DOWNLOAD Sony KV-SZ292M88 Service Manual ↓ Size: 9.89 MB | Pages: 119 in PDF or view online for FREE

– 12 –

WIRE DRESSING WILL BE ATTACHED LATER IN 
                             SUPPLEMENT.

– 13 –

WIRE DRESSING WILL BE ATTACHED LATER IN 
                             SUPPLEMENT.

– 14 –

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

The controls and switch should be set as follows unless
otherwise noted:
Picture Control....................................."NORMAL"
Brightness Control..............................."NORMAL"

Perform the adjustments in order as follows :

1. Beam Landing
2. Convergence
3. Focus
4. G2(SCREEN)
5. White Balance

Note : Test Equipment Required.

1. Pattern Generator

5. Oscilloscope

2. Degausser

6. Landing Checker

3. DC Power Supply

7. XCV Adjuster

4. Digital Multimeter

Preparation :
• Feed in the white pattern signal.
• Before starting, degauss the entire screen with the

degausser.

• In order to reduce the geomagnetism on the set's picture

tube, face it east or west.

1. Input a raster signal with the pattern generator.
2. Loose the deflection yoke(DY) mounting screw, and set

the purity control to the center as shown below:-

3. Position VM coil as shown below:-

4. Set the raster signal of the pattern generator to green.
5. Move the DY backward and adjust the purity control so

that green is in the center and blue and red are at the
sides evenly.

Red

Blue

Green

a

b

b

c

c

d

d

a

Purity control
corrects this area.

Disc magnets or rotatable
disc magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

Purity control

VM coil

G2

G1

G3

Align the edge of
the VM coil with
the edge of the G3 grid.

G4

......................................................................................................................................................................................................................

6. Then move the DY forward and adjust so that the entire

screen becomes green.

7. Now switch over raster signal to red then blue and

confirm the condition.

8. When the position of the DY is determined, tighten it with

the DY mounting screw.

9. If the beam does not land correctly in all the corners of

the screen, use magnet disc to correct it.

– 15 –

Moved RV750 (H.STAT)

R

R

G

G

B

B

A

A

B

B

B

B

R

G

G

R

B

Preparation:
• Before starting, perform FOCUS adjustment.
• Picture Mode "CUSTOM"
• Receive dot/cross hatch pattern.

1. (Moving vertically), adjust the 4 pole magnet to

converge red, green and blue dots in the center of
the screen.

2. Tilt the 4 pole magnet and adjust static convergence

to open or close the 4 pole magnet.

3. When the 4 pole magnet is moved in the direction of

arrow 

A

 and 

B

, the red, green and blue dots moves

as shown below:-

b) Horizontal Static Convergence
If the blue dots does not converge with the red and
green dots, use the 6 pole magnet to adjust in
the manner described below:-

1. Receive cross hatch signal.
2. Set Picture to "MINIMUM", Brightness to "STANDARD".
3. Adjust the Y separation axis correction magnet on

the Neck Assembly so that the horizontal lines at
the top and bottom of the screen are straight.

Red

Blue

Red

Blue

6 Pole Magnet

4 pole Magnet

DY pocket

Purity

6 Pole

Magnet

4 Pole

Magnet

R G

B

R

G

B

R

G B

R

B

R

G

G

G

B

R

B

4 pole magnet

RV750
H. STAT

RV1800
G2 (SCREEN) 

Center dot

R     G     B

G

R

B