DOWNLOAD Sony DCR-HC62 / DCR-HC62E (serv.man4) Service Manual ↓ Size: 1.91 MB | Pages: 74 in PDF or view online for FREE

6-32

DCR-HC62/HC62E_ADJ

R-Y

B-Y

R

G

B

M

G

C

Y

Y

E

Burst
position

R-Y

B-Y

R

G

B

M

G

C

Y

Y

E

Burst
position

6-33

DCR-HC62/HC62E_ADJ

Subject

Color bar chart (Color reproduction
adjustment frame)

Measurement Point

Video terminal of A/V R jack
(75 

Ω terminated)

Measuring Instrument

Vectorscope

Adjusting
remote
commander

Specified Value

All color

Data of page: 6,

luminance

address: 0C is

points should

“00”

settle within each
color
reproduction
frame.

Note 1: Perform “Color Reproduction Adjustment” before this

adjustment.

Note 2: Perform this along with the “Color Reproduction Adjust-

ment” successively.

Note 3: Check that the data of page: 0, address: 10 is “00”.
Note 4: NTSC model: DCR-HC62

PAL model: DCR-HC62E

Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ..................................... OFF
6) FOCUS (Menu setting) .......................................... MANUAL

Order Page Address Data

Procedure

1

Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”

2

0

01

01

3

6

02

Check the data is “0

0”.

(Note 5)

4

6

D0

Set the following data, and
press PAUSE (Write) button
 7C: NTSC model
 82: PAL model

5

6

01

4D

Press PAUSE (Write) button.
(Note 6)

6

6

02

Check the data changes to
“01”.

7

6

0C

Check the data is “00”.

Note 5: If not, select page: 6, address: 01, set data: 00, and press

PAUSE (Write) button.

Note 6: Confirm that the Y signal level (A) is 90±5 IRE.

(Refer to Fig 6-1-16)
90

±5 IRE = 606.9 to 678.3 mV (NTSC)

90

±5 IRE = 595 to 665 mV (PAL)

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE (Write) button.

2

0

01

00

A

White

6-34

DCR-HC62/HC62E_ADJ

How to reset the zoom and focus when they deviated:
If the zoom and focus deviated due to some reason, reset them in
the following method.

Order Page Address Data

Procedure

1

6

90

XL

2

6

91

XH

3

6

92

YL

4

6

93

YH

5

6

01

79

Press PAUSE (Write) button

Subject

Clear chart (AWB Adjustment frame)
(1 m (PTB-450) or 40 cm (PTB-1450)
from the front of lens)

Measurement Point

Video terminal of  A/V R jack (75 

Ω

terminated)

Measuring Instrument

Monitor TV

Specified Value

Only the clear chart must be shot
(entire screen is white).

Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: The right four digits of the page: 1 displayed data of the

adjusting remote commander.

1:XX : XX

XL or YL data
XH or YH data

Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ..................................... OFF
6) FOCUS ................................................................... MANUAL

Order Page Address Data

Procedure

1

Perform “10. Picture Frame
Setting (Color reproduction
adjustment frame)”.

2

By zooming in the color
reproduction adjustment
picture frame, set up the
picture frame in which the
color bar is shot on full
screen. (Refer to Fig. 6-1-17)

3

Remove the Color bar chart
from the pattern box.

4

Check that whole of the
screen is white.

5

0

03

18

6

1

Read XH data and XL data.
(Note 2)

7

0

03

22

8

1

Read YH data and YL data.
(Note 2)

9

0

03

00

10

In the following adjustment, if
the “AWB Adjustment frame”
is used, adjust the clear chart
to this position.

Color bar chart picture frame

Monitor TV picture frame

6-35

DCR-HC62/HC62E_ADJ

Adjust the white balance reference at 3200K, and adjust the nor-
mal coefficient of the light value.

Subject

Clear chart
(AWB Adjustment Frame) (Note 3)

Adjustment Page

6F

Adjustment Address

2E to 31, E8 to EB, 2A, 2B

Note 1: Perform “Color Reproduction Adjustment” before this

adjustment.

Note 2: If reading/writing data on pages 6F, set data: 06 to page:

0, address: 10, and then select pages: F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.

Note 3: Perform “13. Picture Frame Setting (AWB Adjustment

Frame)” before this adjustment.

Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ..................................... OFF
6) FOCUS (Menu setting) .......................................... MANUAL

Order Page Address Data

Procedure

1

Check that the picture frame
is “AWB Adjustment Frame”.
If not,  perform “13. Picture
Frame Setting (AWB
Adjustment Frame)”

2

0

01

01

3

6

02

Check the data is “00”.
(Note 4)

4

6

01

B5

Press PAUSE (Write) button.
(Note 5)

5

6

02

Check the data changes to
“01”.

Note 4: If not, select page: 6, address: 01, set data: 00, and press

PAUSE (Write) button.

Note 5: The adjustment data will be automatically input to page:

6F, address: 2E to 31, E8 to F3, 2A, 2B.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE (Write) button.

2

0

01

00