Harman Kardon DRIVE AND PLAY (serv.man16) User Manual / Operation Manual ▷ View online
Direct Connection of the 12-Volt Power Harness With
In-Line Fuse Holder
In-Line Fuse Holder
Use this method when you want a permanent power connec-
tion to the vehicle. Also, by connecting the harness’s red wire
to the ignition switch’s ACC terminal, Drive + Play will turn on
tion to the vehicle. Also, by connecting the harness’s red wire
to the ignition switch’s ACC terminal, Drive + Play will turn on
or off with the vehicle’s ignition (ACC) switch. An in-line fuse
holder provides protection for the unit.
holder provides protection for the unit.
IMPORTANT: Replace the in-line fuse only with one of the
same type and rating.
same type and rating.
INSTALLATION 5
INSTALLATION
ENGLISH
Auxiliary
Device
(optional)
Third-Party
CD Changer
Interface
(optional)
Text Display
Back
Side
+12Vdc = yellow
CD Changer L/R In
Aux. L/R In
Antenna In
2A Fuse
ACC = red
GND = black
Electronics Enclosure
Antenna Cable
(disconnect from
Head Unit/Radio)
(disconnect from
Head Unit/Radio)
Head Unit/Radio
or
or
or
Cell Phone,
Satellite Radio, etc.
iPod Cable
3.5mm Stereo Cable
(not included)
Line Out Cable
Wired
FM Adaptor
12-Volt
Power
Harness
12-Volt
Accessory
Power Cable
Accessory
Power Cable
iPod
Control Knob
Tip = LEFT
Sleeve = GROUND
3.5mm Stereo
Mini-Plug Cable
RIGHT = Ring
Audio Input/Output Jacks
Wiring Diagram
Installing Components
Installing the Electronics Enclosure
At the selected site, install the Electronics Enclosure. Use either
the enclosed cable ties or mounting screws, as shown below.
the enclosed cable ties or mounting screws, as shown below.
Installing the Text Display
1. Temporarily place the Text Display at the proposed site
and check the default viewing angle while adjusting the
pivot arm. If it meets your needs, then skip to step 2.
Otherwise, change the viewing angle as follows:
pivot arm. If it meets your needs, then skip to step 2.
Otherwise, change the viewing angle as follows:
a. Using the 3 mm hex key, loosen the recessed hex screw
(inside the display base) until the pivot arm is free from
the display assembly. The hex screw will remain captive.
the display assembly. The hex screw will remain captive.
b. Select another viewing angle position (middle or top).
Reassemble the parts in reverse order and tighten the
recessed hex screw.
recessed hex screw.
2. At the base, using the 1.5mm hex key, loosen (but do not
remove) the hex setscrew.
3. To install the Text Display with adhesive tape, perform the
following steps or skip to step 4:
a. Insert the mounting plate, rotate it 180°, and tighten
the hex setscrew as shown below.
6 INSTALLATION
Recessed
Hex Screw
Hex Screw
Display
Assembly
Assembly
Display
Base
Base
3mm
Hex Key
Mounting
Plate
Plate
Adhesive
Pad
Pad
Hex Setscrew
b. At the proposed site, wipe the surface and exposed
mounting plate with one of the enclosed alcohol pads.
Allow both to dry.
Allow both to dry.
c. Remove the protective tape from one side of one of the
enclosed adhesive pads, and press the pad against the
mounting plate.
mounting plate.
d. Remove the remaining protective tape, and press and
hold the Text Display to its site for 5 seconds.
4. To install the Text Display with mounting screws, perform
the following steps:
a. At the proposed site, place the mounting plate and
rotate it so that the arrow will point toward the hex
set-screw at the back of the base after it’s mounted.
set-screw at the back of the base after it’s mounted.
b. Holding the mounting plate in position, fasten it to the
surface with three enclosed mounting screws.
c. Place the Text Display on the mounting plate (180°
from its final position), and then rotate it a half-turn to
the final position. Tighten the hex setscrew at the back
of the base.
the final position. Tighten the hex setscrew at the back
of the base.
5. Route the attached cable to the Electronics Enclosure.
Installing the Control Knob
NOTE: The Control Knob’s cable can be routed differently
for adhesive or screw mounting. The default cable route is
through the back of the base and should be used when
mounting the base with the supplied adhesive pad. For screw
mounting, the cable can be routed through the center of the
base and through a hole that must be drilled in the mounting
surface. You may use the mounting plate as a template.
for adhesive or screw mounting. The default cable route is
through the back of the base and should be used when
mounting the base with the supplied adhesive pad. For screw
mounting, the cable can be routed through the center of the
base and through a hole that must be drilled in the mounting
surface. You may use the mounting plate as a template.
1. Place the Control Knob at the site and check the operation
angle with the default 30° base. If it meets your needs,
then skip to step 2. Otherwise, change the base as follows:
then skip to step 2. Otherwise, change the base as follows:
a. Using a Phillips screwdriver, remove the two screws
from the bottom of the base and set the internal
mounting plate aside.
mounting plate aside.
b. While holding the base, grasp the Control Knob and turn
it to the right until you feel it release from the base.
Slide the base off the attached cable and put it aside.
Slide the base off the attached cable and put it aside.
c. Select another base (0° or 60°) and thread the cable
through the base to meet the Control Knob.
d. Place the new base against the Control Knob bottom and
turn it to the left until it locks. Route the attached cable
through the base’s opening. Fasten the internal mounting
plate to the base with the screw(s) from step a.
through the base’s opening. Fasten the internal mounting
plate to the base with the screw(s) from step a.
NOTE: The 60° base uses two screws, while the 0° base
uses one screw.
uses one screw.
INSTALLATION 7
INSTALLATION
ENGLISH
Mounting
Plate
Hex Setscrew
Arrow
Control
Knob
Knob
30° Base
Internal
Mounting
Plate
Mounting
Plate
Control
Knob
0° Base
Cable Through
0° Base and Internal
Mounting Plate
Internal
Mounting
Plate
Mounting
Plate
Installing Components
Installing the Control Knob (continued)
2. At the base (below the cable), using the 1.5mm hex key,
loosen (but do not remove) the hex setscrew.
3. To install the Control Knob with adhesive tape, perform the
following steps or skip to step 4:
a. Insert the mounting plate, rotate it 180°, and tighten
the hex setscrew.
b. At the site, wipe the surface and exposed mounting
plate with one of the enclosed alcohol pads. Allow both
to dry.
to dry.
c. Remove the protective tape from one side of one of the
enclosed adhesive pads, and press the pad against the
mounting plate.
mounting plate.
d. Remove the remaining protective tape, and press and
hold the Control Knob to its site for 5 seconds.
4. To install the Control Knob with mounting screws, perform
the following steps:
a. At the proposed site, place the mounting plate and
rotate it so that the arrow will point toward the hex
set-screw at the back of the base after it’s mounted.
set-screw at the back of the base after it’s mounted.
b. Holding the mounting plate in position, fasten it to the
surface with three enclosed mounting screws.
c. Using the mounting plate’s center hole as a template,
drill a hole through the mounting surface and pass the
Control Knob’s cable through the hole.
Control Knob’s cable through the hole.
d. Place the Control Knob on the mounting plate (180°
from its final position), and then rotate it a half-turn to
the final position. Tighten the hex setscrew at the back
of the base.
the final position. Tighten the hex setscrew at the back
of the base.
5. Route the attached cable to the Electronics Enclosure.
Installing the iPod Cable
Route the iPod dock connector cable to the chosen iPod site
(e.g., the center console compartment or the glove box). Be
sure to leave enough cable exposed to make connecting and
disconnecting the iPod easy.
(e.g., the center console compartment or the glove box). Be
sure to leave enough cable exposed to make connecting and
disconnecting the iPod easy.
Making the System Connections
With all power off, refer to the Wiring Diagram on page 5 and
make only the power, ground and audio signal connections
that apply to the scheme you have chosen. After verifying all
connections including the iPod, proceed to the next section,
Operating Drive + Play.
make only the power, ground and audio signal connections
that apply to the scheme you have chosen. After verifying all
connections including the iPod, proceed to the next section,
Operating Drive + Play.
OPERATING DRIVE + PLAY
Distraction Warning
Do not connect or disconnect your iPod or program Drive +
Play while driving. Always pull off the road and park in a
position that you are absolutely sure presents no risk before
browsing your iPod or adjusting the settings on your Drive +
Play. Always obey all traffic laws while driving.
Play while driving. Always pull off the road and park in a
position that you are absolutely sure presents no risk before
browsing your iPod or adjusting the settings on your Drive +
Play. Always obey all traffic laws while driving.
Overview
8 INSTALLATION/OPERATION
Mounting
Plate
Plate
Control Knob
With 0° Base
With 0° Base
Adhesive
Pad
Pad
Mounting
Plate
Plate
Control Knob
With 0° Base
Arrow
Next/Fast Forward
Press Once to Play Next Track
Select
Press Once to Choose
Highlighted Menu Item
Highlighted Menu Item
Scroll Ring
Scroll Right Once to Next Menu Item
Scroll Right and Hold to Jump Forward
In Now Playing, Scroll Right to
Fast Forward
Scroll Right and Hold to Jump Forward
In Now Playing, Scroll Right to
Fast Forward
Scroll Ring
S
croll Left Once to Last Menu Item
Scroll Left and Hold to Jump Back
In Now Playing, Scroll Left to
Fast Rewind
Menu
Press Once to
Jump to Last Screen
Play/Pause
Press Once to Stop or
Resume Play of Current Track
Previous/Rewind
Press Once to Play Last Track
Click on the first or last page to see other DRIVE AND PLAY (serv.man16) service manuals if exist.