Sony DCR-HC62 / DCR-HC62E (serv.man4) Service Manual ▷ View online
6-28
DCR-HC62/HC62E_ADJ
7.
F No. & ND Light Quality Standard Data Input
RadarW
RadarW
RadarW
RadarW
RadarW
Correct the lens iris and dispersion of the ND filter light quantity.
Subject
Clear chart (Center frame)
(40 cm (PTB-1450) from the front of
lens)
(40 cm (PTB-1450) from the front of
lens)
Adjustment Page
6F
Adjustment Address
1C to 23
Note 1: If reading/writing data on pages 6F, set data: 06 to page:
0, address: 10, and then select pages: F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Switch setting
1) WIDE SELECT .................................................................. 4:3
1) WIDE SELECT .................................................................. 4:3
Adjusting method:
8.
MAX GAIN Adjustment
RadarW
RadarW
RadarW
RadarW
RadarW
Setting the minimum illumination.
If it is not consistent, the image level required for taking subjects
in low illuminance will not be produced (dark).
If it is not consistent, the image level required for taking subjects
in low illuminance will not be produced (dark).
Subject
Clear chart (Center frame)
(40 cm (PTB-1450) from the front of
lens)
(40 cm (PTB-1450) from the front of
lens)
Adjustment Page
6F
Adjustment Address
2C
Note 1: Perform “Flange Back Adjustment” before this adjust-
ment.
Note 2: Check that the data of page: 0, address: 10 is “00”.
Note 3: NTSC model: DCR-HC62
Note 3: NTSC model: DCR-HC62
PAL model: DCR-HC62E
Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) ZOOM .................................................................... WIDE end
5) DIGITAL ZOOM (Menu setting) .................................... OFF
6) STEADY SHOT (Menu setting) ..................................... OFF
7) FOCUS (Menu setting) .......................................... MANUAL
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) ZOOM .................................................................... WIDE end
5) DIGITAL ZOOM (Menu setting) .................................... OFF
6) STEADY SHOT (Menu setting) ..................................... OFF
7) FOCUS (Menu setting) .......................................... MANUAL
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Center Frame”. If not,
perform “6. Picture Frame
Setting (Center Frame)”
is “Center Frame”. If not,
perform “6. Picture Frame
Setting (Center Frame)”
2
0
01
01
3
6
02
Check the data is “00”.
(Note 4)
(Note 4)
4
6
D0
Set the following data.
27: NTSC model
23: PAL model
23: PAL model
5
6
D1
Set the following data.
40: NTSC model
00: PAL model
00: PAL model
6
6
01
6F
Press PAUSE (Write) button.
(Note 5)
(Note 5)
7
6
02
Check the data changes to
“01”.
“01”.
Note 4: If not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
Note 5: The adjustment data will be automatically input to page:
6F, address: 2C.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
0
01
00
Order Page Address Data
Procedure
1
0
01
01
2
6
02
Check the data is “00”.
(Note 2)
3
6
01
BB
Press PAUSE (Write) button.
4
6
02
Check the data changes to
“01”.
“01”.
Note 2: If not, select page: 6, address: 02, set data: 00, and press
PAUSE (Write) button.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
0
01
00
6-29
DCR-HC62/HC62E_ADJ
9.
Mechanical Shutter Adjustment
RadarW
RadarW
RadarW
RadarW
RadarW
Adjust the close time and loss time every F number of the me-
chanical shutter and the high-speed shutter correction value to
correct the luminous exposure.
chanical shutter and the high-speed shutter correction value to
correct the luminous exposure.
Adjustment Page
6F
Adjustment Address
76 to 8B
Note 1: If reading/writing data on pages 6F, set data: 06 to page:
0, address: 10, and then select pages: F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2: NTSC model: DCR-HC62
PAL model: DCR-HC62E
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 06.
3) Input the following data to page: 6F, address: 76 to 8B.
Note 3: Press the PAUSE (Write) button of the adjustment re-
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 06.
3) Input the following data to page: 6F, address: 76 to 8B.
Note 3: Press the PAUSE (Write) button of the adjustment re-
mote commander each time to set data.
Address
Data
NTSC
PAL
76
5C
4D
77
00
00
78
47
3C
79
00
00
7A
3E
34
7B
00
00
7C
38
2F
7D
00
00
7E
28
20
7F
00
00
80
62
60
81
7A
75
82
81
7B
83
7C
76
84
6A
63
85
1E
1E
86
80
80
87
80
80
88
80
80
89
80
80
8A
80
80
8B
80
80
4) Select page: 0, address: 10, and set data: 00.
5) Select page: 0, address: 01, and set data: 00.
5) Select page: 0, address: 01, and set data: 00.
6-30
DCR-HC62/HC62E_ADJ
10. Picture Frame Setting
(Color reproduction adjustment frame)
Subject
Color bar chart
(Color reproduction adjustment
frame)
(1 m (PTB-450) or 40 cm (PTB-
1450) from the front of lens)
(Color reproduction adjustment
frame)
(1 m (PTB-450) or 40 cm (PTB-
1450) from the front of lens)
Measurement Point Video terminal of A/V
R jack
(75
Ω terminated)
Measuring Instrument
Oscilloscope and monitor TV
Specified Value
A=B, C=D, E=F
Note 1: Perform “Hall Adjustment” and “Flange Back Adjust-
ment” before this adjustment.
Note 2: Check that the data of page: 0, address: 10 is “00”.
Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ..................................... OFF
6) FOCUS (Menu Setting) ......................................... MANUAL
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ..................................... OFF
6) FOCUS (Menu Setting) ......................................... MANUAL
Setting method:
Order
Procedure
1
Adjust the zoom and the camera direction, and set
the specified position.
the specified position.
2
Mark the position of the picture frame on the monitor
TV, and adjust the picture frame to the this position
in following adjustment using “Color reproduction
adjustment frame”.
TV, and adjust the picture frame to the this position
in following adjustment using “Color reproduction
adjustment frame”.
How to read the XH, XL, YH and YL data:
Order Page Address Data
Procedure
1
0
03
18
2
1
Read XH data and XL data.
(Note 3)
(Note 3)
3
0
03
22
4
1
Read YH data and YL data.
(Note 3)
(Note 3)
Note 3: The right four digits of the page: 1 displayed data of the
adjusting remote commander.
1:XX : XX
XL or YL data
XH or YH data
XH or YH data
How to reset the zoom and focus when they deviated:
If the zoom and focus deviated due to some reason, reset them in
the following method.
If the zoom and focus deviated due to some reason, reset them in
the following method.
Order Page Address Data
Procedure
1
6
90
XL
2
6
91
XH
3
6
92
YL
4
6
93
YH
5
6
01
79
Press PAUSE (Write) button.
Check on the oscilloscope
1. Horizontal period
Fig. 6-1-11
2. Vertical period
Fig. 6-1-12
Check on the monitor TV (Underscanned mode)
Fig. 6-1-13
A=B
C=D
A
B
C
D
E=F
V
E
F
Color bar chart picture frame
Monitor TV picture frame
How to release the picture frame setting:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
6
90
00
3
6
91
00
4
6
92
00
5
6
93
00
6-31
DCR-HC62/HC62E_ADJ
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”
2
0
01
01
3
6
02
Check the data change to
“00”. (Note 4)
“00”. (Note 4)
4
6
D0
Set the following data, and
press PAUSE (Write) button.
press PAUSE (Write) button.
7C: NTSC model
82: PAL model
82: PAL model
5
6
01
3D
Press PAUSE (Write) button.
6
0
10
06
7
6
00
Set the following data, and
press PAUSE (Write) button.
press PAUSE (Write) button.
77: NTSC model
F7: PAL model
F7: PAL model
8
Adjust the GAIN and
PHASE of the vectorscope,
and set to the burst lumi-
nance point to the burst
position of color reproduc-
tion frame.
PHASE of the vectorscope,
and set to the burst lumi-
nance point to the burst
position of color reproduc-
tion frame.
9
F
Change the data and settle
each color luminance point in
each color reproduction
frame. (Note 5)
each color luminance point in
each color reproduction
frame. (Note 5)
10
0
10
00
Note 4: If not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
Note 5: Be sure to press the PAUSE (Write) button of the adjust-
ing remote commander before changing the addresses.
If not, the new data will not be written to the memory.
If not, the new data will not be written to the memory.
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
0
01
00
3
Perform “Color Reproduc-
tion Check”.
tion Check”.
11. Color Reproduction Adjustment
Adjust the color separation matrix coefficient so that proper color
reproduction is produced.
Adjust the color separation matrix coefficient so that proper color
reproduction is produced.
Subject
Color bar chart
(Color reproduction adjustment
frame)
(Color reproduction adjustment
frame)
Measurement Point
Video terminal of A/V R jack
(75
(75
Ω terminated)
Measuring Instrument
Vectorscope
Adjustment Page
6F
Adjustment Address
37, 39, 40, 41
Specified Value
All color luminance points should
settle within each color reproduction
frame.
settle within each color reproduction
frame.
Note 1: If reading/writing data on pages 66, 6F, set data: 06 to
page: 0, address: 10, and then select pages: 6, F. By this
data setting, the pages 66, 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
data setting, the pages 66, 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2: Perform “Hall Adjustment” and “Flange Back Adjust-
ment” before this adjustment.
Note 3: NTSC model: DCR-HC62
PAL model: DCR-HC62E
Switch setting:
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADYSHOT (Menu setting) ...................................... OFF
6) FOCUS (Menu setting) .......................................... MANUAL
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADYSHOT (Menu setting) ...................................... OFF
6) FOCUS (Menu setting) .......................................... MANUAL
37
39
40
41
39
40
41
(66)
(6F)
Click on the first or last page to see other DCR-HC62 / DCR-HC62E (serv.man4) service manuals if exist.