSIONS
4.6.1 LIMITS
Frequency range
Limit
30 MHz to 1 GHz
-57 dBm
above 1 GHz to 12,75 GHz
-47 dBm
4.6.2 TEST METHOD
EUT operation status:
Keep EUT on continuously receiving status by the software
provided by manufacturer.
provided by manufacturer.
Test channel:
802.11b/g
Mid channel: (2442MHz)
Mid channel: (2442MHz)
Test condition:
Normal test conditions.
Test equipment used:
Refer to section 3.4
Test procedure:
1. The EUT shall be performed at the receiver mode and
Interface cables, loads, and devices should be connected to
at least one of each type of the interface ports of the EUT
and, where practical, each cable shall be terminated in a
device typical for its actual use. EUT shall be placed at the
1.5m support on the turntable.
at least one of each type of the interface ports of the EUT
and, where practical, each cable shall be terminated in a
device typical for its actual use. EUT shall be placed at the
1.5m support on the turntable.
2. The test antenna at a horizontal distance of 3 m .It shall be
raised and lowered from 1m to 4m until a maximum signal
level is detected by the measuring receiver. Then the
turntable should be rotated through 360° in the horizontal
plane, until the maximum signal level is detected by the
measuring receiver. In both the vertical and the horizontal
polarization. Record the reading level, antenna position,
polarization and turntable position.
level is detected by the measuring receiver. Then the
turntable should be rotated through 360° in the horizontal
plane, until the maximum signal level is detected by the
measuring receiver. In both the vertical and the horizontal
polarization. Record the reading level, antenna position,
polarization and turntable position.
3. Remove the EUT and replace it with a substitution antenna
(the antenna should be half-wavelength for each frequency
involved). The center of the substitution antenna should be
approximately at the same location as the center of the
transmitter. For frequencies of 80 MHz and above, the
dipoles should have their arm lengths set for resonance at
the frequency of test. Below 80 MHz, shortened arm lengths
are recommended. For measurements above 1 000 MHz, a
waveguide horn is recommended. The centre of this antenna
should coincide with either the phase centre or volume
centre.
involved). The center of the substitution antenna should be
approximately at the same location as the center of the
transmitter. For frequencies of 80 MHz and above, the
dipoles should have their arm lengths set for resonance at
the frequency of test. Below 80 MHz, shortened arm lengths
are recommended. For measurements above 1 000 MHz, a
waveguide horn is recommended. The centre of this antenna
should coincide with either the phase centre or volume
centre.
4. Feed the substitution antenna at the EUT end with a signal
Report No.: EM201300650-1 Application No.: ZJ00032008 Page 34 of 42
generator connected to the antenna by a cable. With the
antennas at both ends vertically polarized, and with the
signal generator tuned to a particular test frequency, raise
and lower the test antenna to obtain a maximum reading at
the spectrum analyzer. Adjust the level of the signal
generator output until the previously recorded maximum
reading for this set of conditions is obtained. This should be
done carefully repeating the adjustment of the test antenna
and generator output.
antennas at both ends vertically polarized, and with the
signal generator tuned to a particular test frequency, raise
and lower the test antenna to obtain a maximum reading at
the spectrum analyzer. Adjust the level of the signal
generator output until the previously recorded maximum
reading for this set of conditions is obtained. This should be
done carefully repeating the adjustment of the test antenna
and generator output.
5. Where: E.I.R.P (dBm) = Pg (dBm) – cable loss (dB) +
antenna gain (dBi). Pg is the generator output power into the
substitution antenna
substitution antenna
Remark:
/
Report No.: EM201300650-1 Application No.: ZJ00032008 Page 35 of 42
4.6.3 TEST SETUP
Below 1GHz
Above 1GHz
Above 1GHz
EUT
Ground Plane
3 m
1.5
m
m
Cable
Test table & Turntable
1m
EMI
Receiver
EUT
Ground Plane
3 m
1.5 m
Cable
Test table & Turntable
1m ~ 4m
EMI
Receiver
Report No.: EM201300650-1 Application No.: ZJ00032008 Page 36 of 42
4.6.4 TEST RESULTS
802.11b mode:
Mid channel (2442MHz)
Below 1GHz:
No.
Mid channel (2442MHz)
Below 1GHz:
No.
Frequency
Reading
Correct
Result
Limit
Margin
Remark
(MHz)
(dBm)
Factor(dB)
(dBm)
(dBm)
(dB)
1
122.9389 -77.88 8.80 -69.08 -57.00 -12.08
Vertical
2
129.3165 -83.25 8.69 -74.56 -57.00 -17.56
Vertical
3
160.1008 -82.44 10.69 -71.75 -57.00 -14.75
Vertical
4
269.9983 -87.38 14.15 -73.23 -57.00 -16.23
Vertical
5
317.7868 -91.85 16.09 -75.76 -57.00 -18.76
Vertical
6
418.5244 -94.59 18.32 -76.27 -57.00 -19.27
Vertical
7
110.4892 -85.34 9.46 -75.88 -57.00 -18.88
Horizontal
8
122.9389 -77.40 8.80 -68.60 -57.00 -11.60
Horizontal
9
143.8877 -84.01 9.55 -74.46 -57.00 -17.46
Horizontal
10
160.1008 -78.43 10.69 -67.74 -57.00 -10.74
Horizontal
11
269.9983 -86.25 14.15 -72.10 -57.00 -15.10
Horizontal
12
418.5244 -92.09 18.32 -73.77 -57.00 -16.77
Horizontal
Above 1GHz:
No.
Frequency
Reading
Correct
Result
Limit
Margin
Remark
(MHz)
(dBm)
Factor(dB)
(dBm)
(dBm)
(dB)
1
2713.552 -93.57 29.75 -63.82 -47 -16.82
Vertical
2
2911.54 -93.28 32.58 -60.7 -47 -13.7
Vertical
3
2989.455 -94.48 33.66 -60.82 -47 -13.82
Vertical
4
3063.265 -76.94 11.69 -65.25 -47 -18.25
Vertical
5
9971.595 -89.61 25.65 -63.96 -47 -16.96
Vertical
6
12144.02 -87.06 25.59 -61.47 -47 -14.47
Vertical
7
2694.509 -90.17 29.47 -60.7 -47 -13.7
Horizontal
8
2810.803 -90.87 31.18 -59.69 -47 -12.69
Horizontal
9
2989.455 -92.04 33.66 -58.38 -47 -11.38
Horizontal
10
3056.17 -77.71 11.68 -66.03 -47 -19.03
Horizontal
11
9902.47 -88.23 25.53 -62.7 -47 -15.7
Horizontal
12
12573.842 -87.08 26.67 -60.41 -47 -13.41
Horizontal
Click on the first or last page to see other AUTHENTICS L8 (serv.man2) service manuals if exist.