Sony KV-SW292M50 (serv.man3) Service Manual ▷ View online
–
33
–
KV
-SW292M50/M91K
-SW292M50/M91K
RM-GA002
SECTION 4
DIA
GRAMS
4-1.
BLOCK DIA
GRAM
VIF
SAW
SIF
SAW
MAIN
Power
Supply
Stdby
Power
FSS TUNER
Y
U
V
L
R
24.576MHz
DVD in
Rear AV in
Front AV in
Mon out
* FM Radio Function (STEREO model)
Mon
out
AV1
AV3
in
AV2
in
DVD
in
AC in ~
110 ~ 220V
CISPR/
PFC
Relay
LOW B
Stdy 3.3
AUDIO VCC
L
Audio Amp
ATT
NVM
V Def
H Def
DF
DQP
H Def
DF
DQP
VM
RGB Amp
Rot Amp
LCC Amp
6W
R
6W
L,R
H
P
P
EW, Hd
L,R
V+, V-
PWM
RGB
SIRCS
KEY
buttons
PLL
I/O Port
I/O Port
VIF & SIF
POWER
Color
Decoder
YUV
Processor
Jungle
RGB
A
D
C
C
D
A
C
Stereo,
DSP
Micro
Text
CC & V-chip
LED
+B
– 34 –
KV-SW292M50/M91K
RM-GA002
A Board
C Board
F1 Board (except KV-SW292M91K)
H7 Board
VM Board
J3 Board
H4 Board
F2 Board
(KV-SW292M50(Vietnam))
(KV-SW292M50(Vietnam))
F1 Board
(KV-SW292M91K)
(KV-SW292M91K)
K2 Board
(KV-SW292M91K)
(KV-SW292M91K)
B Board (KV-SW292M91K)
PF Board
(KV-SW292M91K)
(KV-SW292M91K)
4-2. CIRCUIT BOARDS LOCATION
4-3. SCHEMATIC DIAGRAM INFORMATION
Note:
•
•
All capacitors are in
µF unless otherwise noted.
•
All electrolytic capacitors are rated at 50V unless otherwise
noted.
noted.
•
All resistors are in ohms.
k
k
Ω = 1000Ω, MΩ = 1000kΩ
•
Indication of resistance which does not have rating electrical
power is as follows.
power is as follows.
Pitch: 5 mm
Rating electrical power 1/4W (CHIP: 1/10W)
Rating electrical power 1/4W (CHIP: 1/10W)
•
: nonflammable resistor.
•
: fusible resistor.
•
¢
: internal component.
•
: panel designation or adjustment for repair.
•
All variable and adjustable resistors have characteristic curve B
unless otherwise noted.
unless otherwise noted.
•
Readings are taken with a color-bar signal input.
no mark
no mark
: Common
(
)
: PAL
[
]
: NTSC 3.58
•
Readings are taken with a 10M
Ω digital multimeter.
•
Voltage are dc with respect to ground unless otherwise
noted.
noted.
•
Voltage variations may be noted due to normal production
tolerances.
tolerances.
•
All voltage are in Volt.
•
✽
: Cannot be measured.
•
Circled numbers are waveform references.
•
: B +bus.
•
: B –bus.
•
k
: signal path.
Note: The reference number which starts with Wxxx
(eg: W003) indicates a wire to wire connection.
Note: Components marked as XX are not fitted on this
model.
Reference information
RESISTOR
RESISTOR
: RN
METAL FILM
: RC
SOLID
: FPRD
NONFLAMMABLE CARBON
: FUSE
NONFLAMMABLE FUSIBLE
: RS
NONFLAMMABLE METAL OXIDE
: RB
NONFLAMMABLE CEMENT
: RW
NONFLAMMABLE WIREWOUND
:
✽
ADJUSTMENT RESISTOR
COIL
: LF-8L
MICRO INDUCTOR
CAPACITOR
: TA
TANTALUM
: PS
STYROL
: PP
POLYPROPYLENE
: PT
MYLAR
: MPS
METALIZED POLYESTER
: MPP
METALIZED POLYPROPYLENE
: ALB
BIPOLAR
: ALT
HIGH TEMPERATURE
: ALR
HIGH RIPPLE
Note:
The component identified by shading and
mark
mark
! are critical for safety. Replace only
with part number specified.
Note: "A" board schematic diagram is divided into 3
blocks. Each block is named by its function and
block "number". eg: Processor/Audio/Tuner/Jack
(Block 001).
Joint connection between boards can be identified
using the block number followed by the grid's guide.
block "number". eg: Processor/Audio/Tuner/Jack
(Block 001).
Joint connection between boards can be identified
using the block number followed by the grid's guide.
eg:-
<
+B
002:16F
Meaning: Block 001 joint "+B" is connected to Block
002 joint "+B" located at grid 16F.
002 joint "+B" located at grid 16F.
KV-SW292M50
KV-SW292M91K
Click on the first or last page to see other KV-SW292M50 (serv.man3) service manuals if exist.