DOWNLOAD Harman Kardon AVR 235 (serv.man2) Service Manual ↓ Size: 3.86 MB | Pages: 115 in PDF or view online for FREE

       

DIGITAL EMC CO., LTD.      

Page 5 of 19 

Test Report   

 

 

     

 

 

Kind of Equipment 

: A/V Receiver 

Model Number 

: AVR4600 

Brand Name 

: HARMAN KARDON 

Serial No. 

: None 

Type of Sample Tested 

: Pre-Production 

Rating Power Supply 

: AC 230V, 50Hz, 350W 

High Frequency 

: 4.332MHz(RPS CLK), 5MHz(Micom CLK), 
  10MHz(Micom CLK), 14.318MHz(OSD CLK), 
 17.734MHz(OSD CLK), 
  12.288MHz(Surround DSP CLK) 

 

 

Applicant 

: ANAM ELECTRONICS CO.,LTD. 

645, sungkok-Dong, AnSan-City, KyungKi-Do, 
Korea 425-110 

 

 

Manufacturer 

: 1. ANAM ELECTRONICS CO.,LTD. 

645, sungkok-Dong, AnSan-City, KyungKi-Do, 
Korea 425-110 
2. DongGuan LiaoBu Anam Electronics 
Xin Cheng Management Area, LiaoBu Town, 
DongGuan City, GuangDong Province, China 

 

Date of Receipt of Sample 

: 2003-06-03 

 

#683-3,Yubang-Dong, Yongin-Si,Kyunggi-Do,Korea,449-080

 

       

DIGITAL EMC CO., LTD.      

Page 6 of 19 

Test Report   

 

 

           

 

4.1 Principle of Configuration Selection 

Emission  : The equipment under test (EUT) was configured to measure its highest possible 
radiation level. The test modes were adapted accordingly in reference to the instructions for 
use. 
Immunity  : The equipment under test (EUT) was configured to have its highest possible 
susceptibility against the tested phenomena. The test modes were adapted accordingly in 
reference to the instructions for use.   
 

4.2 Test Operation modes 

1.  Connected the monitor by A/V cable. 
2.  Test CD is played.   

         

4.3 Support Equipment Used 

 

TYPE 

MANUFACTURER 

MODEL NO. 

SERIAL NO. 

Note 

CD Player 

ANAM 

CDP2025 

N/A 

Power cable 1.8m Non-Shield 

A/V cable 1.6m Shield

 

Speaker LG 

N/A 

N/A 

Power cable 1.8m Non-Shield 

A/V cable 1.6m Shield

 

     
 

 NOTE 
- See “APPENDIX 2 photographs” for actual system test setup

 

#683-3,Yubang-Dong, Yongin-Si,Kyunggi-Do,Korea,449-080

 

       

DIGITAL EMC CO., LTD.      

Page 7 of 19 

Test Report   

 

 

 

5.1 List of Test and Measurement   

Signal Generator (SMY01) 

DE24241 

R&S 

2004.01 

RF Power Meter(NRVD) 

DE30994 

R&S 

2004.01 

Function Generator(33120A) 

US3602592 

EMC Automation 

2004.01 

System Interface(SI300) 

010401 

EMC Automation 

N/A 

Switch Controller(RSM-2) 

010101 

EMC Automation 

N/A 

Amplifier 80~100MHz(100W1000M1) 

20213 

Amplifier Research 

2003.11 

Amplifier 10kHz ~250MHz(75A250M1) 

24270 

Amplifier Research 

2003.11 

  Amplifier  10kHz~220MHz(AR1000L) 

29370 

Amplifier Research 

N/A 

Field Probe 10kHz ~ 1GHz(FP4000) 

23376 

Amplifier Research 

N/A 

Field Probe 10kHz ~ 1GHz(HI4422) 

101389 

Holaday Inc. 

N/A 

Antenna 80~1000MHz(LPD-80) 

98023 

EMC Automation 

N/A 

Antenna 25~150MHz(HLP2515) 

120900 

EMC Automation 

N/A 

CDN (801-M1-16A) 

9832 

FCC 

2004.01 

single power Mains(801-M2-16A) 

9863 

FCC 

2004.01 

Two power Mains801-M3-16A) 

98119 

FCC 

2004.01 

Three Power Mains801-M5-50A) 

2026 

FCC 

2004.01 

Five power Mains(S9) 

9865 

FCC 

2004.01 

Singnal Lines, 9 Pins(S15) 

9866 

FCC 

2004.01 

Signal Lines, 15 Pins(S25) 

9867 

FCC 

2004.01 

Signal Lines, 25 Pins (36S) 

9868 

FCC 

2004.01 

Signal Lines, 36 Pins(801-150-50-C) 

98161,98162 

FCC 

2004.01 

Impedance Matching Unit(DN) 

2055 

FCC 

2004.01 

Balanced with Shorting Adapters(801-T8) 

2030 

FCC 

2004.01 

Unbalanced , Unshielded Line   

CDN with Shorting Adapter (801-AF8)

 

2027 FCC 

2004.01 

Coaxial Line CDN with Shorting Adapters(801-C-N-50) 

435 FCC 

2004.01 

EM Injection Clamp(F2031-32mm) 

241 

FCC 

N/A 

Clamp On Injection probeF-120-9A) 

605 

FCC 

N/A 

Clamp On Current Probe(F-33-1) 

N/A 

N/A 

N/A 

#683-3,Yubang-Dong, Yongin-Si,Kyunggi-Do,Korea,449-080

 

       

DIGITAL EMC CO., LTD.      

Page 8 of 19 

Test Report   

 

 

5.2  Electrostatic discharge 

 

RESULT :

                                                                                                              Pass 

 
5.2.1 Measurement Procedure

 

The immunity against electrostatic discharge was tested in accordance with 
EN55020:1994+A11:1996 +A12,A13,A14:1999. A ground reference plane was located on 
the floor, and connected to earth via a low impedance connection. The return cable of the ESD 
generator was connected to the reference plane. In case of  a table top equipment, EUT was 
placed on the reference plane on 80cm of insulating support. And a vertical coupling plane 
(VCP) of 0.5*0.5m was located 10cm from the EUT’s sides. The VCP was connected to the 
reference plane via a cable with a 470㏀(2EA) resistor. The test was made by applying contact 

and air discharges to the EUT itself, and contact discharges to the VCP/HCP. When applying the 
discharges to the VCP the tip of the generator was located at the middle edge of the VCP. The 
VCP was located 10cm from each side of the EUT. Contact discharges of ±4kV were applied to 
various points of the EUT at conductive surfaces, and to the VCP. Air discharges of ±8kV were 

applied to various points of the EUT at non-conductive surfaces. 
 

Severity level 

: 2 (Contact Discharge) 

3 (Air Discharge) 

Test voltages 

: ±4.0㎸ (Contact Discharge) 

±

8.0㎸ (Air Discharge) 

EUT Type 

: Unground equipment 

Number of 

Contact

 discharges 

Number of 

Air 

discharges 

:

>total 200 discharges(100 each at negative and positive) 

> 10 discharges 

Test Method 

: The charge on the EUT shall be removed prior to each 

applied ESD pulse. 

Performance criterion 

: B 

 

5.2.2 List of Test and Measurement Instruments 

 

Electrostatic discharge 

BEST EMC 

BEST EMCV2.7 200122-043SC 

SCHAFFNER 

2003.09 

ESD GUN 

BEST-ESD 

1072 

SCHAFFNER 

2003.09 

PC 

emachines/AC  50035 045 00056  COMPUTOWN 

N/A 

 

#683-3,Yubang-Dong, Yongin-Si,Kyunggi-Do,Korea,449-080