DOWNLOAD Sony KV-SZ252M50 Service Manual ↓ Size: 9.04 MB | Pages: 71 in PDF or view online for FREE

– 12 –

Dress Lead Assy, Speaker to center position of Rotation Coil using purse lock Ø 9 as shown. Make sure Earth 
Assy, Coating wire is above Lead Assy, Speaker. This is to keep Lead Assy, Speaker away from Deflection Yoke.

TVSR Requirement: 
1. Keep HV cable away from conductive parts
 (distance of 1mm/kV).
2. Keep spacing between edge of anode cap 
& conductive parts (distance of 0.5mm/kV).
3. Keep spacing between edge of anode cap & 
non-conductive parts (distance of at least 5mm or more).

Earth Assy, Coating

wire

Dress Lead Assy, Speaker to

center position of Rotation Coil

using purse lock Ø 9

DGC Connector is below Conn Assy,

3P VH to keep Conn Assy, 3P VH

away from Heatsink A007 and D604

Keep wires away from 

heatsinks A007, D604 and 

conductive parts

Apply to all SZ252 Narrow 220V CISPR models ONLY

Clamp the ferrite core at the end of the DGC

wire as shown. Position it directly above DGC 

Connector's housing

Purse lock Ø 9

Rotation Coil

Lead Assy, Speaker
(RED+BLK)

Earth Assy, Coating wire is
above Lead Assy, Speaker

Rotation coil

DGC Connector

A007

D604

DGC Band

HV Cap

Rotation coil

DGC

CN605

CN6620

Housing

Connector Assy,

3P VH

DY

Rotation Coil

Attach purse lock Ø 9

here

Lead Assy,

Speaker

Lead Assy,

Speaker

Lead Assy, Speaker

goes behind DGC

Dress Lead Assy, Speaker

directly on to DGC using

purse lock Ø 9

Pull wire to left

Lead Assy, Speaker

goes behind DGC

Pull wire to 

the right

Loop Lead Assy, Speaker and  

dress directly on to DGC using  

purse lock 

Ø 9

– 13 –

Dress Cap Assy, High Voltage with Holder, HV Cable combi as shown.

CAUTION: 1) Make sure the specified position is 
 

being followed.

                  2)  Position the Cap Assy, High Voltage in 
 

the inner ring of the Holder, HV cable  

 

combi (see diagram).

TVSR requirement:
1. Spacing between HV cable and other conductive
part's surface is 1mm/kV or more.
2. Spacing between HV cable's and enclosure with
ventilation or the edge where terminal bracket and  
rear cover meet: 10mm or more.

Install AC cord holder to AC power cord at specified position as shown.

290 ± 5mm 

630 ± 5mm 

Hook AC cord into

CRT support's hook

Make sure AC cord is

straight between 

boss and holder

Attach AC cord onto

holder and insert to

bottom cover

Attach Purse Lock (S)

Ø 8 in to rear cover

Holder, HV cable combi

250 ± 5 mm

Large hook

Top view

Rotation coil

DGC

Dress behind boss

AC Cord Holder

Inner Ring

CRT's carbon

area

HV cap

10 o'clock position

purse lock 

Ø

 9.

Dress Holder, HV Cable Combi to Cap Assy,

High Voltage and attach side hook to rotation

coil at 10 o'clock position. Then, attach large

hook to DGC and dress with

purse lock 

Ø

 9.

DGC

Side hook

Large 

hook

P-P taping

of DGC

Dress using Purse lock 

Ø

 9

Dress Holder, HV Cable

Combi to the right of P-P

taping of DGC. Dress

purse lock 

Ø

 9 to the right

of large hook on Holder,

HV Cable Combi.

CRT's carbon

area

Min. distance = 1mm/kV

Min. distance = 1mm/kV

Keep distance of HV cable

from other wires, conductive

parts and CRT's carbon area

Purse lock 

Ø

 9

Side hook

– 14 –

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

The controls and switch should be set as follows unless
otherwise noted:
Picture Control....................................."NORMAL"
Brightness Control..............................."NORMAL"

Perform the adjustments in order as follows :

1. Beam Landing
2. Convergence
3. Focus
4. G2(SCREEN)
5. White Balance

Note : Test Equipment Required.

1. Pattern Generator

5. Oscilloscope

2. Degausser

6. Landing Checker

3. DC Power Supply

7. XCV Adjuster

4. Digital Multimeter

Preparation :
• Feed in the white pattern signal.
• Before starting, degauss the entire screen with the

degausser.

• In order to reduce the geomagnetism on the set's picture

tube, face it east or west.

1. Input a raster signal with the pattern generator.
2. Loose the deflection yoke(DY) mounting screw, and set

the purity control to the center as shown below:-

3. Position Neck Assy as shown below:-

4. Set the raster signal of the pattern generator to green.
5. Move the DY backward and adjust the purity control so

that green is in the center and blue and red are at the
sides evenly.

Red

Blue

Green

a

b

b

c

c

d

d

a

Purity control
corrects this area.

Disc magnets or rotatable
disc magnets correct these
areas (a-d).

Deflection yoke positioning
corrects these areas.

Purity control

Neck assy

G2

G1

G3

Align the edge of
the neck assy with
the edge of the G2 grid.

......................................................................................................................................................................................................................

6. Then move the DY forward and adjust so that the entire

screen becomes green.

7. Now switch over raster signal to red then blue and

confirm the condition.

8. When the position of the DY is determined, tighten it with

the DY mounting screw.

9. If the beam does not land correctly in all the corners of

the screen, use magnet disc to correct it.

– 15 –

Moved RV750 (H.STAT)

R

R

G

G

B

B

A

A

B

B

B

B

R

G

G

R

B

Preparation:
• Before starting, perform FOCUS adjustment.
• Picture Mode "CUSTOM"
• Receive dot/cross hatch pattern.

1. (Moving vertically), adjust the 4 pole magnet to

converge red, green and blue dots in the center of
the screen.

2. Tilt the 4 pole magnet and adjust static convergence

to open or close the 4 pole magnet.

3. When the 4 pole magnet is moved in the direction of

arrow A and B, the red, green and blue dots moves
as shown below:-

b) Horizontal Static Convergence
If the blue dots does not converge with the red and
green dots, use the 6 pole magnet to adjust in
the manner described below:-

1. Receive cross hatch signal.
2. Set Picture to "MINIMUM", Brightness to "STANDARD".
3. Adjust the Y separation axis correction magnet on

the Neck Assembly so that the horizontal lines at
the top and bottom of the screen are straight.

Neck assy

Neck assy

Red

Blue

Red

Blue

VM board

VM board

6 Pole Magnet

4 pole Magnet

DY pocket

Purity

6 Pole

Magnet

4 Pole

Magnet

R G

B

R

G

B

R

G B

R

B

R

G

G

G

B

R

B

4 pole magnet

RV750
H. STAT

RV1800
G2 (SCREEN) 

Center dot

R     G     B

G

R

B