DOWNLOAD Sony KV-SW213M85 Service Manual ↓ Size: 6.21 MB | Pages: 67 in PDF or view online for FREE

– 9 –

FBT Flange

(i) Non 3D models

(ii) 3D models

(iii) For non 3D and 3D

RY600

AC Cord 

540 ± 5 

(

Pull towards right

Pull wires towards right to prevent

slacking, then dress wires above

capacitors' height as shown --> prevent

from touching high temperature parts

Lead Assy, Focus

FBT Flange

Make sure

rubber cap is

pushed

down to make

sure it covers

the FBT flange

completely

Keep wires above of
RY600
--> prevent wires
from being
sandwiched with
front jack & pushed
against relay

Dress AC Power Cord with

Standing Purse Lock, followed
by Lead Assy, Earth and Lead

Assy, Speaker (RED+BLK).

Keep wires above of RY600
--> prevent wires from being
sandwiched with front jack & 
pushed against relay

Dress AC Power Cord

with Standing Purse

Lock, followed by Lead

Assy, Earth and Lead

Assy, Speaker

(RED+BLK).

Dress AC Power Cord and Lead

Assy, Speaker (WHT+BLK) with

Pin, Wire A016

Keep Conn. Assy, 3P

above bunch of wires

Dress AC Power Cord and Lead

Assy, Speaker (WHT+BLK) with

Pin, Wire A016

HV cable

RY600

Lead Assy,

Speaker (RED+BLK)

Lead Assy, Earth

AC Power Cord

CAUTION:
Make sure wires are kept away from sharp edges,
heatsinks & other high-temperature parts

– 10 –

Earth Assy, Coating

Standing Purse Lock

Non-3D models

3D models

Standing Purse Lock 

DGC Conn 

Lead Assy,

Speaker (RED+BLK)

AC Power Cord

Lead Assy, Earth 

Make sure the round
side of spring tension
is installed to Earth
Assy, Coating

Dress wires away from beznet's front terminal --> Prevent

wires from being sandwiched when docking chassis.

Make sure Lead Assy, Earth is

kept away from group of

heatsinks

Dress AC Power Cord and

Lead Assy, Speaker

(WHT+BLK) with Pin, wire

A016

Conn Assy, 3P is above
AC Power Cord and bunch
of wires & towards LEFT
of Standing Purse Lock.

Dress AC Power Cord and

Lead Assy, Speaker

(WHT+BLK) with Pin, wire

A016

Dress DGC Conn together with AC Power Cord, Lead Assy, Earth & Lead

Assy, Speaker (RED+BLK) which are dressed during Chassis Assy as shown

in Figure 2.4(i)

Dress DGC Conn together with AC Power Cord, Lead Assy, Earth & Lead

Assy, Speaker (RED+BLK) which are dressed during Chassis Assy as

shown in Figure 2.4(ii)

CAUTION:
1. Prevent wires from being sandwiched with
  beznet's front terminal when docking chassis.
2. Dress speaker wire & AC cord above capacitors
  near it --> prevent from touching high-temp parts.

– 11 –

Black tape

Standing purse lock

DGC Conn 

Lead Assy, Earth

AC Power Cord

Lead Assy,

Speaker (RED+BLK)

DGC

Earth Assy, Coating

Spring extension

Right Speaker

Keep wires away from sharp

edge of spring extension --> to

prevent scratching on wires.

Keep Lead Assy, Speaker

(RED+BLK) close to CRT surface.

Lead Assy, Speaker (RED+BLK) is

sandwiched between DGC & CRT surface

Ensure wires are kept

away from heatsink.

Left Speaker

Ensure DGC Connector
is kept behind of black tape

From braided wire
of Earth Assy,
Coating at CRT

Dress Connector

Assy, 7P with cable

tie at alignment hole
A. Make sure end of

cable tie is facing

inwards --> to

prevent rattle sound

Earth Assy, Coating is in

front of DGC before

looping it once around DGC

Ensure Earth Assy, Coatin is close to CRT
surface before making a loop around DGC

Connected

to C board.

Earth Assy, Coating is
in front of DGC before
looping it once around

DGC.

Ensure DGC Connector

is kept behind of DGC

DGC Connector in front of DGC before

dress with standing purse lock.

Make sure wire does not touch heatsink

or other high temperature parts

CAUTION:
1. Prevent cable tie from touching rear
cover or any enclosures by turning them
away from it --> to avoid ratlle sound &
prevent cable tie from touching solder
side of board.

1) Pull wires towards right
--> to prevent slacking of wire

2) Insert Lead Assy, Speaker (WHT+BLK) followed by
AC Power Cord in CRT support's hook. Make sure Lead
Assy, Speaker (WHT+BLK) is secured behind AC Power
Cord & does not touch heatsinks.

– 12 –

DY Connector

Conn Assy, 5P (200V)

Earth Assy, Coating

1) DY Connector
goes underneath of
Earth Assy, Coating
and Connector Assy,
5P (200V) wire.

2) DY Connector goes above
Connector Assy, 5P (200V) wire.

Black tape

Top switch wire

under DGC & left

of black tape

Top switch

wire under

DGC & right
of black tape

Ensure Top Switch wire
is dressed around AC
Power Cord --> keep
away from heatsink

3) Dress DY
Connector and
Connector Assy, 5P
(200V) wire with Purse
Lock Ø5.

Use heatsink height to

estimate purse lock location

Purse Lock Ø5

Dress wires away

from FBT area

Conn Assy, 5P

(200V)

DY Connector

TVSR (Clause 9.4.7):
All wires must be kept away from FBT
area by a distance of 10mm or more.

Make sure DY Connector is on

the right side of Earth Assy, Coating.