Harman Kardon HS 500 (serv.man2) EMC - CB Certificate ▷ View online
Report No. JSH006030498-001
Page 60 of 82
15.2 Block Diagram of Test Setup
15.2 .1Test Set
Ta
plane
The distance between the EUT and any other of the metallic surface except the GRP is
greater than 0.5m.
The main lead excess than 1m is gathered into a flat coil with a 0.4m diameter and situated
at a distance of 0.1m above the ground reference plane to insure the distance between the
coupling device and the EUT were 1m or less.
The EUT was arranged and connected to satisfy its functional requirement and supplied by
The coupling-decoupling network (Best EMC).
The distance between the EUT and any other of the metallic surface except the GRP is
greater than 0.5m.
The main lead excess than 1m is gathered into a flat coil with a 0.4m diameter and situated
at a distance of 0.1m above the ground reference plane to insure the distance between the
coupling device and the EUT were 1m or less.
The EUT was arranged and connected to satisfy its functional requirement and supplied by
The coupling-decoupling network (Best EMC).
Floor Standing EUT
The EUT was placed on a 0.1m high wooden support, standing on the ground reference
plane 2.6m by 1.8m, made by aluminium 0.5mm thick.
The distance between the EUT and any other of the metallic surface except the GRP is
greater than 0.5m.
The main lead excess than 1m is gathered into a flat coil with a 0.4m diameter and situated
at a distance of 0.1m above the ground reference plane to insure the distance between the
coupling device and the EUT were 1m or less.
The EUT was arranged and connected to satisfy its functional requirement and supplied by
The coupling-decoupling network (Best EMC).
plane 2.6m by 1.8m, made by aluminium 0.5mm thick.
The distance between the EUT and any other of the metallic surface except the GRP is
greater than 0.5m.
The main lead excess than 1m is gathered into a flat coil with a 0.4m diameter and situated
at a distance of 0.1m above the ground reference plane to insure the distance between the
coupling device and the EUT were 1m or less.
The EUT was arranged and connected to satisfy its functional requirement and supplied by
The coupling-decoupling network (Best EMC).
up and Test Procedure
ble top EUT
The EUT was placed on a 0.8m high wooded table, standing on the ground reference
2.6m by 1.8m in size, made by aluminium 0.5mm thick.
RP
Best EMC
EUT
G
Report No. JSH006030498-001
Page 61 of 82
15.2.2 Photo for test set-up
none
5.3 Test Protocol
Temperature :
2
Relative
3
Test No.
#
Level
[kV]
Polarity
+/-
Line for test
Pass/
Fail
Comment
1
3
°C
4%
Humidity:
1 1 +/- L P
2 1 +/- N P
3 1 +/-
PE
NA
4 1 +/-
L-N
P
5 1 +/-
L-PE
NA
6 1 +/-
N-PE
NA
7 1 +/-
L,N.PE
NA
8 0.5 +/- DC -
9 0.5 +/- I/O -
15.4 Additions, Deviations and Exclusions from Standards
None.
Report No. JSH006030498-001
Page 62 of 82
16.
eld susceptibility
Test result
Pass
6.1 Severity Level and Performance Criterion
16.1
Lev
field
th V/m
Elec
tromagnetic fi
1
.1 Test level
el
Test
s
g
tren
1
1
2
3
3
10
X
Special
Note: 1. X is an open test level, this level may be giv
the produc pecification
2. The gray row is the selected test level.
en in
t s
.
16.1.
rformance Criterion
Performance criterion A
2 Pe
Report No. JSH006030498-001
Page 63 of 82
16.2 Block diagram of test setup
16.3 Test Setup and Test Procedure
16.3.1 Test setup
The test was conducted in an anechoic chamber which is 7m in length, 5m in width and 3m in
height to maintain a uniform field of sufficient dimensions with respect to the EUT, and also in
order to comply with various national and international laws prohibiting interference to radio
communications.
order to comply with various national and international laws prohibiting interference to radio
communications.
For the table top EUT, the equipment is placed in the test facility on a non-conducting table
0.8m high.
For the floor standing EUT, the equipment is placed in the test facility on a non-conducting
support 0.1m high.
The EUT was placed on the uniform calibrated plane which is 3V/m EM field.
Unshielded parallel wire was used during the test.
Wire is left exposed to the electromagnetic field for a distance of 1m form the EUT.
Antenn
a mask
a mask
Table
am lifier
Signal
Field probe
Field
Optical
Power
p
EUT
Filte
Click on the first or last page to see other HS 500 (serv.man2) service manuals if exist.