Harman Kardon DVD 39 (serv.man2) EMC - CB Certificate ▷ View online
- Page 9 of 42 -
Report
No.
98390
6 HAZARDOUS
RADIATION
6.1
Ionizing radiation < 36 pA/kg (0,5 mR/h)
No lionizing radiation.
N/A
6.1
EN 60065
European Council Directive 96/29/Euratom of 13
May 1996 10cm from outer surface of apparatus
<1µSv/h (0,1mR/h)
May 1996 10cm from outer surface of apparatus
<1µSv/h (0,1mR/h)
N/A
6.2
Laser radiation, emission limits to IEC 60825-1 :
Measured wavelength
(CD/DVD):
*) 792nm / 657nm
**) 786nm / 653nm
(CD/DVD):
*) 792nm / 657nm
**) 786nm / 653nm
Measured power (CD/DVD):
*) 48,2uW / 57,5uW
**) 65,1uW / 69,4uW
AEL of Class 1 (CD/DVD):
*) 597uW / 390uW
**) 581uW / 390uW
*) 48,2uW / 57,5uW
**) 65,1uW / 69,4uW
AEL of Class 1 (CD/DVD):
*) 597uW / 390uW
**) 581uW / 390uW
Within AEL of Class 1 /
Class 1 Laser Product.
(Measured by JQA)
(Measured by JQA)
Note) Laser Pick-up type,
*) SF-HD65
**) SF-HD850
*) SF-HD65
**) SF-HD850
P
Emission limits under fault conditions ............. :
Measured wavelength
(CD/DVD):
*) 792nm / 657nm
**) 786nm / 653nm
(CD/DVD):
*) 792nm / 657nm
**) 786nm / 653nm
Measured power (CD/DVD):
*) 225uW / 285uW
**) 290uW / 311uW
*) 225uW / 285uW
**) 290uW / 311uW
AEL of Class 1 (CD/DVD):
*) 597uW / 390uW
**) 581uW / 390uW
*) 597uW / 390uW
**) 581uW / 390uW
Within AEL of Class 1 /
Class 1 Laser Product (inside)
(Measured by JQA)
Note) Laser Pick-up type,
*) SF-HD65
**) SF-HD850
*) SF-HD65
**) SF-HD850
P
- Page 10 of 42 -
Report
No.
98390
7
HEATING UNDER NORMAL OPERATING CONDITIONS
7.1
Temperature rises not exceeding specified values,
no operation of fuse links
no operation of fuse links
No fuse links operate during
normal operating operation.
See appended table
normal operating operation.
See appended table
P
7.1.1
Temperature rise of accessible parts
See appended table
P
7.1.2
Temperature rise of parts providing electrical
insulation
insulation
See appended table
P
7.1.3
Temperature rise of parts acting as a support or
as a mechanical barrier
as a mechanical barrier
See appended table
P
7.1.4
Temperature rise of windings
See appended table
P
7.1.5
Parts not subject to a limit under 7.1.1 to 7.1.4
See appended table
P
7.2
Softening temperature of insulating material
supporting parts conductively connected to the
mains carrying a current > 0,2 A at least 150
supporting parts conductively connected to the
mains carrying a current > 0,2 A at least 150
o
C
Approved components
according to relevant IEC
standards.
according to relevant IEC
standards.
N/A
8
CONSTRUCTIONAL REQUIREMENTS WITH REGARD TO THE PROTECTION
AGAINST ELECTRIC SHOCK
AGAINST ELECTRIC SHOCK
8.1
Conductive parts covered by lacquer, paper,
untreated textile oxide films and beads etc.
considered to be bare
untreated textile oxide films and beads etc.
considered to be bare
Considered
P
8.2
No shock hazard when changing voltage setting
device, fuse-links or handling drawers etc.
device, fuse-links or handling drawers etc.
Operation “By hand” not
possible
possible
N/A
8.3
Insulation of hazardous live parts not provided by
hygroscopic material
hygroscopic material
No hygroscopic materials
used
used
N/A
8.4
No risk of electric shock following the removal of
a cover which can be removed by hand
a cover which can be removed by hand
No cover removable by
hand
hand
N/A
8.5
Class I equipment
Class II apparatus.
N/A
Basic insulation between hazardous live parts and
earthed accessible parts
earthed accessible parts
N/A
Resistors bridging basic insulation complying
with 14.1 a)
with 14.1 a)
N/A
8.6
Class II equipment and Class II constructions
within Class I equipment
within Class I equipment
Class II apparatus.
P
- Page 11 of 42 -
Report
No.
98390
Reinforced or double insulation between
hazardous live parts and accessible parts
hazardous live parts and accessible parts
Double/Reinforced
insulation complies with
requirements specified in
clause 10 and 13.
insulation complies with
requirements specified in
clause 10 and 13.
P
Components bridging reinforced or double
insulation complying with 14.1 a) or 14.3
insulation complying with 14.1 a) or 14.3
The apparatus has
isolating transformers.
isolating transformers.
P
Basic and supplementary insulation each being
bridged by a capacitor complying with 14.1 a)
bridged by a capacitor complying with 14.1 a)
No such capacitors.
N/A
Reinforced or double insulation being bridged
with 2 capacitors in series complying with
14.2.1 a)
with 2 capacitors in series complying with
14.2.1 a)
No such capacitors.
N/A
Reinforced or double insulation being bridged
with a single capacitor complying with 14.2.1 b)
with a single capacitor complying with 14.2.1 b)
Y
1
capacitors, CY91,
CY92, CY93 and CY94;
inside the enclosure.
inside the enclosure.
P
Basic insulation bridged by components
complying with 14.3.4.3
complying with 14.3.4.3
No such components.
N/A
8.7
This clause is void
—
8.8
Basic or supplementary insulation > 0,4 mm (mm)
................................................................................. :
................................................................................. :
N/A
Reinforced
insulation > 0,4 mm (mm) ............... :
a.
Sheet of insulation in
top side of the SMPS
between primary and
metal chassis (top cover).
Tested acc. to cl. 10.3 - OK.
between primary and
metal chassis (top cover).
Tested acc. to cl. 10.3 - OK.
b. Transformer bobbin
thickness: > 0,4mm
Tested acc. to cl. 10.3.-OK.
See list of critical comp.
Tested acc. to cl. 10.3.-OK.
See list of critical comp.
c. Optocouplers inner
insulation, ref. 14.11.
P
Thin sheet insulation (excluding non-separable
thin sheet insulation. See 8.22)
thin sheet insulation. See 8.22)
P
Basic or supplementary insulation, at least two
layers, each meeting 10.3
layers, each meeting 10.3
N/A
Basic or supplementary insulation, three layers
any two of which meet 10.3
any two of which meet 10.3
N/A
- Page 12 of 42 -
Report
No.
98390
Reinforced insulation, two layers each of which
meet 10.3
meet 10.3
N/A
Reinforced insulation, three layers any two which
meet 10.3
meet 10.3
Insulation in TF91 and
TF92 transf. between pri.
and sec. windings.
TF92 transf. between pri.
and sec. windings.
P
8.9
Adequate insulation between internal hazardous
live conductors and accessible parts
live conductors and accessible parts
Double insulated.
P
Adequate insulation between internal hazardous
live parts and conductors connected to
accessible parts
live parts and conductors connected to
accessible parts
Single insulation but
safely anchored.
safely anchored.
P
8.10
Double insulation between conductors connected
to the mains and accessible parts.
to the mains and accessible parts.
Double insulation between internal hazardous
live parts and conductors connected to accessible
parts.
live parts and conductors connected to accessible
parts.
Double insulated,
tested according to 8.9
and 10.3.
tested according to 8.9
and 10.3.
P
8.11
Detaching of wires
P
No undue reduction of creepages or clearance
distances if wires become detached
distances if wires become detached
Inlet connected wires
hooked-in before soldered.
Other end of the inlet wires
are connected with
multi-contact housing.
hooked-in before soldered.
Other end of the inlet wires
are connected with
multi-contact housing.
P
Vibration
test
carried out ..................................... :
See 12,1,2
N/A
8.12
This clause is void
—
8.13
Adequate fastening of windows, lenses, lamp
covers etc. (pull test 20 N for 10 s)
covers etc. (pull test 20 N for 10 s)
Adequately fastened.
P
8.14
Adequate fastening of covers (pull test 50 N for
10 s)
10 s)
Covers adequately
fastened with screws.
fastened with screws.
P
8.15
No risk of damage to the insulation of internal
wiring due to hot parts or sharp edges
wiring due to hot parts or sharp edges
Wires safely anchored
away from parts with high
temperature.
away from parts with high
temperature.
P
8.16
Only special supply equipment can be used
Not supplied by a special
supply apparatus.
supply apparatus.
N/A
8.17
Insulated winding wire without additional
interleaved insulation
interleaved insulation
No such winding wire.
N/A
8.18
Endurance test as required by 8.17
N/A
Click on the first or last page to see other DVD 39 (serv.man2) service manuals if exist.