Sony KV-XS29M80 Service Manual ▷ View online
–
41
–
KV
-XS29M80/XS29M97
-XS29M80/XS29M97
RM-954
RM-953
2-7-2. REPLACEMENT OF LIGHT GUIDE
2-6. SERVICE POSITION
(Note: Remove F Bracket first.)
2-7. REPLACEMENT OF PARTS
For replacement of the Control Button and Light Guide, unscrew them, exchange
with the new parts, and fix them with screws (+BVTP) respectively.
with the new parts, and fix them with screws (+BVTP) respectively.
2-7-1. REPLACEMENT OF CONTROL BUTTON
Control button
Two screws
(+BVTP 3
(+BVTP 3
×
12)
One screw
(+BVTP 3
(+BVTP 3
×
12)
2-5. F BRACKET REMOVAL
2
Two screws
(+BVTP 3
×
12)
3
F Board bracket
5
Two claws
1
Three connectors
6
F board
–
42
–
KV
-XS29M80/XS29M97
-XS29M80/XS29M97
RM-954
RM-953
2-10. TERMINAL BRACKET REMOVAL
One screw
(+BVTP 3
(+BVTP 3
×
12)
Two screws
(+BVTP 3
(+BVTP 3
×
12)
Two screws
(+BVTP 3
(+BVTP 3
×
12)
2
Two claws
3
Terminal bracket
3
Two screws
Two screws
(+BVTP 3
×
12)
(+BVTP 3
×
12)
2
PWB holder
J4 Board
7
5
6
2-8. D3 BOARD REMOVAL
1
Three connectors
2
One claw
3
D3 board
2-9. PWB HOLDER REMOVAL
2
Two screws
(+BVTP 3
×
12)
PWB holder
2-11. P2, B5 and B7 BOARDS REMOVAL
1
Two claws
One claw
B7 board
P2 board (KV-XS29M97)
B5 board (KV-XS29M80)
B5 board (KV-XS29M80)
–
43
–
KV
-XS29M80/XS29M97
-XS29M80/XS29M97
RM-954
RM-953
2-14.
PICTURE TUBE REMOVAL
4
B3 Board
5
A Board
1
Two screws
(+BVTAP 3
×
12)
2
Two screws
(+BVTAP 3
×
12)
2-13. A AND B3 BOARDS REMOVAL
2-12. H5 BOARD REMOVAL
3
Two connectors
6
One screw (+BVTP 3
×
12 with washer)
1
Two connectors
4
Four claws
5
H5 Board
2
Four connectors
5
Cushion
5
Picture Tube
5
Two screws
(Tapping)
5
Two screws
(Tapping)
5
Tension
spring
5
Deflection
yoke
5
C Board
!∞
Demagnetic Coil
!∞
Four DGC Clips
5
VM1 Board
5
Chassis Assy
5
Anode cap
5
Speaker Bracket Assy (L)
5
Speaker Bracket Assy (R)
2
Four screws
(+BVTAP 3
×
12)
2
Four screws
(+BVTAP 3
×
12)
–
44
–
KV
-XS29M80/XS29M97
-XS29M80/XS29M97
RM-954
RM-953
•
REMOVAL OF ANODE-CAP
NOTE : After removing the anode, short circuit the anode of the picture tube and
the anode cap to the metal chassis, CRT shield or carbon paint on the
CRT.
CRT.
•
REMOVING PROCEDURES
1
Do not damage the surface of anode-caps with sharp shaped objects.
2
Do not press the rubber too hard so as not to damage the inside of anode-cap.
A metal fitting called the shatter-hook terminal is built into the rubber.
A metal fitting called the shatter-hook terminal is built into the rubber.
3
Do not turn the foot of rubber over too hard.
The shatter-hook terminal will stick out or damage the rubber.
The shatter-hook terminal will stick out or damage the rubber.
•
HOW TO HANDLE AN ANODE-CAP
3
When one side of the rubber cap is separated from the anode button, the anode-cap
can be removed by turning up the rubber cap and pulling it up in the direction of the
arrow
can be removed by turning up the rubber cap and pulling it up in the direction of the
arrow
c
.
2
Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow
b
.
1
Turn up one side of the rubber cap in the direction indicated by the arrow
a
.
a
a
b
b
c
Anode button
Click on the first or last page to see other KV-XS29M80 service manuals if exist.