DOWNLOAD Sony SLV-D500P (serv.man2) Service Manual ↓ Size: 14.16 MB | Pages: 125 in PDF or view online for FREE

2-11

1) Remove the Belt Pulley. (Refer to Fig. 2-38)
2) Remove the Gear Loading Drive 1 after releasing Hook [A] in

the direction arrow as shown in detail drawing.

3) Remove the Slider Cam 2.
4) Remove the Lever Load 3, Link Load 5 & Lever Load 4, Link

Load 6.

Fig. 2-21 Gear Loading Drive, Slider Cam,

Lever T, S Load Ass’y Removal

1) When reinstalling, be sure to align dot of Lever Load T Ass’y 1

with dot of Lever Load S Ass’y 2 as shown in drawing, (Refer to
Timing Point 1).

2) Insert the Pin A,B,C,D into the Slider Cam 3 hole,
3) Be sure to align dot of Lever Load T 1 and dot of Gear Loading

Drive 4, (Refer to Timing Point 2).

4) Aline dot of Gear Loading drive 4 with mark of Slider Cam 3

as shown in drawing (Refer to Timing Point 3).

Fig. 2-22 Gear Loading Drive, Slider Cam,

Lever Load S, T Ass’y Assembly

1

GEAR LOADING DRIVE

5

LINK LOAD S

3

LEVER LOAD S

4

LEVER LOAD T

6

LINK LOAD T

2

SLIDE CAM

HOOK(A)

2

LEVER LOAD S 

1

LEVER LOAD T 

LEVER LOAD S 

LEVER LOAD T 

PIN A

PIN C

PIN B

PIN D

3

SLIDER CAM

TIMING POINT 2

TIMING POINT 1

TIMING POINT 3

2-12

1

SPRING TENTION LEVER

STOPPER

MARK[B]

"A"

2

LEVER TENTION ASS`Y

3

BAND BRAKE ASS`Y

1) Remove the Lever Pinch Drive 1, Lever Tension Drive 2.

Fig. 2-23 Lever Pinch Drive,

Lever Tension Drive Removal

1) Remove the Lever Brake S Ass’y (Refer to Fig 2-25).
2) Remove the Spring Tension Lever 1.
3) Rotate stopper of Main Base in the direction of arrow “A”.
4) Lift the Lever Tension Ass’y 2 & Band brake
Ass’y 3.

1) When replacing the Lever Tension Ass’y 2, be sure to apply Grease

on the post,

2) Take care not to touch stain on the felt side, and not to be folder

and broken Band brake Ass’y

3) After Lever Tension Ass’y seated, Rotate stopper of Main Base to

the Mark[B].

Fig. 2-24 Lever Tension Ass’y,

Band Brake Ass’y Removal

1

LEVER PINCH DRIVE 

2

LEVER TENSION DRIVE 

2-13

1) Release the Hook [A] and the Hook [B], [C] in the direction of

arrow as shown in Fig 2-25.

2) Lift the Lever S, T Brake Ass’y 1, 2 with spring brake 3.

1) Assembly the Lever S Brake Ass’y 1 on the Main Base.
2) Assembly the Lever T Brake Ass’y 2 with spring brake 3.

 Take extreme care not to be folded and

transformed Spring Brake at removing or reinstalling.

Fig. 2-25 Lever Brake S, T Ass’y Removal

1) Push the Lever Idle 1 in the direction of arrow “A”, “B”.
2) Lift the Lever Idle 1.

1) Apply oil in two Bosses of Lever Idle 1.
2) Assemble the Gear Idle 2 with the Lever Idle 1.

 When replacing the Gear Idle 2, be sure to add oil in the boss

of Lever Idle 1.

Fig. 2-26 Gear Idle Ass’y Removal

1

LEVER S BRAKE ASS'Y

2

LEVER T BRAKE ASS`Y

3

SPRING BRAKE

HOOK(B)

HOOK(C)

HOOK(A)

2

GEAR IDLE

2

GEAR IDLE

1

LEVER IDLE

"A"

HOOK "C"

"B"

2-14

1) Lift the Disk S, T Reel 1, 2.

Fig. 2-27 Disk S, T Reel Removal

1) Remove the Washer Slit 1.
2) Lift the Holder Clutch Ass’y 2.

 When you reinstall Holder Clutch Ass’y

1) Check the condition of spring as shown in detail A.
2) Don't push Holder Clutch Ass’y down with excessive force Just

insert Holder Clutch Ass’y into post center with dead force and
Rotate it smoothly.
Be sure to confirm that spring is in the slit of Gear Center Ass’y as
shown in detail B.

Fig. 2-28 Holder Clutch Ass’y Removal

1

DISK S REEL

2

DISK T REEL

1

WASHER SLIT

2

HOLDER CLUTCH ASS`Y

DETAIL  A

<BAD>

SPRING

<GOOD>

<BAD>

SPRING

<GOOD>

DETAIL  B