DOWNLOAD Sony KV-XA29M67 Service Manual ↓ Size: 6.83 MB | Pages: 108 in PDF or view online for FREE

– 5 –

Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER
lamp from flashing.

For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be con-
firmed, it is possible to bring up past occurances of failure for confirmation on the screen:

[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:

[Screen display] / channel [5] / Sound volume [-] / Power ON

˘

                  Note that this differs from entering the service mode (mode volume [+]).

STANDBY/SLEEP lamp

Diagnostic Item

Flash Count*

+B overcurrent/overvoltage

2 times

Vertical deflection stopped

White balance failure

5 times

* One flash count is not used for self-diagnostic.

002 : 000
003 : 000
004 : 000
005 : 001

Numeral "0" means that no fault has been detected.

Numeral "1" means a fault has been detected.

101 : 000

SELF DIAGNOSTIC

Lamp ON 0.3 sec.

Lamp OFF 3 sec.

Lamp OFF 0.3 sec.

2 times

3 times

– 6 –

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic
screen during repairs. When you have completed the repairs, clear the result display to “0”.

Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after
completion of the repairs.

[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the
diagnostic screen is being displayed.

Channel [8]

/ 0

[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.

[+B overcurrent ªOCPº]

Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to
ON and the voltage to pin 18 of IC301 should go down when V.SYNC is more than
seven verticals in a period, the unit will automatically turn off.

[Vertical deflection stopped]

Occurs when an absence of the vertical deflection pulse is detected by Q509 and
IC001 shut down the power supply.

[Vertical deflection overcurrent]

Occurs when an overcurrent on V drive line is detected by Q507. Power supply will
be shut down when detect this by IC001.

[White balance failure]

If the RGB levels* do not balance or become low level within 5 seconds, this error
will be detected by IC301. TV will stay on, but there will be no picture.

* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)

IC301

Y/CHROMA JUNGLE

FROM

CRT

[V] Q509/507

IC001

SYSTEM

IC003

MEMORY

IK-IN

MP/
PROTECT

O-LED

IO-8DAT

B-DAT

IO-SDAT

5

21

18

51

46

SDA 35

FROM
[+B] Q604 C1

45

– 7 –

2

To prevent fire or shock hazard, do not expose
the TV to rain or moisture.

Do not operate the TV if any liquid or solid object
falls into it. Have it checked immediately by
qualified personnel only.

Do not open the cabinet and the rear cover of the
TV as high voltages and other hazards are
present inside the TV. Refer servicing and
disposal of the TV to qualified personnel.

Your TV is recommended for home use only.
Do not use the TV in any vehicle or where it may
be subject to excessive dust, heat, moisture or
vibrations.

Do not block the ventilation openings of the TV.
Do not install the TV in a confined space, such
as a bookcase or built-in cabinet.

For children’s safety, do not leave children
alone with the TV. Do not allow children to
climb onto it.

Do not plug in too many appliances to the same
power socket. Do not damage the power cord.

Clean the TV with a dry and soft cloth.
Do not use benzine, thinner, or any other chemicals
to clean the TV. Do not scratch the picture tube.

For your own safety, do not touch any part of the
TV, the power cord and the antenna cable during
lightning storms.

Pull the power cord out by the plug. Do not pull
the power cord itself. Disconnect the TV before
moving it or if you are not going to use it for
several days.

•  Dangerously high voltages are present inside the TV.
•  TV operating voltage: 110 – 240 V AC.

3

Do not install the TV in an unstable position.
Use a proper TV stand.

Do not place any objects on the TV.

–

 8 
–

4

Using Your New TV

1

2

3

R

L

Y

C

B

C

R

WOOFER

4

VIDEO

VIDEO IN

VIDEO OUT

AUDIO

R       L

CAUTION
• Do not connect the power cord until you have completed making all other

connections; otherwise a minimum leakage current might flow through
the antenna and other terminals to ground.

• To avoid battery leakage and damage to the remote, remove the batteries

from the remote if you are not going to use it for several days. If any
liquid that leaks from the batteries touches you, immediately wash it
away with water.

If you wish to connect a VCR, see the Connecting a VCR diagram below.

To watch the video input, press t (see page 11).

To t 1, 2 or 3
(video input)

To 8
(antenna)

5

Using Your New TV

PROGR

MENU

AUTO
PROGR

ENTER

SELECT

L(MONO)

3

Notes
• If you connect a monaural VCR, connect the yellow plug to 

 (the

yellow jack) and the black plug to   -L (MONO) (the white jack).

• If you connect  a VCR  to the 8 (antenna) terminal, preset the signal

output from the VCR to the program number 0 on the TV.

• If both 

 (S video input) and … 1 (video input) at the rear of your TV

are input at the same time, the 

 (S video input) is automatically

selected. To view the video input to t 1 (video input), disconnect the
S video cable.

• Do not connect video equipment to t 3 (video input) at the front and

the rear of your TV at the same time; otherwise the picture will not be
displayed properly on the screen.

• When no signal is input from the connected video equipment, the TV

screen becomes blue.

Note
• Do not use old batteries nor use different types of batteries together.

Tips
• If you want to stop the automatic channel presetting, press MENU.
• If your TV has preset an unwanted channel or cannot preset a particular

channel, then preset your TV manually (see page 31).