Harman Kardon HK 3490 (serv.man2) EMC - CB Certificate ▷ View online
IEC 60065 7ed. (2001)
- Page 1 of 3 -
www.nemko.com
Report No. 98503
ATTACHMENT: Tables to EN/IEC 60065 7
th
edition
9.1.1.1
Touch current expressed as voltages U1 and U2 in Annex D
P
Location
Measured U1V
(peak)
(peak)
Measured U1
V (DC)
V (DC)
Measured U2
V (peak)
V (peak)
Limits :
U1 Max 35V (peak)
U1 Max 1.1V (DC)
U2 Max 0.35V (peak)
U1 Max 35V (peak)
U1 Max 1.1V (DC)
U2 Max 0.35V (peak)
Pole 1 - Antenna terminal
Pole 2 - Antenna terminal
Pole 2 - Antenna terminal
-
-
-
-
-
-
0,04Vpeak
0,03Vpeak
0,03Vpeak
Pass
Pass
Pass
Pole 1 - other part or contact
Pole 2 - other part or contact
Pole 2 - other part or contact
-
-
-
-
-
-
0,04Vpeak
0,03Vpeak
0,03Vpeak
Pass
Pass
Pass
Comments:
Vin = 253Vac, 60Hz
Only U2 have been recorded due to the use of a linear transformer in power supply.
IEC 60065 7ed. (2001)
- Page 2 of 3 -
www.nemko.com
Report No. 98503
13.3 – 13.4
Clearances and Creepage distances
P
Type of
Insulation
Position/
Location
Location
Position/
Location
Location
Operating
Voltage (V)
Clearance
13.3.2
Creepage dist
13.4
Comm.
1
2
Up
Urms
Req.
Measu.
Req.
Measu.
Basic Live Neutral
326V
230V
2,0mm
3,0mm
2,5mm
3,0mm
1)
Basic Live Neutral
326V
230V
2,0mm
4,0mm
2,5mm
4,0mm
2)
Reinforce Primary Chassis 326V 230V 4,0mm
6,0mm 5,0mm 6,0mm 3)
Reinforce Primary
Chassis 326V 230V 4,0mm
7,0mm 5,0mm 7,0mm 4)
Reinforce Primary
*) Chassis 326V 230V 4,0mm
6,0mm 5,0mm >
6,0mm
5)
Reinforce Primary
Secondary 344V 243V 4,0mm
6,0mm 5,0mm
6,0mm 6)
Reinforce Primary Secondary 384V 271V 4,0mm
6,0mm 5,6mm
6,0mm 7)
Reinforce
Primary
Chassis 326V 230V
4,0mm
7,0mm 5,0mm 7,0mm 8)
*) 2N force applied
Comments: 1) Measured on PCB before mains fuse (F101).
2) Measured on TRANS pcb after 6,3A mains fuse between CN12 connected copper traces
(Part of directly connected to the mains).
3) Measured on main pcb from pri. trace to metal chassis connenected sec. trace.
4) Measured between pri. trace for socket-outlet and near metal chassis (back cover).
5) Measured between primary solder pin and embossed metal chassis (bottom).
6) Measured on Stand-by pcb from pri. trace to secondary trace.
7) Measured on TRANS pcb from pri. trace to secondary trace.
8) Measured between
4) Measured between pri. trace for socket-outlet and near metal chassis (back cover).
5) Measured between primary solder pin and embossed metal chassis (bottom).
6) Measured on Stand-by pcb from pri. trace to secondary trace.
7) Measured on TRANS pcb from pri. trace to secondary trace.
8) Measured between
internal primary part of the mains switch
and near metal chassis (back cover).
IEC 60065 7ed. (2001)
- Page 3 of 3 -
www.nemko.com
Report No. 98503
14.3.3
Transformer/motor, constructional requirements
P
Transformer
Part No.
Part No.
Insulation
between
between
Insulation Res.
M Ohms
Test Volt
V (60 sec.)
Clearances / Creepage distances
Measured
Required
CLT(
or
KLT)5V048ZE
Pr - sec
> 100
3KV (rms)
7,3 / 7,3 mm
4,0 / 5,6 mm
Pr - ic
> 100
3KV (rms)
6,3 / 6,3 mm
4,0 / 5,0 mm
CLT(
or
KLT)5J033YE
Pr - Sec
> 100
3 kV (rms)
7,1 / 7,1 mm
4,0 / 5,0 mm
Pr - ic
> 100
3 kV (rms)
6,5 / 6,5 mm
4,0 / 5,0 mm
-
Components / construction
CLT(
or
KLT)5V048ZE
Windings on two separate bobbins. The bobbins are placed
in an insulating housing with two compartments, one above
the other. Bobbin thickness: > 0,4mm.
Max. Working Voltage: 384Vp/271Vrms
in an insulating housing with two compartments, one above
the other. Bobbin thickness: > 0,4mm.
Max. Working Voltage: 384Vp/271Vrms
P
Components / construction
CLT(
or
KLT)5J033YE
Windings on single bobbin. The center flange provided
between primary and secondary windings. Satisfactory
constructed. Bobbin thickness: > 0,4mm.
Max. Working voltage: 344Vp/243Vrms
between primary and secondary windings. Satisfactory
constructed. Bobbin thickness: > 0,4mm.
Max. Working voltage: 344Vp/243Vrms
P
Transformer
Part No
Part No
Insulation
Between
Between
Thick (mm)
X Number
Material
Dielectric strength test
60 sec.
CLT(
or
KLT)5V048ZE
Pr - sec
1,00 mm min. x 1
PET bobbin
Pass *)
Pr - ic
1,00 mm min. x 1
PET bobbin
Pass *)
CLT(
or
KLT)5J033YE
Pr - sec
0,50 mm min. x 2
0,50 mm min. x 1
0,50 mm min. x 1
PET bobbin wall
PBT bobbin cap.
PBT bobbin cap.
Pass *)
Pr - ic
0,60 mm min. x 1
PET bobbin
Pass *)
Pr - ic
0,50 mm min. x 1
PBT bobbin cap.
Pass *)
*) Test voltage: 3000 Vrms.
17.1
Torque test to Table 20:
P
Screw
Diameter
With
Without
Material
Torque test (Nm)
Location / function
(mm)
Head
Head
Screw
Nut
Fulfilled / Remarks
Fixing of top cover
(sides)
(sides)
4,0 x -
Metal
Metal
Tested with 1,2Nm,
5 times / Pass
5 times / Pass
Fixing of top cover
(rear)
(rear)
3,0 x -
Metal
Metal
Tested with 0,5Nm,
5 times / Pass
5 times / Pass
- Page 1 of 4 -
Photos
Report
No.
98503
Click on the first or last page to see other HK 3490 (serv.man2) service manuals if exist.