DOWNLOAD Sony KV-XA21M81 Service Manual ↓ Size: 3.55 MB | Pages: 62 in PDF or view online for FREE

– 25 –

Preparation :
• Before starting this adjustment, adjust the focus, horizontal

size and vertical size.

• Receive dot/hatch signal.
• Pic mode: Personal (Pic 90%, Brightness 50%, Col 50 %,

Hue 50%, Shp 50%).

1. (Moving horizontally), adjust the H.STAT control so that the

red, green and blue dots are on top of each other at the center
of the screen.

2. (Moving vertically), adjust the V.STAT magnet so that the

red, green and blue dots are on top of each other at the center
of the screen.

3. If the H.STAT variable resistor cannot bring the red, green

and blue dots together at the center of the screen, adjust the
horizontal convergence with the H.STAT variable resistor
and the V.STAT magnet in the manner given below.
(In this case, the H.STAT variable resistor and the V.STAT
magnet influence each other, so be sure to perform
adjustments while tracking.)

1

V. STAT

2

H. STAT VR

3

Center dot

R    G    B

R

G

B

H. STAT VR

V. STAT

Magnet

RV702

H. STAT

C1 Board

BMC (Hexapole)

V.STAT

DY pocket

Purity

V.STAT

BMC

Purity

R

R

R

R

G

G

G

G

B

B

B

B

a

a

a

b

b

b

b

R

R

G

G

B

B

a

a

b

b

b

– 26 –

YCH

Rotate

YCH

VOL on DY

TLV

Insert

TLH

Correction Plate to DY Pocket (Left or
Right)

ON DY:

b

a

c

d

a-d : screen-corner
        misconvergence

YCH

TLV

Preparation:
• Before starting this adjustment, adjust the horizontal static

convergence and the vertical static convergence

4

BMC (Hexapole) Magnet.
If the red, green and blue dots are not balanced or aligned,
then use the BMC magnet to adjust in the manner described
below.

R G

B

R

G

B

R

G B

R

B

R

G

G

G

B

R

B

R B

TLV

YCH

B

R

– 27 –

2. WHITE BALANCE ADJUSTMENT
1) Set to Service Mode (Refer Section 4-1: ADJUSTMENTS

WITH COMMANDER).

2) Input white raster signal.
3) Set the PICTURE to minimum.
4) Select GCT (WHB 4) and BCT (WHB 5) with [1] and [4],

and adjust the level with [3]  and [6] for the best white
balance.

5) Set the PICTURE to maximum.
6) Select GDR (WHB 1) and BDR (WHB 2) with [1] and [4],

and adjust the level with [3] and [6] for the best white
balance.

7) Write into the memory by pressing [MUTING] then [0].

3. SUB BRIGHT ADJUSTMENT
1) Set to service mode.
2) Input a staircase signal of black to white from the pattern

generator.

3) BRIGHTNESS .... 50%.

PICTURE ............ MINIMUM

4) Select SBR (WHB7) with [1] and [4], and adjust SBR

(WHB7) level with [3] and [6] so that the second stripe
from the right is dimly lit.

1. G2 (SCREEN) ADJUSTMENT
1) Set the PICTURE to normal.
2) Put to VIDEO input mode without signals.
3) Connect R, G and B of the C1 board cathode to the

oscilloscope.

4) Adjust BRIGHTNESS to obtain the cathode voltage to the

value below.

5) Adjust G2 (screen) on the FBT until picture shows the

point before cut off.

White

second from the right

Black

0 V

Cathode setting voltage:

175 V 

± 2 (VDC)

F i x   a   P e r m a l l o y   a s s y   c o r r e s p o n d i n g   t o   t h e
misconverged areas.

FOCUS adjustment should be completed before W/B adjustment.

1.

Receive digital monoscope pattern.

2.

Set "Picture Mode" to "DYNAMIC".

3. Adjust focus VR so that the center of screen becomes just

focus.

4. Change the receiving signal to white pattern and blue back.

5. Confirm magenta ring is not noticeable. Incase magenta is

very obvious, adjust focus VR to take balance of magenta

ring and focus.

a

b

c

d

Permalloy assembly

Screen

Focus

– 28 –

Service adjustments to this model can be performed using the
supplied Remote Commander RM-952

a. ENTERING SERVICE MODE
With the unit on standby

This operation sequence puts the unit into service mode.

The screen display is :

Set the standby condition (Press [ P O W E R ]  button on the

commander), then press [POWER] button again, hereupon it

becomes TV mode.

1) Set to Service Mode.

2) Press [1] (UP) and [4] (DOWN), to select the adjustment.

4) Press [MUTING] button to indicate WRITE on the screen.

5) Press [0] button to write into memory.

1) After adjustment, pull out the plug from AC outlet, and then

plug into AC outlet again.

2) Turn the power switch ON and set to Service Mode.

3) Call the adjusted items again to confirm adjustments were

made.

n

 

[DISPLAY]

 

n

 

5

 

n

  

VOL (+)

  

n

 

[POWER]

Item Number 00 of device GEO

This explanation uses H-Position as an example.

1. Select “GEO 00 HPS” with the 1 and 4 buttons.

2. Raise/lower the data with the 3 and 6 buttons.

3. Select the optimum state. (The standard is 1F for PAL

reception.)

4. Write with the 

[MUTING]

 button. (The display changes to

WRITE.)

5. Execute the writing with the - button. (The WRITE

display will be changed to red color while excuting, and

back to SERVICE.)

Example on screen display :-

1, 4

Select the adjustment item.

↓

3, 6

Raise/lower the data value.

↓

[MUTING]

Writes.

↓

 -

Executes the writing.

7, -

All the data becomes the values in memory.

8, -

All user control goes to the standard state.

5, -

Service data initialization (Be sure not to use

usually.)

2, -

Write 50Hz adjustment data to 60Hz, or vice

versa.

Use the same method for all Items. Use 1 and 4 to select the

adjustment item, use 3 and 6 to adjust, write with [MUTING],

then execute the write with -.

Note : 1. In [WRITE], the data for all items are written into

memory together.

2. For adjustment items that have different standard

data between 50Hz or 60Hz, be sure to use the
respective input signal after adjustment.

PAL,SECAM:50
NTSC           :60

00

HPS

1C

SERVICE

Data

Mode

Item 

Name

Item No

Software version

Suffix No
(OEM Code)

Total Power-On time (hours)

p

Marking of new NVM

GEO

1.0C

59

7F

000A

0

631S

Device 

Name

50

1F

SERVICE 50

HPS

Adjusted with [3] 
and [6] buttons.

GREEN

Write with [MUTING]

Write executed with [0]

GEO

00

7F

0

000A

59

631S 1.0C

GREEN

1F

WRITE

50

HPS

GEO

00

7F

0

000A

59

631S 1.0C

1F

SERVICE 50

HPS

RED
The WRITE display
then the display
returns to green
SERVICE

GEO

00

7F

0

000A

59

631S 1.0C