Sony KV-SW292M80 Service Manual ▷ View online
–
29
–
KV-SW292M
80
RM-GA002
3-3-4 SUB BRIGHT ADJUSTMENT
1. Set TV to RF mode.
2. Input PAL monoscope to RF mode (OTHER model) and
2. Input PAL monoscope to RF mode (OTHER model) and
NTSC monoscope (NTSC model).
3. Set Brightness to 50% and Picture to “MINIMUM” in
"CUSTOM" mode.
4. Select WHBL 010 “SBRT” with 1 and 4 button and
adjust its data using 3 and 6 button so that the Cut
Off level and slightly glimmer is as the specification
below:-
Off level and slightly glimmer is as the specification
below:-
5.
Write into the memory by pressing [MUTING] t -.
6. Copy the adjusted data WHBL 010 “SBRT” to Video
mode.
7. Once adjustment is completed in RF and Video mode,
carry out adjustment in DVD mode. Repeat step 2 to 3.
Select WHBL 010 “SBRT” and adjust its data as the
specification below:-
Select WHBL 010 “SBRT” and adjust its data as the
specification below:-
3-4. GEOMETRY ADJUSTMENT
3-4-1. H-TRAPEZOID ADJUSTMENT
1.
Receive cross hatch/dot signal.
2.
Adjust RV1800 on C Board to make H-Trapezoid
distortion best/to obtain the center illustration shown in
Table 1.
distortion best/to obtain the center illustration shown in
Table 1.
3-4-2. NORMAL MODE 50Hz / 60Hz
1.
Input PAL Special Color Bar (SPCB) or PAL Monoscope
(OTHER model) and Video mode or NTSC Monoscope
(NTSC model) signal using a pattern generator.
(OTHER model) and Video mode or NTSC Monoscope
(NTSC model) signal using a pattern generator.
2.
Set Wide Mode to “OFF”.
3.
Select Category items listed in Table 1.
4.
Raise and Lower the data value using 3 and 6 button
to obtain the center illustration.
to obtain the center illustration.
5.
Press [MUTING] t - to save the data into the memory.
6.
For Korea models, copy adjusted 60Hz to 50Hz. Add 6
steps to 50Hz “HPOS” and 3 steps to 50Hz “HSIZ” and
save the data.
steps to 50Hz “HPOS” and 3 steps to 50Hz “HSIZ” and
save the data.
TV size
Cut Off
Slightly Glimmer
25"
10 IRE
20 IRE + 2 steps
29"
10 IRE
20 IRE + 2 steps
34"
10 IRE
20 IRE + 2 steps
28"
10 IRE
20 IRE
32"
10 IRE
20 IRE
TV size
Cut Off
Slightly Glimmer
25"
10 IRE
20 IRE + 2 steps
29"
10 IRE
20 IRE
34"
10 IRE
20 IRE + 2 steps
28"
10 IRE
20 IRE
32"
10 IRE
20 IRE
– 30 –
KV-SW292M80
RM-GA002
3-4-3. WIDE MODE 50Hz / 60Hz
(V Compression Adjustment)
(V Compression Adjustment)
1.
Input PAL Special Color Bar (SPCB) (OTHER model) or
Monoscope NTSC (NTSC model) signal using a pattern
generator.
Monoscope NTSC (NTSC model) signal using a pattern
generator.
2.
Set Wide Mode to “ON”.
3.
Copy NORMAL MODE 50Hz/60Hz adjusted data for the
following items:-
GEOM: 011 VSIZ, 010 VSLP, 012 SCOR and 003 VLIN
following items:-
GEOM: 011 VSIZ, 010 VSLP, 012 SCOR and 003 VLIN
4.
Select Category items listed in Table 1 except GEOM:
003 VLIN, 010 VSLP, 011 VSIZ, and 012 SCOR and
adjust the data to obtain the center illustration.
003 VLIN, 010 VSLP, 011 VSIZ, and 012 SCOR and
adjust the data to obtain the center illustration.
5.
Press [MUTING]
t - to save the data into the memory.
6.
For Korea models, copy adjusted 60Hz to 50Hz. Add 6
steps to 50Hz “HPOS” and save the data.
steps to 50Hz “HPOS” and save the data.
Category
Function
Illustration
GEOM 000
H Position
(HPOS)
GEOM 001
H Parallelogram
(HPAR)
GEOM 002
H Bow
(HBOW)
GEOM 003
Linearity
(VLIN)
GEOM 005
EW Width
(HSIZ)
Note: Adjust HSIZ
16.6 + -(SPCB) _ 50Hz
14.8 + -(PAL Monoscope) _ 50Hz
15.3 + -(NTSC Monoscope) _ 60Hz
14.8 + -(PAL Monoscope) _ 50Hz
15.3 + -(NTSC Monoscope) _ 60Hz
GEOM 006
EW Parabola/Width
(EWPW)
GEOM 007
EW Upper Corner
(UCOP)
Parabola
GEOM 008
EW Lower Corner
(LCOP)
Parabola
GEOM 009
EW Trapezoid
(EWTZ)
GEOM 010
V-Slope
(VSLP)
GEOM 011
V-Amplitude
(VSIZ)
Note: Adjust VSIZ
12.6 + -(SPCB) _ 50Hz
11.3 + -(PAL Monoscope) _ 50Hz
11.7 + -(NTSC Monoscope) _ 60Hz
11.3 + -(PAL Monoscope) _ 50Hz
11.7 + -(NTSC Monoscope) _ 60Hz
GEOM 012
S-Correction
(SCOR)
GEOM 013
V-Shift
(VPOS)
Table 1
– 31 –
KV
-SW292M80
-SW292M80
RM-GA002
SECTION 4
DIA
GRAMS
4-1.
BLOCK DIA
GRAM
VIF
SAW
SIF
SAW
MAIN
Power
Supply
Stdby
Power
FSS TUNER
Y
U
V
L
R
24.576MHz
DVD in
Rear AV in
Front AV in
Mon out
* FM Radio Function (STEREO model)
Mon
out
AV1
AV3
in
AV2
in
DVD
in
AC in ~
110 ~ 220V
CISPR/
PFC
Relay
LOW B
Stdy 3.3
AUDIO VCC
L
Audio Amp
ATT
NVM
V Def
H Def
DF
DQP
H Def
DF
DQP
VM
RGB Amp
Rot Amp
LCC Amp
6W
R
6W
L,R
H
P
P
EW, Hd
L,R
V+, V-
PWM
RGB
SIRCS
KEY
buttons
PLL
I/O Port
I/O Port
VIF & SIF
POWER
Color
Decoder
YUV
Processor
Jungle
RGB
A
D
C
C
D
A
C
Stereo,
DSP
Micro
Text
CC & V-chip
LED
+B
– 32 –
KV-SW292M80
RM-GA002
4-2. CIRCUIT BOARDS LOCATION
4-3. SCHEMATIC DIAGRAM INFORMATION
Note:
•
•
All capacitors are in µF unless otherwise noted.
•
All electrolytic capacitors are rated at 50V unless otherwise
noted.
noted.
•
All resistors are in ohms.
kΩ = 1000Ω, MΩ = 1000kΩ
kΩ = 1000Ω, MΩ = 1000kΩ
•
Indication of resistance which does not have rating electrical
power is as follows.
power is as follows.
Pitch: 5 mm
Rating electrical power 1/4W (CHIP: 1/10W)
Rating electrical power 1/4W (CHIP: 1/10W)
•
: nonflammable resistor.
•
: fusible resistor.
•
¢
: internal component.
•
: panel designation or adjustment for repair.
•
All variable and adjustable resistors have characteristic curve
B unless otherwise noted.
B unless otherwise noted.
•
Readings are taken with a color-bar signal input.
no mark
no mark
: Common
(
)
: PAL
[
]
: NTSC 3.58
•
Readings are taken with a 10MΩ digital multimeter.
•
Voltage are dc with respect to ground unless otherwise
noted.
noted.
•
Voltage variations may be noted due to normal production
tolerances.
tolerances.
•
All voltage are in Volt.
•
✽
: Cannot be measured.
•
Circled numbers are waveform references.
•
: B +bus.
•
: B –bus.
•
k
: signal path.
Note: The reference number which starts with Wxxx
(eg: W003) indicates a wire to wire connection.
Note: Components marked as XX are not fitted on this
model.
Reference information
RESISTOR
RESISTOR
: RN
METAL FILM
: RC
SOLID
: FPRD
NONFLAMMABLE CARBON
: FUSE
NONFLAMMABLE FUSIBLE
: RS
NONFLAMMABLE METAL OXIDE
: RB
NONFLAMMABLE CEMENT
: RW
NONFLAMMABLE WIREWOUND
:
✽
ADJUSTMENT RESISTOR
COIL
: LF-8L
MICRO INDUCTOR
CAPACITOR
: TA
TANTALUM
: PS
STYROL
: PP
POLYPROPYLENE
: PT
MYLAR
: MPS
METALIZED POLYESTER
: MPP
METALIZED POLYPROPYLENE
: ALB
BIPOLAR
: ALT
HIGH TEMPERATURE
: ALR
HIGH RIPPLE
Note:
The component identified by shading and
mark
mark
! are critical for safety. Replace only
with part number specified.
Note: "A" board schematic diagram is divided into 3
blocks. Each block is named by its function and
block "number". eg: Processor/Audio/Tuner/Jack
(Block 001).
Joint connection between boards can be identified
using the block number followed by the grid's guide.
block "number". eg: Processor/Audio/Tuner/Jack
(Block 001).
Joint connection between boards can be identified
using the block number followed by the grid's guide.
eg:-
<
+B
002:16F
Meaning: Block 001 joint "+B" is connected to Block
002 joint "+B" located at grid 16F.
002 joint "+B" located at grid 16F.
A Board
C Board
F1 Board
H7 Board
VM Board
J3 Board
H4 Board
F2 Board
Click on the first or last page to see other KV-SW292M80 service manuals if exist.