DOWNLOAD Sony DCR-HC62 / DCR-HC62E (serv.man4) Service Manual ↓ Size: 1.91 MB | Pages: 74 in PDF or view online for FREE

6-36

DCR-HC62/HC62E_ADJ

Order Page Address Data

Procedure

1

Check that the picture frame
is “AWB Adjustment Frame”.
If not,  perform “13. Picture
Frame Setting (AWB
Adjustment Frame)”

2

0

01

01

3

6

02

Check the data is “00”.
(Note 4)

4

0

10

06

5

F

44

2A

Press PAUSE (Write) button.

(6F)

6

F

45

Set the following data, and
press PAUSE (Write) button.

4E: NTSC model
AE: PAL model

7

F

46

5C

Press PAUSE (Write) button.

(6F)

8

F

47

98

Press PAUSE (Write) button.

(6F)

9

Place the C14 filter on the
lens.

10

0

10

00

11

6

01

47

Press PAUSE (Write) button.

12

6

01

45

Press PAUSE (Write) button.
(Note 5)

13

6

02

Check the data changes to
“01”.

Note 4: If not, select page: 6, address: 01, set data: 00, and press

PAUSE (Write) button.

Note 5: The adjustment data will be automatically input to page:

6F, address: 32 to 35, F4 to F7.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE (Write) button.

2

0

01

00

3

Remove the C14 filter on the
lens.

Adjust to the proper auto white balance output data.
If it is not correct, auto white balance and color reproducibility
will be poor.

Subject

Clear chart
(AWB Adjustment Frame) (Note 3)

Filter

Filter C14 for color temperature
correction

Adjustment Page

6F

Adjustment Address

32 to 35, 44 to 47, F4 to F7

Note 1: Perform “F No. & ND Light Quality Standard Data In-

put” and “Auto White Balance Standard Data Input” be-
fore this adjustment.

Note 2: If reading/writing data on pages 6F, set data: 06 to page:

0, address: 10, and then select pages: F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.

Note 3: Perform “13. Picture Frame Setting (AWB Adjustment

Frame)” before this adjustment.

Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ..................................... OFF
6) FOCUS (Menu setting) .......................................... MANUAL

(6F)

6-37

DCR-HC62/HC62E_ADJ

Order Page Address Data

Procedure

1

Check that the picture frame
is “AWB Adjustment Frame”.
If not, perform “13. Picture
Frame Setting (AWB
Adjustment Frame)”

2

6

02

Check the data is “00”.
(Note 4)

Auto white balance check

3

6

01

C1

Press PAUSE (Write) button.

4

6

02

Check the data changes to
“01”.

5

6

0C

Check the data is “00”.

6

6

01

00

Press PAUSE (Write) button.

InOut data check

7

Place the ND filter 1.5 (1.0 +
0.4 + 0.1) on the lens.

8

6

01

4B

Press PAUSE (Write) button

9

6

02

Check the data changes to
“01”.

10

6

0C

Check the data is “00”.

11

Remove the ND filter 1.5
(1.0 + 0.4 + 0.1) on the lens.

Note 4: If not, select page: 6, address: 01, set data: 00, and press

PAUSE (Write) button.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE (Write) button.

Subject

Clear chart
(AWB Adjustment Frame) (Note 3)

Filter

ND filter 1.0, 0.4 and 0.1

Measuring Instrument

Adjusting remote commander

Specified Value

Data of page: 6, address: 0C is “00”

Note 1: Perform “Color Reproduction Adjustment” and “Auto

White Balance Adjustment” before this adjustment.

Note 2: Check that the data of page: 0, address: 10 is “00”.
Note 3: Perform “13. Picture Frame Setting (AWB Adjustment

Frame)” before this adjustment.

Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ..................................... OFF
6) FOCUS (Menu setting) .......................................... MANUAL

Precautions on the Parts Replacement
There are two types of repair parts.

Type A

ENC03MA

Type B

ENC03MB

Replace the broken sensor with a same type sensor. If replace with
other type parts, the image will vibrate up and down or left and
right during hand-shake correction operations.

Precautions on Angular Velocity Sensor
The sensor incorporates a precision oscillator. Handle it with care
as if it dropped, the balance of the oscillator will be disrupted and
operations will not be performed properly.

Subject

Not required

Measurement Point

Displayed data of page: 1 (Note 1)

Measuring Instrument

Adjusting remote commander

Specified value

PITCH data: 2680 to 5080
YAW data: 2680 to 5080

Note 1: The right four digits of the page: 1 displayed data of the

adjusting remote commander.

1 : XX : XX

Displayed data

Note 2: Check that the data of page: 0, address: 10 is “00”.

Switch setting
1) ZOOM ..................................................................... TELE end
2) STEADY SHOT (Menu setting) ....................................... ON

Order Page Address Data

Procedure

  PITCH sensor output check (SE7002 of CD-672 board)

1

0

03

11

2

1

With the set in still state,
check that the displayed data
(Note 1) satisfies the PITCH
data specified value.

  YAW sensor output check (SE7001 of CD-672 board)

3

0

03

12

4

1

With the set in still state,
check that the displayed data
(Note 1) satisfies the YAW
data specified value.

5

0

03

00

  Steady shot operation check

6

Shake the set vertically and
horizontally to check that the
steady shot function operates
normally.

6-38

DCR-HC62/HC62E_ADJ

Order Page Address Data

Procedure

1

0

01

01

2

C

71

00

Press PAUSE (Write) button.

3

3

03

FF

Press PAUSE (Write) button.

4

3

01

5A

Press PAUSE (Write) button.
(Note 4)

5

3

02

Check the data changes to “00”.

6

3

03

Check the data is “00”. (Note 5)

7

C

3F

Read the data and this data is
named D

3F

.

8

Convert D

3F

 to decimal

notation, and obtain D

3F

’.

(Note 6)

9

Calculate D

40

’ using

following equations.
(decimal calculation)
D

40

’ = D

3F

’ + 10 (NTSC model)

D

40

’ = D

3F

’ – 10 (PAL model)

10

Convert D

40

’ to a hexadeci-

mal number, and obtain D

40

.

(Note 6)

11

C

40

D

40

Press PAUSE (Write) button.

12

C

71

41

Press PAUSE (Write) button.

13

0

01

00

Note 4: The adjustment data will be automatically input to page:

C, address: 3F and 47.

Note 5: If the data change to “01”, adjustment has error. Contents

of error is written into page: 3, address: C6. See the fol-
lowing table.

Note 6: Refer to table 6-4-1. “Hexadecimal-decimal conversion

table”.

Data of page: 3, address: C6

Contents of error

5E

VCO adjustment error

61

Contrast adjustment error

Before perform the electronic viewfinder system adjustments,
check that the data of page: 0, address: 10 is “00”. If not, select
page: 0, address: 10, and set the data “00”.
Note 1: Taken an extreme care not to destroy the liquid crystal

display module by static electricity when replacing it.

Note 2: Perform the following data setting before the viewfinder

system adjustments.
1) Select page: 3, address: C4, and set data: 69.
2) Select page: 3, address: C5, and set data: 02.
Reset the data after completing adjustment.
1) Select page: 3, address: C4, and set data: 00.
2) Select page: 3, address: C5, and set data: 00.

This adjustment does the following items automatically.

  VCO Adjustment
  Contrast Adjustment

Mode

VTR stop (PLAY/EDIT mode)

Signal

No signal

Adjustment Page

C

Adjustment Address

3F, 40 (VCO Adjustment)
47 (Contrast Adjustment)

Note 1: Perform this adjustments after perfoming “IC4701 Au-

tomatic adjustment”.

Note 2: Check that the data of page: 0, address: 10 is “00”.
Note 3: NTSC model: DCR-HC62

PAL model: DCR-HC62E

Switch setting
WIDE SELECT ......................................................................... 4:3

6-39

DCR-HC62/HC62E_ADJ

Correct the white balance.
If deviated, the EVF screen color cannot be reproduced.

Mode

VTR stop (PLAY/EDIT mode)

Signal

No signal

Measurement Point

Check on EVF screen

Measuring Instrument

Adjustment Page

C

Adjustment Address

45, 46

Specified Value

EVF screen must not be colored

Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Check the white balance only when replacing the fol-

lowing parts. If necessary, adjust them.

1. LCD panel
2. Light induction plate
3. IC7001

Order Page Address Data

Procedure

1

0

01

01

2

C

45

85

Press PAUSE (Write) button.

3

C

46

7A

Press PAUSE (Write) button.

4

Check that the EVF screen is
not colored. If not colored,
proceed to step 6.

5

C

45

Change the data so that the

46

EVF screen is not colored.
(Note 3)

6

0

01

00

Note 3: To write in the non-volatile memory (EEPROM), press

the PAUSE (Write) button each time to set the data.