Harman Kardon AVR 171 (serv.man5) EMC - CB Certificate ▷ View online
Page 21 of 52
Report No.: 232174
IEC 60065
Clause Requirement
+
Test
Result
Verdict
TRF No. IEC60065K
14.4.1
High voltage transformers and multipliers tested as
part of the submission
part of the submission
N/A
14.4.2
High voltage assemblies and other parts tested as
part of the submission
part of the submission
N/A
14.5 Protective
devices
P
Protective devices used within their ratings
Thermal cut-outs and fuse
P
External clearances and creepage distances meet
requirement of clause 13 for the voltage across the
device when opened
requirement of clause 13 for the voltage across the
device when opened
Certified protective devices
applied (thermal cut-outs and
fuse)
See appended table, list of
critical components.
applied (thermal cut-outs and
fuse)
See appended table, list of
critical components.
P
14.5.1.1
a) Thermal cut-outs separately approved
TS92 thermal cut-out is
approved component
according to IEC 60730-1.
See appended table, list of
critical components.
approved component
according to IEC 60730-1.
See appended table, list of
critical components.
P
b) Thermal cut-outs tested as part of the submission
N/A
14.5.1.2
a) Thermal links separately approved
No thermal links
N/A
b) Thermal links tested as part of the submission
N/A
14.5.1.3
Thermal devices re-settable by soldering
No thermal device re-settable
by soldering
by soldering
N/A
14.5.2.1
Fuse-links in the mains circuit according to IEC
60127
60127
Fuse is approved according
to IEC 60127.
See appended table, list of
critical components.
to IEC 60127.
See appended table, list of
critical components.
P
14.5.2.2
Correct marking of fuse-links adjacent to holder ... :
Marked on PCB adjacent to
fuse as;
F901: T 6.3A H 250V
fuse as;
F901: T 6.3A H 250V
P
14.5.2.3
Not possible to connect fuses in parallel ............... :
No possible to connect fuses
in parallel.
in parallel.
P
14.5.2.4
Not possible to touch hazardous live parts when
replacing fuse-links without the use of a tool ......... :
replacing fuse-links without the use of a tool ......... :
No replacement of fuse
possible by hand
possible by hand
P
14.5.3
PTC thermistors comply with IEC 60730-1:2007
PTC thermistor, F201 for USB
port, comply with IEC 60730-1
port, comply with IEC 60730-1
P
PTC devices (15 W) category V-1 or better
< 15W
N/A
14.5.4 Circuit
protectors
have adequate breaking capacity
and their position is correctly marked
Only standard fuse and
protector used.
protector used.
N/A
14.6
Switches
No mains switch.
N/A
Page 22 of 52
Report No.: 232174
IEC 60065
Clause Requirement
+
Test
Result
Verdict
TRF No. IEC60065K
14.6.1 a)
Separate testing to IEC 61058-1 including:
- 10 000 operations
- Normal pollution suitability
- Make and break speed independent of speed of
actuation
V-0 compliance with annex G, G.1.1
- 10 000 operations
- Normal pollution suitability
- Make and break speed independent of speed of
actuation
V-0 compliance with annex G, G.1.1
N/A
14.6.1 b)
Tested in the apparatus:
N/A
Switch controlling > 0.2A with open contact voltage
> 35 V (peak)/24 V dc complying with 14.6.3, 14.6.4
and V-0 in annex G, G.1.1
> 35 V (peak)/24 V dc complying with 14.6.3, 14.6.4
and V-0 in annex G, G.1.1
N/A
Switch controlling > 0.2A with open contact voltage
< 35 V (peak)/24 V dc complying with 14.6.3 and V-0
in annex G, G.1.1
< 35 V (peak)/24 V dc complying with 14.6.3 and V-0
in annex G, G.1.1
N/A
Switch controlling < 0.2A with open contact voltage
> 35 V (peak)/24 V dc complying with 14.6.4 and
V-0 in annex G, G.1.1
> 35 V (peak)/24 V dc complying with 14.6.4 and
V-0 in annex G, G.1.1
N/A
14.6.2
Switch tested to 14.6.1 b) constructed to IEC 61058-
1 subclause 13.1 and has making/breaking action
independent of speed of actuation
1 subclause 13.1 and has making/breaking action
independent of speed of actuation
N/A
14.6.3
Switch tested to 14.6.1 b) compliant with IEC 61058-
1 subclause 16.2.2 d) and m) not attaining
excessive temperatures in use
1 subclause 16.2.2 d) and m) not attaining
excessive temperatures in use
N/A
14.6.4
Switch tested to 14.6.1 b) has adequate dielectric
strength
strength
N/A
14.6.5
Mains switch controlling mains socket outlets
additional tests to IEC 61058-1
additional tests to IEC 61058-1
N/A
Socket outlet current marking correct
No mains socket-outlets
N/A
14.7
Safety interlocks
No safety interlocks
N/A
Safety interlocks to 2.8 of IEC 60950-1
N/A
14.8
Voltage setting devices and the like
No voltage setting devices
N/A
Voltage setting device not likely to be changed
accidentally
accidentally
N/A
14.9
Motors
No AC motors
Brushless DC FAN motor only.
Brushless DC FAN motor only.
P
14.9.1
Endurance test on motors
N/A
Motor start test
N/A
Dielectric strength test
Only DC supplied.
N/A
14.9.2
Not adversely affected by oil or grease etc.
The motor for fans are not
adversely affected by oil or
grease or other substances.
adversely affected by oil or
grease or other substances.
P
Page 23 of 52
Report No.: 232174
IEC 60065
Clause Requirement
+
Test
Result
Verdict
TRF No. IEC60065K
14.9.3
Protection against moving parts
The fans are placed inside the
unit. No access.
unit. No access.
P
14.9.4
Motors with phase-shifting capacitors, three-phase
motors and series motors meet clause. B.8, B.9 and
B.10 of IEC 60950-1, Annex B
motors and series motors meet clause. B.8, B.9 and
B.10 of IEC 60950-1, Annex B
N/A
14.10 Batteries
No
batteries
N/A
14.10.1
Batteries mounted with no risk of accumulation of
flammable gases
flammable gases
N/A
14.10.2
No possibility of recharging non-rechargeable
batteries
batteries
N/A
14.10.3
Recharging currents and times within manufacturers
limits
limits
N/A
Lithium batteries discharge and reverse currents
within the manufacturers limits
within the manufacturers limits
N/A
14.10.4
Battery mould stress relief
N/A
14.10.5
Battery drop test
N/A
14.11 Optocouplers
Optocouplers are approved
components.
components.
External creepage/clearance
distances are min. 7.7 mm.
Internal creepage/clearance
distances are min. 6.0 mm, or
thermal cycling test is covered
by SEMKO
DTI: Min. 0.4 mm.
See appended table, list of
critical components.
distances are min. 7.7 mm.
Internal creepage/clearance
distances are min. 6.0 mm, or
thermal cycling test is covered
by SEMKO
DTI: Min. 0.4 mm.
See appended table, list of
critical components.
P
a) Comply with 13.6 (jointed insulation) and N.2.1
N/A
b) Comply with IEC 60747-5-5:2007
N/A
Alternative to a) and b) optocoupler comply with 13.8
N/A
14.12
Surge suppression varistors
P
Comply with IEC 61051-2
Varistor, VT91 and VT92
comply with IEC 61051-2.
comply with IEC 61051-2.
P
Not connected between mains and accessible parts
except for earthed parts of permanently connected
apparatus
except for earthed parts of permanently connected
apparatus
N/A
Complies with the current pulse, fire hazard and
thermal stress requirements of 14.12
thermal stress requirements of 14.12
A certified varistor used
N/A
Page 24 of 52
Report No.: 232174
IEC 60065
Clause Requirement
+
Test
Result
Verdict
TRF No. IEC60065K
15 Terminals
15.1.1
Mains plug, appliance inlet, interconnection couplers
and mains socket-outlet meet the appropriate
standard
and mains socket-outlet meet the appropriate
standard
Approved cord set and
appliance inlet provided.
See appended table, list of
critical components, and
summary of testing.
appliance inlet provided.
See appended table, list of
critical components, and
summary of testing.
P
Overloading of plugs or appliance inlets prevented if
the apparatus has mains socket outlets
the apparatus has mains socket outlets
No mains socket outlets
N/A
Overloading of internal wiring prevented if the
apparatus has mains socket outlets
apparatus has mains socket outlets
No mains socket outlets
N/A
15.1.2
Connectors for antenna, earth, audio, video or
data
data
See below.
P
No risk of insertion in mains socket-outlets
Only RCA, Antenna, Optical,
Network, HDMI and mini jacks
terminals used.
Banana plug type speaker
terminal also used, but they
are accepted due to below
note.
Network, HDMI and mini jacks
terminals used.
Banana plug type speaker
terminal also used, but they
are accepted due to below
note.
Note)
Banana plug type speaker
terminals are blocked in their
axial holes to prevent use of
plugs that can make
permanent contact with a
mains socket outlet
Banana plug type speaker
terminals are blocked in their
axial holes to prevent use of
plugs that can make
permanent contact with a
mains socket outlet
P
No risk of insertion into audio- or video- outlets
marked with the symbol of 5.2
marked with the symbol of 5.2
No sockets indicated with
the symbol
the symbol
N/A
15.1.3
Output terminals of a.c. adaptors or similar devices
not compatible with household mains socket-outlets
not compatible with household mains socket-outlets
Not adaptors used
N/A
15.2
Provision for protective earthing
Accessible conductive parts of Class I equipment
reliably connected to earth terminal, within
equipment
reliably connected to earth terminal, within
equipment
Class II equipment.
N/A
Protective earth conductors correctly coloured
N/A
Equipment with non-detachable mains cord provided
with separate protective earth terminal near mains
input
with separate protective earth terminal near mains
input
N/A
Protective earth terminal resistant to corrosion
N/A
Earth resistance test: < 0,1
at 25 A ................... :
N/A
15.3
Terminals for external flexible cords and for
permanent connection to the mains supply
permanent connection to the mains supply
Appliance inlet applied
N/A
Click on the first or last page to see other AVR 171 (serv.man5) service manuals if exist.