Harman Kardon HK 3390 EMC - CB Certificate ▷ View online
IEC 60065 7ed. (2001)
- Page 3 of 3 -
www.nemko.com
Report No. 98502
14.3.3
Transformer/motor, constructional requirements
P
Transformer
Part No.
Part No.
Insulation
between
between
Insulation Res.
M Ohms
Test Volt
V (60 sec.)
Clearances / Creepage distances
Measured
Required
CLT(
or
KLT)5U021ZE
Pr - sec
> 100
3KV (rms)
10,0 / 10,0mm
4,0 / 5,6 mm
Pr - ic
> 100
3KV (rms)
8,5 / 8,5 mm
4,0 / 5,0 mm
CLT(
or
KLT)5J033YE
Pr - Sec
> 100
3 kV (rms)
7,1 / 7,1 mm
4,0 / 5,0 mm
Pr - ic
> 100
3 kV (rms)
6,5 / 6,5 mm
4,0 / 5,0 mm
-
Components / construction
CLT(
or
KLT)5U021ZE
Windings on two separate bobbins. The bobbins are placed
in an insulating housing with two compartments,
one above the other. Bobbin thickness: > 0,4mm.
Max. operating voltage: 379Vp/268Vrms
in an insulating housing with two compartments,
one above the other. Bobbin thickness: > 0,4mm.
Max. operating voltage: 379Vp/268Vrms
P
Components / construction
CLT(
or
KLT)5J033YE
Windings on single bobbin. The center flange provided
between primary and secondary windings. Satisfactory
constructed. Bobbin thickness: > 0,4mm.
Max. operating voltage: 344Vp/243Vrms
between primary and secondary windings. Satisfactory
constructed. Bobbin thickness: > 0,4mm.
Max. operating voltage: 344Vp/243Vrms
P
Transformer
Part No
Part No
Insulation
Between
Between
Thick (mm)
X Number
Material
Dielectric strength test
60 sec.
CLT(
or
KLT)5U021ZE
Pr - sec
0,80 mm min. x 1
PET bobbin
Pass *)
Pr - ic
0,80 mm min. x 1
PET bobbin
Pass *)
CLT(
or
KLT)5J033YE
Pr - sec
0,50 mm min. x 2
0,50 mm min. x 1
0,50 mm min. x 1
PET bobbin wall
PBT bobbin cap.
PBT bobbin cap.
Pass *)
Pr - ic
0,60 mm min. x 1
PET bobbin
Pass *)
Pr - ic
0,50 mm min. x 1
PBT bobbin cap.
Pass *)
*) Test voltage: 3000 Vrms.
17.1
Torque test to Table 20:
P
Screw
Diameter
With
Without
Material
Torque test (Nm)
Location / function
(mm)
Head
Head
Screw
Nut
Fulfilled / Remarks
Fixing of top cover
(sides)
(sides)
4,0 x -
Metal
Metal
Tested with 1,2Nm,
5 times / Pass
5 times / Pass
Fixing of top cover
(rear)
(rear)
3,0 x -
Metal
Metal
Tested with 0,5Nm,
5 times / Pass
5 times / Pass
- Page 1 of 4 -
Photos
Report
No.
98502
- Page 2 of 4 -
Photos
Report
No.
98502
- Page 3 of 4 -
Photos
Report
No.
98502
Click on the first or last page to see other HK 3390 service manuals if exist.