DOWNLOAD Harman Kardon HS 350 (serv.man3) Service Manual ↓ Size: 4.39 MB | Pages: 61 in PDF or view online for FREE

 

                                                                   Page 16 of 60                        Report No. JSH007120244-002 

 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IEC/EN 60065H 

 

       TRF originator Intertek ETL SEMKO SH 

 

 

 

No risk of insertion into audio or video: outlets 
marked with the symbol of 5.2 

 

N/A 

15.1.3 

Output terminals of a.c. adaptors or similar devices 
not compatible with household mains socket-
outlets 

         

 N/A 

15.2 

Provision for protective earthing 

 

 

Accessible conductive parts of Class I equipment 
reliably connected to earth terminal, within 
equipment 

Class II 

N/A 

 

Class I supply equipment with non-hazardous live 
output voltage: output circuit not connected to 
earth 

 

N/A 

 

Protective earth conductors correctly coloured 

 

N/A 

 

Equipment with non-detachable mains cord 
provided with separate protective earth terminal 
near mains input 

 

N/A 

 

Protective earth terminal resistant to corrosion 

 

N/A 

 

Earth resistance  test: < 0,1 

Ω at 25 A ................... :  

N/A 

15.3 

Terminals for external flexible cords and for 
permanent connection to the mains supply 

 Pass 

15.3.1 

Adequate terminals for connection of permanent 
wiring 

 N/A 

15.3.2 

Reliable connection of non-detachable cords: 

 

N/A 

 

Not soldered to conductors of a printed circuit 
board 

No. Pass 

 

Adequate clearances and creepage distances 
between connections should a wire break away 

 Pass 

 

Wire secured by additional means to the conductor Mating lock connector 

Pass 

15.3.3 

Screws and nuts clamping conductors have 
adequate threads: ISO 261, ISO 262 or similar 

         

 

N/A 

15.3.4 

Soldered conductors wrapped around terminal 
prior to soldering or held in place by additional 
means 

 

N/A 

 

Clamping of conductor and insulation if not 
soldered or held by screws 

Mating lock connector, both the 
conductor and insulation are 
crimped. 

Pass 

15.3.5 

Terminals allow connection of appropriate cross-
sectional area of conductors, for the rated current 
of the equipment 

         

 

N/A 

 

                                                                   Page 17 of 60                        Report No. JSH007120244-002 

 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IEC/EN 60065H 

 

       TRF originator Intertek ETL SEMKO SH 

 

 

15.3.6 

Terminals to 15.3.3 have sizes required by 
table 16 

         

 

N/A 

15.3.7 

Terminals clamp conductors between metal and 
have adequate pressure 

 

N/A 

 

Terminals designed to avoid conductor slipping out 
when tightened or loosened 

 

N/A 

 

Terminals adequately fixed to avoid loosening 
when the clamping is tightened or loosened and 
stress on internal wiring is avoided 

 

N/A 

15.3.8 

Terminals carrying a current more than 0,2 A: 
contact pressure not transmitted by insulating 
material except ceramic 

 Pass 

15.3.9 

Termination of non-detachable cords: wires 
terminated near to each other 

 N/A 

 

Terminals located and shielded: test with 8 mm 
strand 

 

N/A 

15.4 

Devices forming a part of the mains plug 

No such device 

N/A 

15.4.1 

No undue strain on mains socket-outlets 

 

N/A 

15.4.2 

Device complies with standard for dimensions of 
mains plugs 

 

N/A 

15.4.3 

Device has adequate mechanical strength (tests 
a,b,c) 

 

N/A 

 
 

16 

EXTERNAL FLEXIBLE CORDS 

 

16.1 

Mains cords sheathed type, complying with 
IEC 60227 for PVC or IEC 60245 for synthetic 
rubber cords ............................................................ :

PVC, complying with IEC60227 

Pass 

 

Non-detachable cords for Class I have 
green/yellow core for protective earth 

 N/A 

16.2 

Mains cords conductors have adequate cross-
sectional area for rated current consumption of the 
equipment 

2 x 0.75mm

2

 Pass 

16.3 

a) Flexible cords not complying with 16.1, used for 
interconnections between separate units of 
equipment used in combination and carrying 
hazardous live voltages, have adequate dielectric 
strength 

 

N/A 

 

b) Flexible cords not complying with 16.1, 
withstand bending and mechanical stress (3.2 of 
IEC 60227-2) 

 

N/A 

 

                                                                   Page 18 of 60                        Report No. JSH007120244-002 

 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IEC/EN 60065H 

 

       TRF originator Intertek ETL SEMKO SH 

 

 

16.4 

Flexible cords used for connection between 
equipment have adequate cross-sectional areas to 
avoid temperature rise under normal and fault 
conditions 

 N/A 

16.5 

Adequate strain relief on external flexible cords 

Appliance coupler used

 

N/A

 

 

Not possible to push cord back into equipment 

 

N/A

 

 

Strain relief device unlikely to damage flexible cord

 

N/A

 

 

For mains cords of Class I equipment, hazardous 
live conductors become taut before earth 
conductor 

 N/A 

16.6 

Apertures for external flexible cord: no risk of 
damage to the cord during assembly or movement 
in use 

 Pass 

16.7 

Transportable musical instruments and amplifiers 
fitted with detachable cord set with appliance inlet 
to IEC 60320-1 

 

N/A 

 

Transportable musical instruments and amplifiers 
fitted with detachable cord sets or with means of 
stowage to protect the cord 

 

N/A 

 
 

17 ELECTRICAL 

CONNECTIONS AND MECHANICAL FIXINGS 

 

17.1 

Torque test to table 20: 

 

Pass 

 

- screws into metal: 5 times 

Cover fixed 

Pass 

 

- screws into non-metallic material: 10 times 

Cover fixed 

Pass 

17.2 

Correct introduction into female threads in non-
metallic material 

         

 

N/A 

17.3 

Cover fixing screws: captive 

         

 N/A 

 

Non-captive fixing screws: no hazard when 
replaced by a screw whose length is 10 times its 
diameter 

 Pass 

17.4 

No loosening of conductive parts carrying a current 
> 0,2 A 

 

Pass 

17.5 

Contact pressure not transmitted through plastic 
other than ceramic for connections carrying a 
current > 0,2 A 

 

Pass 

17.6 

Stranded conductors of flexible supply cords 
carrying a current > 0,2 A with screw terminals not 
consolidated by solder 

 

N/A 

 

                                                                   Page 19 of 60                        Report No. JSH007120244-002 

 

IEC/EN 60065 

Clause 

Requirement – Test 

Result - Remark 

Verdict 

 

TRF No:  IEC/EN 60065H 

 

       TRF originator Intertek ETL SEMKO SH 

 

 

17.7 

Cover fixing devices other than screws have 
adequate strength and their positioning is 
unambiguous 

No such device 

N/A 

17.8 

Fixing devices for detachable legs or stands 
provided 

No such device 

N/A 

17.9 

Internal pluggable connections, affecting safety, 
unlikely to become disconnected 

 Pass 

18 

MECHANICAL STRENGTH OF PICTURE TUBES AND PROTECTION AGAINST 
THE EFFECTS OF IMPLOSION 

 

 

Picture tube separately approved to IEC 61965: 

No picture tube 

N/A 

 

Picture tube separately approved to 18.1 ............... No 

N/A 

18.1 

Picture tubes > 16 cm intrinsically protected 

         

 

N/A 

 

Non-intrinsically protected tubes > 16 cm used with 
protective screen 

         

 

N/A 

18.2 

Intrinsically protected tubes: tests on 12 samples 

         

 

N/A 

18.2.1 

Samples subject to ageing: 6 

         

 

N/A 

18.2.2 

Samples subject to implosion test: 6 

         

 

N/A 

18.2.3 

Samples subject to mechanical strength test (steel 
ball): 6 

         

 

N/A 

18.3 

Non-intrinsically protected tubes tested to 18.3 

         

 

N/A 

 
 

19 

STABILITY AND MECHANICAL HAZARDS 

 

 

Mass of the equipment exceeding 7 kg  ................. : 4.92kg 

N/A 

 

Apparatus intended to be fastened in place – 
suitable instructions 

No 

N/A 

19.1 

Test on a plane, inclined at 10

o

 to the horizontal 

 

N/A 

19.2 

100 N force applied vertically downwards 

 

N/A 

19.3 

Apparatus mass > 25 kg or height > 1 M or 
supplied with cart or stand 

 N/A 

19.4 

Edges or corners not hazardous 

 

Pass 

19.5 

Glass surfaces with an area exceeding 0,1 m² or 
maximum dimension > 450 mm, pass the test of 
19.5.1 

No glass surface 

N/A 

19.6 

Wall or ceiling mountings adequate 

Not such function. 

N/A