DOWNLOAD Sony GV-D200 Service Manual ↓ Size: 21.2 MB | Pages: 127 in PDF or view online for FREE

5-3

J-1

J-2

J-3

J-4

J-5

Fig. 5-1-1.

J-1

J-2

J-3

J-4

J-5

Adjustment remote commander (RM-95 upgraded).
(Note 1)

CPC-13 jig

Multi CPC jig

Power cord (Note 2)

IR receiver jig

J-6082-053-B

J-6082-443-A

J-6082-311-A

J-6082-223-A

J-6082-383-A

For adjusting the video section

For adjusting the LCD block

For connecting the battery terminal and DC power supply

For adjusting the IR transmitter

For details of the adjustment remote commander, refer to “5-4.
SERVICE MODE”.

• Oscilloscope

• Regulated power supply

• Frequency counter

• Monitor TV

• Digital voltmeter

• Pattern generator

If the micro processor IC in the adjustment remote commander is
not the new micro processor (UPD7503G-C56-12), the pages
cannot be switched. In this case, replace with the new micro
processor (8-759-148-35).

Connect the adjustment remote commander to the LANC jack,
and set to HOLD switch to the “ADJ” side.

5-4

Mechanism Section adjustments, checks, and replacement of
mechanism parts, refer to the separate volume “8mm Video
Mechanism Adjustment Manual 

   B Mechanism  ”.

NTSC model: GV-D200/D800
PAL model: GV-D200E/D800E

1)

Refer to “Section 2. DISASSEMBLY” and supply the power
with the cabinet assembly removed. (So that the mechanical
deck can be operated.)

2)

Connect the adjustment remote commander to the LANC jack.

3)

Turn on the HOLD switch of the adjustment remote
commander.

4)

Close the cassette compartment without loading a cassette and
complete loading.

5)

Select page: 0, address: 01, and set data: 01.

6)

Select page: F, address: 22, set data: 81, and press the PAUSE
button of the adjustment remote commander.

7)

Select page: D, address: 10, set data: 10, and press the PAUSE
button of the adjustment remote commander.

8)

Disconnect the power supply of the unit.
By carrying out the above procedure, the unit can be operated
without loading a cassette. (Note2)
Be sure to carry out “Processing after Operations” after
checking the operations.
Set the data of page: D, address: 10 to “12”, if the sensor
ineffective mode, forced VTR power supply ON mode is to be
used together.

Except for the recording mode.

1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: F, address: 22, set data: 80, and press the PAUSE
button of the adjustment remote commander.

3)

Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjustment remote commander.

4)

Select page: 0, address: 01, and set data: 00.

5)

Disconnect the power supply of the unit.

1)

Clean the tape path face (tape guide, capstan shaft, pinch roller).

2)

Connect the adjustment remote commander to the LANC jack.

3)

Turn on the HOLD switch of the adjustment remote
commander.

4)

Select page: 0, address: 01, and set data: 01.

5)

Select page: 2, address: 2E, and set data: 02.

6)

Select page: F, address: 22, set data: 88, and press the PAUSE
button of the adjustment remote commander.
(Be sure to perform “Processing after operation” after
completing adjustments.)

7)

Connect the oscilloscope to VC-250 board CN933 via CPC-13
jig (J-6082-443-A).

Channel 1: VC-250 board, CN933 Pin 5
External trigger: VC-250 board, CN933 Pin 8

8)

Playback Hi8/standard8 alignment tape for tracking.

(WR5-1NP(NTSC))
(WR5-1CP(PAL))

9)

Check that the oscilloscope RF waveform is flat at the entrance
and exit.
If not flat, adjust according to the separate volume “8mm Video
Mechanical Adjustment Manual 

  B Mechanism  ”.

10) Perform “Processing after operations”, after completing

adjustment.

Table 5-2-1.

1)

Connect the adjustment remote commander, and turn on the
HOLD switch.

2)

Select page: 0, address: 01, and set data: 01.

3)

Select page: 2, address: 2E, and set data: 00.

4)

Select page: F, address: 22, set data: 80, and press the PAUSE
button of the adjustment remote commander.

5)

Select page: 0, address: 01, and set data: 00.

6)

Remove the power supply from the unit.

Fig. 5-2-1.

1

2

3

4

5

6

7

8

9

10

SWP

AFC F0

BPF MONI

F0 ADJ RF IN

PB RF

REG GND

RF AGC OUT

VC RF SWP

NC

NC

11

12

13

14

15

16

17

18

19

20

NC

NC

DV RF SWP

RF IN

CAP FG

RF MON

TMS

TCK

TDO

TDI

Must be flat 

5-5

1)

Connect the adjustment remote commander to the LANC jack.

2)

Turn the HOLD switch of the adjustment remote commander
to the ON position.

3)

Close the cassette compartment without the cassette.

4)

Select page: 3, address: 01, and set data: 0C, and press the
PAUSE button of the adjustment remote commander.
(The mechanism enters the record mode automatically.)

The function buttons becomes inoperable.

5)

To quit the record mode, select page: 3, address: 01, set data:
00, and press the PAUSE button of the adjustment remote
commander. (Whenever you want to quit the record mode, be
sure to quit following this procedure.)

1)

Connect the adjustment remote commander to the LANC jack.

2)

Turn the HOLD switch of the adjustment remote commander
to the ON position.

3)

Close the cassette compartment without the cassette.

4)

Select page: 3, address: 01, and set data: 0B, and press the
PAUSE button of the adjustment remote commander.
(The mechanism enters the playback mode automatically.)

The function buttons becomes inoperable.

5)

To quit the playback mode, select page: 3, address: 01, set data:
00, and press the PAUSE button of the adjustment remote
commander. (Whenever you want to quit the playback mode,
be sure to quit following this procedure.)

1)

Clean the tape running side (tape guide, capstan shaft, pinch
roller).

2)

Input a  color bar signal to the AUDIO/VIDEO INPUT jack.

3)

Connect the adjustment remote commander to the LANC jack.

4)

Turn the HOLD switch of the adjustment remote commander
to the ON position.

5)

Set to the recording mode.

6)

Select page: 3, address: 1C, set data: 5D, and press the PAUSE
button of the adjustment remote commander.

7)

Record for several minutes.

8)

Release the recording mode.

9)

Select page: 3, address: 1C, set data: 00, and press the PAUSE
button.

1)

Clean the tape running side (tape guide, capstan shaft, pinch
roller).

2)

Connect the adjustment remote commander to the LANC jack.

3)

Turn the HOLD switch of the adjustment remote commander
to the ON position.

4)

Connect an oscilloscope to VC-250 board CN933 via the CPC-
13 jig (J-6082-443-A).
Channel 1: VC-250 board, CN933 Pin qh (Note)
External trigger: VC-250 board, CN933 Pin qd

Connect a 75

Ω

 resistor between Pins qh of CN910 and 6

(GND).

5)

Select page: 2, address: 2E, and set data: 01.

6)

Playback the tape path check signal.

7)

Select page: 3, address: 33, and set data: 08.

8)

Select page: 3, address: 26, and set data: 31.

9)

Check that the oscilloscope RF waveform is flat at the entrance
and exit.
If not flat, perform “2-1-2. TAPE PATH ADJUSTMENT “ of
“2-1. Hi8/STANDARD 8mm MODE”.

10) Select page: 3, address: 26, and set data: 00.
11) Select page: 3, address: 33, and set data: 00.
12) Select page: 2, address: 2E, and set data: 00.

Fig. 5-2-2.

Must be flat

Pin 

qd

Pin 

qh

5-6

For details of the adjustment remote commander, refer to “5-4.
SERVICE MODE”.

Use the following measuring instruments for video section
adjustments.

NTSC model:GV-D200/D800
PAL model: GV-D200E/D800E

1)

TV monitor

2)

Oscilloscope (dual-phenomenon, band width above 30 MHz
with delay mode) (Unless specified otherwise, use a 10 : 1
probe.)

3)

Frequency counter

4)

Pattern generator with video output terminal

5)

Digital voltmeter

6)

Audio generator

7)

Audio level meter

8)

Audio distortion meter

9)

Audio attenuator

10) Regulated power supply
11) Digital8 alignment tapes

• SW/OL standard (WR5-2D)

Parts code: 8-967-993-22

• Audio operation check for NTSC (WR5-3ND)

Parts code: 8-967-993-32

• System operation check for NTSC (WR5-5ND)

Parts code: 8-967-993-42

• Audio operation check for PAL (WR5-3CD)

Parts code: 8-967-993-37

• System operation check for PAL (WR5-5CD)

Parts code: 8-967-993-47

12) NTSC Hi8/standard8 alignment tapes (For NTSC model)

• For tracking adjustment (WR5-1NP)

Parts code : 8-967-995-02

• For video frequency characteristics adjustment (WR5-7NE)

Parts code : 8-967-995-13

• For checking Standard 8 mode operations

For LP (WR5-4NL)

Parts code : 8-967-995-51

For SP (WR5-5NSP)

Parts code : 8-967-995-42

The following alignment tapes can also be used.
WR5-4NSP (8-967-995-41)

• For checking Hi8 mode operations

For LP (WR5-8NLE)
Parts code : 8-967-995-52
For SP (WR5-8NSE)
Parts code : 8-967-995-43

• For Checking AFM stereo operations (WR5-9NS)

Parts code : 8-967-995-23

• For BPF adjustment (WR5-11NS)

Parts code : 8-967-995-71

13) PAL Hi8/standard8 alignment tapes (For PAL model)

• For tracking adjustment (WR5-1CP)

Parts code : 8-967-995-07

• For video frequency characteristics adjustment (WR5-7CE)

Parts code : 8-967-995-18

• For checking Standard 8 mode operations

For LP (WR5-4CL)

Parts code : 8-967-995-56

For SP (WR5-5CSP)

Parts code : 8-967-995-47

The following alignment tapes can also be used.
1) WR5-3CL (8-967-995-36)
2) WR5-4CSP (8-967-995-46)

• For checking Hi8 mode operations

For LP (WR5-8CLE)

Parts code : 8-967-995-57

For SP (WR5-8CSE)

Parts code : 8-967-995-48

• For Checking AFM stereo operations (WR5-9CS)

Parts code : 8-967-995-28

• For BPF adjustment (WR5-11CS)

Parts code : 8-967-995-76

14) Adjustment remote commander (J-6082-053-B)
15) CPC-13 jig (J-6082-443-A)
16) Power code (J-6082-223-A)

Connect the adjustment remote commander to the LANC jack,
and set the HOLD switch to the “ADJ” side.

17) IR receiver jig (J-6082-383-A)
18) Multi CPC jig (J-6082-311-A)