Harman Kardon SB 30 (serv.man2) EMC - CB Certificate ▷ View online
Report No:W-N-1109009-CY-01-1
Telecom Technology Center
de:
Aud
Test Mo
io In (1KHz)
Discharge Mode
Contact Discharge
ir Discharge
A
ESD Voltage
2 kV
4 kV
2 kV
4 kV
8 kV
Points\R
rity + - + - + - + - + -
esult\Pola
Points
A A
B A A A A
B
B
B
VCP A
A
B
B
HCP A
A
B
B
N/A
Test Mode:
Digital In (1KHz)
Discharge Mode
Contact Discharge
Air Discharge
ESD Voltage
2 kV
4 kV
2 kV
4 kV
8 kV
Points\Result\Polarity + - + - + - + - + -
Points
A A B B A A A A B B
VCP A
A
B
B
HCP A
A
B
B
N/A
45
Report No:W-N-1109009-CY-01-1
Telecom Technology Center
Te Mode:
st
Audio In (100Hz)
Discharge M
t Discharge
Air Discharge
ode
Contac
ESD Voltage
2 kV
4 kV
2 kV
4 kV
8 kV
Poin
ity + - + - + - + - + -
ts\Result\Polar
Points
A A B B A A A A B B
VCP A
A
B
B
HCP A
A
B
B
N/A
Te Mode:
st
Audio In (100Hz)
Discharge M
Discharge
Air Discharge
ode
Contact
ESD Voltage
2 kV
4 kV
2 kV
4 kV
8 kV
Poin
ity + - + - + - + - + -
ts\Result\Polar
Points
A A B B A A A A B B
VCP A
A
B
B
HCP A
A
B
B
N/A
46
Report No:W-N-1109009-CY-01-1
Telecom Technology Center
6.8 EFT/BURST TESTING
6
ficatio
Ba
IEC 61000-4-4
.8.1 Test Speci
n
sic Standard:
Test Voltage:
Power
ne:1
, C xial
ble:
kV
Li
kV
oa
Ca
0.5
Impul
e shape :
0 n
se Wav
5/5
s
Burst Duration:
ms
15
Burst Period:
300 ms
Test Duration:
t le
han 1 min.
No
ss t
6.8.2 Test Procedure
he EUT and support equipment, are placed on a table that is 0.8 meter above a metal
ne
in. and 0.65mm thick min.
The other condition as following manner:
a
a
wer cor
ing device and t
not
er.
b. Both positive and negative polarity discharges were applied.
f e
test sequential was 1 m
te
d. For the actual test configuration, please refer to the related Item
6.8.3
tion From
es
tan
rd
No deviation
T
ground pla
measured 1m*1m m
. The length of po
d between the coupl
he EUT should
exceed 1 met
c. The duration time o ach
inu
–EUT Test Photos.
Devia
T t S
da
47
Report No:W-N-1109009-CY-01-1
Telecom Technology Center
6.8.4 Test Setup
Note:
TABLE-TOP EQUIPMENT
The configuration consisted of a wooden table (0.8m high) standing on the Ground
eference Plane. The GRP consisted of a sheet of aluminum (at least 0.25mm thick
R
and 2.5m square) connected to the protective
and 2.5m square) connected to the protective
f 0.5m was provided between the EUT and
grounding system. A minimum distance
the walls of the laboratory or any other
ure.
Note: (1) P/N denotes the Positive/Negative polarity of the output voltage.
(2) N/A - denotes test is not applicable in this test report
(3) Criteria A: There was no change operated with initial operating during the
(3) Criteria A: There was no change operated with initial operating during the
test.
(4) Criteria B: The EUT function loss during the test, but self-recoverable after
the test.
(5) Criteria C: The system shut down during the test.
(6) The test was performed in EFT Room.
(6) The test was performed in EFT Room.
o
metallic struct
metallic struct
48
Click on the first or last page to see other SB 30 (serv.man2) service manuals if exist.