Harman Kardon BDS 275 (serv.man2) EMC - CB Certificate ▷ View online
R
AUDIX Technology (Shenzhen) Co., Ltd.
Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-E12377 page 53 of 323
R
AUDIX Technology (Shenzhen) Co., Ltd.
Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-E12377 page 54 of 323
R
AUDIX Technology (Shenzhen) Co., Ltd.
Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-E12377 page 55 of 323
6. DISTURBANCE POWER TEST
6.1. Test Equipments
Item
Equipment
Manufacturer
Model No.
Serial No.
Last Cal. Cal. Interval
1. Test Receiver Rohde & Schwarz
ESPI
100423
May.08, 12
1 Year
2. Absorbing Clamp Rohde & Schwarz MDS-21
100096
Nov.30,11
1 Year
3.
N50(f-m) 6dB
Fixed Attenuator
Agilent 8491A
MY39264395
Nov.30,11
1
Year
4. RF
Cable
MIYAZAKI 5D-2W
NO.1
Nov.30,11 1
Year
6.2. Block Diagram of Test Setup
6.3. Disturbance Power Limit
All emanations from devices or system including any network of conductors and apparatus
connected thereto, shall not exceed the level of field strengths specified below:
connected thereto, shall not exceed the level of field strengths specified below:
Interference Power Limits dB(pW)
Frequency
MHz
Quasi-peak Value
Average Value
30 ~ 300
45 Increasing Linearly
with Frequency to 55
(Q.P.)
35 Increasing Linearly
with Frequency to 45
(A.V.)
6.4. EUT Configuration on Test
The configuration of EUT is the same as used in conducted emission test. Please refer to
Section 3.5.
6.5. Operating Condition of EUT
6.5.1. Setup the EUT and simulators as shown in Section 6.2.
6.5.2. Turn on the power of all equipments.
6.5.3. Let the EUT worked in test mode (BD Play/USB Play/BD Live/FM Mode/Coaxial
6.5.2. Turn on the power of all equipments.
6.5.3. Let the EUT worked in test mode (BD Play/USB Play/BD Live/FM Mode/Coaxial
In/ AUX In / Component Video IN/ Optical In / HDMI In) and test it.
EUT
Sub Clamp
Absorbing Clamp
Test Receiver
AC Mains
6.0m
0.8m
R
AUDIX Technology (Shenzhen) Co., Ltd.
Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-E12377 page 56 of 323
6.6. Test Procedure
The EUT is placed on a table which is 0.8m high above the ground and away from other
metallic surface at least 0.8m. It is connected to the power mains through an extension cord
of 6m min. The absorber clamp clamps the cord and moves from the far end to the EUT to
measure the disturbing energy emitted from the cord.
The bandwidth of the test receiver(R&S ESPI) is set at 120kHz.
All the test results are listed in Section 6.7.
of 6m min. The absorber clamp clamps the cord and moves from the far end to the EUT to
measure the disturbing energy emitted from the cord.
The bandwidth of the test receiver(R&S ESPI) is set at 120kHz.
All the test results are listed in Section 6.7.
6.7. Disturbance Power Test Result
PASS. (All emissions not reported below are too low against the prescribed limits.)
The EUT with the following test modes were tested and the test modes were selected to read
Q.P and average values, all the test results are listed in next pages.
Q.P and average values, all the test results are listed in next pages.
EUT: BLU-RAY DISC SYSTEM Model No. : BDS575
Test Date: Jul.02, 2012 Temperature: 24.7℃ Humidity:65%
The details of test modes are as follows:
No.
Test Mode
Reference Test Data No.
1 BD
Play
#1
2 USB
Play
#2
3 AUX
In
#3
4 HDMI
In
#4
5 Coaxial
In
#5
6 Optical
In
#6
7
AC Line
Component Video In
#7
8
Component Video In
#8
9 Coaxial
In
#9
10 BD
Play
#10
11 USB
Play
#11
12 AUX
In
#12
13 HDMI
In
#13
14
Center Speaker
Coaxial In
#14
15 Coaxial
In
#15
16 Optical
In
#16
17 HDMI
In
#17
18 AUX
In
#18
19
Front Speaker L
BD Play
#19
Click on the first or last page to see other BDS 275 (serv.man2) service manuals if exist.