DOWNLOAD Sony KV-SW213M85 Service Manual ↓ Size: 6.21 MB | Pages: 67 in PDF or view online for FREE

– 8 –

CAUTION :
1.  Do not overpull the wires during dressing

--> avoid disconnection of wires.

2.  Make sure wires are kept away from

sharp edges, heatsinks & other
high-temperature parts.

A

CN801

C

W068

W069

R828

R829

R889

UL wire

P/N 1-923-082-52

Ensure UL wire does not touch high
temperature resistors R828, R829 & R889

W052

Lead Assy, Jumper

Conn Assy, 5P (YUV)

Make sure the UL tape is

positioned

at the sharp edge of

shield case to

prevent wire from being

scratched

Connector Assy, 5P & Lead Assy, 

Jumper go around shield case &

dress with pin wire A021

R121

Lead Assy, G2 & 200V wire on C Board

UL wire P/N 1-923-082-52 on A Board (W068-W069)

CAUTION:
Dress & control mounted wires (Lead Assy, G2 & 200V wire) on C board
if necessary :
--> ensure wires do not get trapped during solder dip process
--> ensure wires do not get punched by ICT jig (modify ICT jig if applicable)

CAUTION:
1) Keep UL wire close to
board surface
2) Make sure wires are 
kept away from 
high-temperature parts
3) Ensure wires do not get
punched by ICT jig (modify
ICT jig if applicable)

CN703:
Ensure Pin 
1 is 
connected
to orange
wire 
(200V)

W700:
Board-
in Lead
Assy, 
G2

W051

Keep UL wire close to
board surface --> vertical
seam improvement

Make sure Conn Assy, 5P

does not touch resistor, R121

Keep Lead Assy, Jumper

away from shield case -->

C/M for OSD drift from RF to

Video mode

Make sure the Connector Assy,

5P is kept close to board surface.

CAUTION:
1) Dress Lead Assy, Jumper according to the green route.
  => Ensure Lead Assy, Jumper is dress away from shield case in the boxed area.
  => Ensure Lead Assy, Jumper is dress below Conn Assy, 5P (YUV).
2) Make sure wires are kept away from sharp edges, heatsinks & other high-temperature parts

– 9 –

FBT Flange

(i) Non 3D models

(ii) 3D models

(iii) For non 3D and 3D

RY600

AC Cord 

540 ± 5 

(

Pull towards right

Pull wires towards right to prevent

slacking, then dress wires above

capacitors' height as shown --> prevent

from touching high temperature parts

Lead Assy, Focus

FBT Flange

Make sure

rubber cap is

pushed

down to make

sure it covers

the FBT flange

completely

Keep wires above of
RY600
--> prevent wires
from being
sandwiched with
front jack & pushed
against relay

Dress AC Power Cord with

Standing Purse Lock, followed
by Lead Assy, Earth and Lead

Assy, Speaker (RED+BLK).

Keep wires above of RY600
--> prevent wires from being
sandwiched with front jack & 
pushed against relay

Dress AC Power Cord

with Standing Purse

Lock, followed by Lead

Assy, Earth and Lead

Assy, Speaker

(RED+BLK).

Dress AC Power Cord and Lead

Assy, Speaker (WHT+BLK) with

Pin, Wire A016

Keep Conn. Assy, 3P

above bunch of wires

Dress AC Power Cord and Lead

Assy, Speaker (WHT+BLK) with

Pin, Wire A016

HV cable

RY600

Lead Assy,

Speaker (RED+BLK)

Lead Assy, Earth

AC Power Cord

CAUTION:
Make sure wires are kept away from sharp edges,
heatsinks & other high-temperature parts

– 10 –

Earth Assy, Coating

Standing Purse Lock

Non-3D models

3D models

Standing Purse Lock 

DGC Conn 

Lead Assy,

Speaker (RED+BLK)

AC Power Cord

Lead Assy, Earth 

Make sure the round
side of spring tension
is installed to Earth
Assy, Coating

Dress wires away from beznet's front terminal --> Prevent

wires from being sandwiched when docking chassis.

Make sure Lead Assy, Earth is

kept away from group of

heatsinks

Dress AC Power Cord and

Lead Assy, Speaker

(WHT+BLK) with Pin, wire

A016

Conn Assy, 3P is above
AC Power Cord and bunch
of wires & towards LEFT
of Standing Purse Lock.

Dress AC Power Cord and

Lead Assy, Speaker

(WHT+BLK) with Pin, wire

A016

Dress DGC Conn together with AC Power Cord, Lead Assy, Earth & Lead

Assy, Speaker (RED+BLK) which are dressed during Chassis Assy as shown

in Figure 2.4(i)

Dress DGC Conn together with AC Power Cord, Lead Assy, Earth & Lead

Assy, Speaker (RED+BLK) which are dressed during Chassis Assy as

shown in Figure 2.4(ii)

CAUTION:
1. Prevent wires from being sandwiched with
  beznet's front terminal when docking chassis.
2. Dress speaker wire & AC cord above capacitors
  near it --> prevent from touching high-temp parts.

– 11 –

Black tape

Standing purse lock

DGC Conn 

Lead Assy, Earth

AC Power Cord

Lead Assy,

Speaker (RED+BLK)

DGC

Earth Assy, Coating

Spring extension

Right Speaker

Keep wires away from sharp

edge of spring extension --> to

prevent scratching on wires.

Keep Lead Assy, Speaker

(RED+BLK) close to CRT surface.

Lead Assy, Speaker (RED+BLK) is

sandwiched between DGC & CRT surface

Ensure wires are kept

away from heatsink.

Left Speaker

Ensure DGC Connector
is kept behind of black tape

From braided wire
of Earth Assy,
Coating at CRT

Dress Connector

Assy, 7P with cable

tie at alignment hole
A. Make sure end of

cable tie is facing

inwards --> to

prevent rattle sound

Earth Assy, Coating is in

front of DGC before

looping it once around DGC

Ensure Earth Assy, Coatin is close to CRT
surface before making a loop around DGC

Connected

to C board.

Earth Assy, Coating is
in front of DGC before
looping it once around

DGC.

Ensure DGC Connector

is kept behind of DGC

DGC Connector in front of DGC before

dress with standing purse lock.

Make sure wire does not touch heatsink

or other high temperature parts

CAUTION:
1. Prevent cable tie from touching rear
cover or any enclosures by turning them
away from it --> to avoid ratlle sound &
prevent cable tie from touching solder
side of board.

1) Pull wires towards right
--> to prevent slacking of wire

2) Insert Lead Assy, Speaker (WHT+BLK) followed by
AC Power Cord in CRT support's hook. Make sure Lead
Assy, Speaker (WHT+BLK) is secured behind AC Power
Cord & does not touch heatsinks.